• Smart Structures and Systems
• /
• v.32 no.1
• /
• pp.1-7
• /
• 2023

In modal analysis, the mode shape reflects the vibration characteristics of the structure, and thus it is widely performed for finite element model updating and structural health monitoring. Generally, the acceleration-based mode shape is suitable to express the characteristics of structures for the translational vibration; however, it is difficult to represent the rotational mode at boundary conditions. A tilt sensor and gyroscope capable of measuring rotational mode are used to analyze the overall behavior of the structure, but extracting its mode shape is the major challenge under the small vibration always. Herein, we conducted a feasibility study on a multi-mode shape estimating approach utilizing a single physical quantity signal. The basic concept of the proposed method is to receive multi-metric dynamic responses from two sensors and obtain mode shapes through bridge loading test with relatively large deformation. In addition, the linear transformation matrix for estimating two mode shapes is derived, and the mode shape based on the gyro sensor data is obtained by acceleration response using ambient vibration. Because the structure's behavior with respect to translational and rotational mode can be confirmed, the proposed method can obtain the total response of the structure considering boundary conditions. To verify the feasibility of the proposed method, we pre-measured dynamic data acquired from five accelerometers and five gyro sensors in a lab-scale test considering bridge structures, and obtained a linear transformation matrix for estimating the multi-mode shapes. In addition, the mode shapes for two physical quantities could be extracted by using only the acceleration data. Finally, the mode shapes estimated by the proposed method were compared with the mode shapes obtained from the two sensors. This study confirmed the applicability of the multi-mode shape estimation approach for accurate damage assessment using multi-dimensional mode shapes of bridge structures, and can be used to evaluate the behavior of structures under ambient vibration.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.295-302
• /
• 2003

A quantitative approach for the retrofit prioritization of bridges is developed based on the damage risk of seismic vulnerable components. In the developed approach, seismic damage risk is estimated in the probabilistic perspectives with an analytical bridge model, which can consider various phenomena found in the seismic behaviors of girder-type bridges and damage models of various vulnerable components. Based on the total cost due to failure of structural components, weighting factors are proposed. Finally, the ranking index and retrofit priority of bridges are estimated from the overall damage risk and weighting factors of bridges. As a result, the retrofit priority of four PSC girder bridges is evaluated by using the proposed approach. The vulnerable components in need of seismic retrofit are selected accordingly. From simulated results, the validity of the proposed approach is verified by comparison with the existing approach. In addition, the proposed approach is found to be appropriate in evaluating the priority of existing bridges.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.4
• /
• pp.13-21
• /
• 2011

Seismic structure pounding between adjacent superstructures may induce the destruction of pier and bridge superstructures and cause local damage that leads to the collapse of the whole bridge system. The pounding problem is related to the expansion of joints, gap distance and seismic response of the abutments. In this research, methods of the contact element approach, the linear spring model, the Kelvin-Voigt model and the Hertz model were studied to analyse the pounding characteristics. The shaking table test for a model specimen such as a bridge superstructure with elastomeric bearings was performed to evaluate the contact element approach methods. Relationships between the time history response from the numerical analysis results and the measured response from the shaking table test are compared. The experimental results were not well matched with the numerical analysis results using the existing pounding stiffness models. Therefore, in this study, coefficients are proposed to calculate the appropriate pounding stiffness ratio.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.481-493
• /
• 2018

Ultrasonic guided waves have attracted increasing attention for non-destructive testing (NDT) and structural health monitoring (SHM) of bridge cables. They offer advantages like single measurement, wide coverage of acoustical field, and long-range propagation capability. To design defect detection systems, it is essential to understand how guided waves propagate in cables and how to select the optimal excitation frequency and mode. However, certain cable characteristics such as multiple wires, anchorage, and polyethylene (PE) sheath increase the complexity in analyzing the guided wave propagation. In this study, guided wave modes for multi-wire bridge cables are identified by using a semi-analytical finite element (SAFE) technique to obtain relevant dispersion curves. Numerical results indicated that the number of guided wave modes increases, the length of the flat region with a low frequency of L(0,1) mode becomes shorter, and the cutoff frequency for high order longitudinal wave modes becomes lower, as the number of steel wires in a cable increases. These findings were used in design of transducers for defect detection and selection of the optimal wave mode and frequency for subsequent experiments. A magnetostrictive transducer system was used to excite and detect the guided waves. The applicability of the proposed approach for detecting and locating wire breakages was demonstrated for a cable with 37 wires. The present ultrasonic guided wave method has been found to be very responsive to the number of brokenwires and is thus capable of detecting defects with varying sizes.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2000.10a
• /
• pp.296-303
• /
• 2000

The purpose of this study is to find inelastic behavior and ductility capacity of reinforced concrete bridge columns under earthquake. Material nonlinearity is taken into account by comprising tensile, compressive and shear models of cracked concrete and a model of reinforcing steel. The smeared crack approach is incorporated. In boundary plane at which each member with different thickness is connected, due to the abrupt change in their stiffness local discontinuous deformation can be taken into account by introducing interface element. Also an analytical model is developed to express the confining effects of lateral tie which depend on the existence or nonexistence and the amounts of transverse confinement, etc. The proposed numerical method for inelastic behavior and ductility capacity of reinforced concrete bridge columns will be verified by comparison with reliable experimental results.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1577-1582
• /
• 2011

Recently rapid construction of bridge is a main interest in construction. A research on rapid construction of pier coping is urgently needed because pier, which is a bridge understructure, directly affect lane reduction and increase of social cost. Precast assembly method and pre-assembly method are the main subjects of rapid construction. But these researches have focused not on reduction of reinforcement amount, but on modifying production method of coping. Reinforcement amount of design specification is as much as that of coping under constructing. So different approach is needed for reduction of reinforcement amount. In this paper, design of pier coping using strut-tie model was proposed for reduction of reinforcement amount and improvement of constructability. Railway bridge pier coping under constructing was analyzed using a finite element method and designed using strut-tie model.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.99-104
• /
• 2002

This paper presents an analytical prediction of the fatigue damage of reinforced concrete bridge columns subjected to cyclic load. Material nonlinearity is taken into account by comprising tensile, compressive and shear models of cracked concrete and a model of reinforcing steel. The smeared crack approach is incorporated. In boundary plane at which each member with different thickness is connected, local discontinuity in deformation due to the abrupt change in their stiffness can be taken into account by introducing interface element. The effect of number of load reversals with the same displacement amplitude has been also taken into account to model the reinforcing steel and concrete. The proposed numerical method for fatigue damage of reinforced concrete bridge columns subjected to cyclic load is verified by comparison with reliable experimental results.

• Computational Structural Engineering
• /
• v.6 no.2
• /
• pp.71-78
• /
• 1993

A method to estimate damage of bridge structures is developed using system identification approach. Dynamic behavior of damaged structures is represented by a non-linear hysteretic moment model. Structural properties can be evaluated through system identification. To incorporate variability of the structural properties and uncertainties of structural response, damage is represented as random quantities. Numerical example is shown for the bridge structure under different ground excitation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.350-355
• /
• 2008

This paper addresses vibration comfort evaluation on suspension bridge subjected to moving vehicles. The moving load method is commonly employed for the analysis, even though it is less accurate than the moving mass approach which considers vehicle-bridge interaction effects and roughness of the pavement. In this study, a parametric study on modeling method by means of the moving load technique, such as the number of modes included in the analysis, types of moving loads, and length of the stiffening girder, is carried out. The numerical result indicated that use of the triangular pulse load may result in significant overestimation on vibration discomfortness.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.3
• /
• pp.526-531
• /
• 2003

In this paper, we implement embedded Linux intelligent controller and remote monitoring system for Bridge Diagnosis. Embedded controller as the hard core is consisted of 32 bit CPU and is designed to have processing of real time monitoring and FFT for Bridge Diagnosis. The prototype monitoring system can operate with world wide web in GUI environment by Java. Detailed design and functional analysis for monitoring system are performed by systems approach.