• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1294-1296
• /
• 1998

Platinum thin films which hardly form volatile compounds with any reactive gas at normal process temperature was etched in Inductively Coupled Plasma (ICP) using Ar/HBr/$Cl_2$ gases. It is observed that the etch rate of platinum is reduced as increasing of HBr/$Cl_2$ gas mixing ratio when Ar gas ratio is fixed. However, we obtain good etching profile of platinum films without unwanted residues in 90% Ar/5% HBr/5% $Cl_2$ gas mixing ratio.

• Transactions on Electrical and Electronic Materials
• /
• v.1 no.3
• /
• pp.14-17
• /
• 2000

Giga bit dynamic random access memory(DRAM) requires the capacitor of high dielectric films. Some metal oxides films have been proposed as the dielectric material . And Pt is one of the most promising electrode materials. However very little has been done in developing the etching technologoy Pt film. Therefore, it is the first priority to develop the technology for plasma etching of Pt film. In this study, the dry etching of Pt film was investigated in Inductively Coupled Plasma(ICP) etching system with Cl$_2$/Ar and HBr/Cl$_2$/Ar gas mixing. X-ray photoelectron spectroscopy (XPS) was used in analysis of sidewall residues for the understanding of etching mechanism. We found the etch residues on the pattern sidewall is mainly Pt-Pt, Pt-Cl and Pt-Br compounds, Etch profile was observed by Scanning Electron Spectroscopy(SEM) . The etch rate of Pt film at 10%, Cl$_2$/90% Ar gas mixing ration was higher than at 100%. Ar. Addition of HBr to Cl$_2$/Ar as an etching gas led to generally higher selectivity to SiO$_2$. And the etch residues were reduced at 5% HBr/5% Cl$_2$/90% Ar gas mixing ration. These pages provide you with an examples of the layout and style which we wish you to adopt during the preparation of your paper, Make the width of abstract to be 14cm.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.886-890
• /
• 2003

The etching characteristics of a LiNbO$_3$ single crystal have been investigated using helicon wave plasma source with bias power and the mixture of CF$_4$, HBr, SF$_{6}$ gas parameters. The etching rate of LiNbO$_3$ with etching parameters was evaluated by surface profiler. The etching surface was evaluated by Atomic Force Microscopy (AFM). The surface morphology of the etched LiNbO$_3$ changed with bias power and the mixture of CF$_4$/Ar/Cl$_2$, HBr/Ar/Cl$_2$, and SF$_{6}$/Ar/Cl$_2$ parameters. Optimum etching conditions, considering both the surface flatness and etch rate were determined.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.2
• /
• pp.83-92
• /
• 1999

GaN etching was performed using planar inductively coupled $Cl_2$-based plasmas and the effects of main process parameters on the characteristics of the plasmas and their relations to GaN etch rates were studied. Also, the GaN etch mechanism was investigated using a Langmuir probe and optical emission spectroscopy (OES) during the etching, and X-ray photoelectron spectroscopy (XPS) of the etched surfaces. The GaN etch rates increased with the increase of chlorine radical density and ion energy, and a vertical etch profile haying the etch rate close to 4000 $\AA$/min could be obtained. The addition of 10% Ar to $Cl_2$ gas increased the GaN etch rate and the addition of Ar (more than 20%) and HBr generally reduced the GaN etch rate. The GaN etch rate appeared to be more affected by the chemical reaction between Cl radicals and GaN compared to the physical sputtering itself under the sufficient ion bombardments to break GaN bonds.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.132.2-132.2
• /
• 2007

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.363-363
• /
• 2008

The development of dry etching process for sapphire wafer with plasma has been key issues for the opto-electric devices. The challenges are increasing control and obtaining low plasma induced-damage because an unwanted scattering of radiation is caused by the spatial disorder of pattern and variation of surface roughness. The plasma-induced damages during plasma etching process can be classified as impurity contamination of residual etch products or bonding disruption in lattice due to charged particle bombardment. Therefor, fine pattern technology with low damaged etching process and high etch rate are urgently needed. Until now, there are a lot of reports on the etching of sapphire wafer with using $Cl_2$/Ar, $BCl_3$/Ar, HBr/Ar and so on [1]. However, the etch behavior of sapphire wafer have investigated with variation of only one parameter while other parameters are fixed. In this study, we investigated the effect of pressure and other parameters on the etch rate and the selectivity. We selected $BCl_3$ as an etch ant because $BCl_3$ plasmas are widely used in etching process of oxide materials. In plasma, the $BCl_3$ molecule can be dissociated into B radical, $B^+$ ion, Cl radical and $Cl^+$ ion. However, the $BCl_3$ molecule can be dissociated into B radical or $B^+$ ion easier than Cl radical or $Cl^+$ ion. First, we evaluated the etch behaviors of sapphire wafer in $BCl_3$/additive gases (Ar, $N_2,Cl_2$) gases. The behavior of etch rate of sapphire substrate was monitored as a function of additive gas ratio to $BCl_3$ based plasma, total flow rate, r.f. power, d.c. bias under different pressures of 5 mTorr, 10 mTorr, 20 mTorr and 30 mTorr. The etch rates of sapphire wafer, $SiO_2$ and PR were measured with using alpha step surface profiler. In order to understand the changes of radicals, volume density of Cl, B radical and BCl molecule were investigated with optical emission spectroscopy (OES). The chemical states of $Al_2O_3$ thin films were studied with energy dispersive X-ray (EDX) and depth profile anlysis of auger electron spectroscopy (AES). The enhancement of sapphire substrate can be explained by the reactive ion etching mechanism with the competition of the formation of volatile $AlCl_3$, $Al_2Cl_6$ or $BOCl_3$ and the sputter effect by energetic ions.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.406-406
• /
• 2010

일반적으로, 나노스케일의 MOS 소자에서는 게이트 절연체 두께가 감소함에 따라 tunneling effect의 증가로 인해 PID (plasma induced damage)로 인한 소자 특성 저하 현상을 감소하는 추세로 알려져 있다. 하지만 요즘 많이 사용되고 있는 high-k 게이트 절연체의 경우에는 오히려 더 많은 charge들이 trapping 되면서 PID가 오히려 더 심각해지는 현상이 나타나고 있다. 이러한 high-k 게이트 식각 시 현재는 주로 Hf-based wet etch나 dry etch가 사용되고 있지만 gate edge 영역에서 high-k 게이트 절연체의 undercut 현상이나 PID에 의한 소자특성 저하가 보고되고 있다. 본 연구에서는 이에 차세대 MOS 소자의 gate stack 구조중 issue화 되고 있는 metal gate 층과 gate dielectric 층의 식각공정에 각각 중성빔 식각과 중성빔 원자층 식각을 적용하여 전기적 손상 없이 원자레벨의 정확한 식각 조절을 해줄 수 있는 새로운 two step 식각 공정에 대한 연구를 진행하였다. 먼저 TiN metal gate 층의 식각을 위해 HBr과 $Cl_2$ 혼합가스를 사용한 중성빔 식각기술을 적용하여 100 eV 이하의 에너지 조건에서 하부층인 $HfO_2$와 거의 무한대의 식각 선택비를 얻었다. 하지만 100 eV 조건에서는 낮은 에너지에 의한 빔 스케터링으로 실제 패턴 식각시 etch foot이 발생되는 현상이 관찰되었으며, 이를 해결하기 위하여 먼저 높은 에너지로 식각을 진행하고 $HfO_2$와의 계면 근처에서 100 eV로 식각을 해주는 two step 방법을 사용하였다. 그 결과 anistropic 하고 하부층에 etch stop된 식각 형상을 관찰할 수 있었다. 다음으로 3.5nm의 매우 얇은 $HfO_2$ gate dielectric 층의 정확한 식각 깊이 조절을 위해 $BCl_3$와 Ar 가스를 이용한 중성빔 원자층 식각기술을 적용하여 $1.2\;{\AA}$/cycle의 단일막 식각 조건을 확립하고 약 30 cycle 공정시 3.5nm 두께의 $HfO_2$ 층이 완벽히 제거됨을 관찰할 수 있었다. 뿐만 아니라, vertical 한 식각 형상 및 향상된 표면 roughness를 transmission electron microscope(TEM)과 atomic force microscope (AFM)으로 관찰할 수 있었다. 이러한 중성빔 식각과 중성빔 원자층 식각기술이 결합된 새로운 gate recess 공정을 실제 MOSFET 소자에 적용하여 기존 식각 방법으로 제작된 소자 결과를 비교해 본 결과 gate leakage current가 약 one order 정도 개선되었음을 확인할 수 있었다.