• 한국분말재료학회지
• /
• 제29권2호
• /
• pp.123-131
• /
• 2022

The purpose of this study is to improve the mechanical properties and develop manufacturing technology through self-soluble alloy powder flame spray coating on the surface of a run-out table roller for hot rolling. The roller surface of the run-out table should maintain high hardness at high temperatures and possess high wear, corrosion, and heat resistances. In addition, sufficient bonding strength between the thermal spray coating layer and base material, which would prevent the peel-off of the coating layer, is also an important factor. In this study, the most suitable powder and process for roll manufacturing technology are determined through the initial selection of commercial alloy powder for roll manufacturing, hardness, component analysis, and bond strength analysis of the powder and thermal spray coating layer according to the powder.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.267-270
• /
• 1999

In this paper, the application of limestone powder, which produced by being gathered electrically in the process of manufacturing of cement, to high fluidity concrete are investigated. According to the experimental results, especially, high viscosity and the loss of air content are accomplished by applying limestone powder as the partial substitution of fine aggregates. In case of hardened concrete, high compressive strength can be achieved by using limestone powder.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.985-986
• /
• 2006

Principal peculiarities of technology for applying coatings of metallic powders on internal surfaces of hollow cylindrical parts by centrifugal method with induction heating from internal surface of part are examined. It is shown that most effective checking and regulating method of sintered powder layer is monitoring the high-frequency current generator power upon contactless pickup indications of external surface temperature of rotating part.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권1호
• /
• pp.1-7
• /
• 2014

기본유체에 나노분말을 분산시킨 나노유체는 기본유체보다 높은 열전도도를 보인다. 이러한 특성으로 인해, 에너지 효율을 향상시키기 위한 대안으로서 나노유체가 주목받고 있으며, 고효율을 필요로 하는 열교환기의 작동유체로 적용하기 위한 많은 연구가 진행되고 있다. 본 연구에서는 상용 열교환기의 작동유체로서 많이 사용되고 있는 증류수, 에틸렌글리콜, 에틸알코올에 나노다이아몬드 분말을 적용한 나노유체의 열전도도를 측정하였다. 나노유체는 매트릭스 합성 분산법을 이용하여 제조하였으며, 나노다이아몬드의 혼합량은 0.1, 0.3, 0.5, 1vol%로 하였다. 측정결과 모든 기본유체 조건에서 나노유체의 열전도도가 증가하였으며, 특히 증류수에 분산된 1vol%의 나노유체에서 23%의 높은 열전도도 향상 경향을 보였다.

• 대한한의학원전학회지
• /
• 제28권4호
• /
• pp.65-77
• /
• 2015

Objectives : This literature study about dental external treatments from Hyangyakjibsungbang Tooth will invigorate applying the therapeutics in the field of Dentistry. Methods : In this study, the parts related to external treatment in the original text of Hyangyakjibsungbang Tooth were reviewed. Results : Examples of frequently used external method were gargling, applying powder, and brushing one's tooth. These methods are still used in modern dental treatment. Conclusions : Discovering new herbal medicines that provide better effects and developing more precise external treatments will advance dental treatment in Korean medicine.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.93-94
• /
• 2006

A novel production method for porous metal components has been developed by applying powder space holder (PSH) method to metal powder injection molding (MIM) process. The PSH-MIM method has an industrial competitive advantage that is capable of net-shape manufacturing the micro-sized porous metal products with complicated shapes and controlled porosity and pore size. In this study, the small impeller with homogeneous micro-porous structure was manufactured by the PSH-MIM method. The effects of combinations in size and fraction of PMMA particle on dimensional tolerance and variation of sintered porous specimens were investigated. It was concluded that the PSH-MIM method could manufacture commercially microporous metal components with high dimensional accuracy.

• 한국세라믹학회지
• /
• 제39권2호
• /
• pp.120-125
• /
• 2002

AC powder EL 소자를 절연층의 유전재료와 후면전극의 전기비저항을 변화시켜 스크린 프린팅법으로 제조하였다. 제조된 소자의 광전기적 특성을 평가하기 위하여 인가 전압은 50∼300 $V_{rms}$까지 변화시켜 휘도 및 전류밀도를 측정하였다. 주파수 및 전압공급원은 정현파 발생 장치로서 frequency generator를 이용하였다. 휘도는 luminometer 의해 측정되었으며 전류밀도 측정을 위하여 multimeter를 사용하였다. 또한 유전층에 대한 유전율을 후막 제조 후 impedance analyser(HP 4194 A)를 이용하여 측정하였다. $TiO_2$ 분말을 $BaTiO_3$에 첨가함에 따라 유전율의 향상으로 초저가형 AC powder EL 소자의 유전층에 적용함으로써 거의 비슷한 전류밀도 하에 50 cd/$m^2$ 정도의 향상된 휘도를 얻을 수 있었다. 저전력 소모형 AC powder EL 소자의 유전층에 적용시 상용분말을 이용한 경우보다 용액 연소법에 의해 제조된 $BaTiO_3$ 분말을 이용한 경우가 더욱 향상된 85 cd/$m^2$ 정도의 휘도를 얻을 수 있었다. 또한 후면전극의 전기 비저항을 조절함으로써 AC powder EL 소자의 휘도는 비교적 감소하지만 전류밀도를 낮출 수 있었다.

• Tribology and Lubricants
• /
• 제33권6호
• /
• pp.296-302
• /
• 2017

Ball milling of elemental powders in advance and using an induction heating system for intermetallic coatings are known to enhance the reactivity of combustion synthesis. In this work, the effects of simultaneously applying these two incentive methods on the properties of intermetallic coatings are studied. Ni-Al powder compacts ball-milled with three different ball-to-powder weight ratio mixtures are synthesized and coated on mild steel by combustion synthesis in an induction heating system. Consequently, similar to an electrical heating system, the positive effects of ball milling on the combustion synthesis are confirmed in the induction heating system. The enhancement in synthetic reactivity achieved by applying the two incentive methods at the same time is greater than that by applying each incentive method separately. In particular, the enhancement is remarkable at low reaction temperature. However, there are limitations to improving the reactivity by simultaneously applying the two incentive methods to the combustion synthesis, unlike the reaction temperature. The microstructure and hardness of the coating layer are both influenced by the ball-charging ratio employed in the ball-milling process.

• 한국산업융합학회 논문집
• /
• 제26권3호
• /
• pp.509-515
• /
• 2023

This study examind the product quality characteristics and industrial application of arrowroot powder added Yanggaeng before its industrial application. Several preliminary experiments were conducted by applying manufacturing conditions and varying the amount of arrowroot powder(1%, 2%, 3%, 4%) added to produce Yanggaeng recipes that can be sold commercially. The moisture content of the produce Yanggaeng was low due to the manufacturing standards, but it showed a significant increase with an increase in the ratio, which was similar to the results of other studies on Yanggaeng. The solubility, particale size distribution, and pH also showed a significant increasing trend. The hardness of arrowroot powder added Yanggaeng decreased with an increase in the amount of arrowroot powder, while springiness, gumminess, and chewiness increased with the addition of arrowroot powder. In terms of color, arrowroot powder showed a dark color, which was well suited to white bean paste and could also be used with black bean paste without any problem. These results were due to the manufacturing ratio being adjusted to meet commercial sales standards, resulting in a lower amount of water being used, and the characteristics of arrowroot powder being applied as they were.

• 한국콘텐츠학회논문지
• /
• 제22권10호
• /
• pp.733-741
• /
• 2022

해양범죄에서 발견되는 다양한 증거물 중 지문과 DNA(Deoxyribo nucleic acid)는 용의자를 특정할 수 있다는 점에서 매우 중요하다. 본 연구에서는 실제 해양환경에서 증거물로 많이 발견되는 비다공성 재질 5종(플라스틱, 스테인리스, 유리, 세라믹, FRP(Fiber reinforced plastic))을 선정하여 자연 및 혈액지문을 유류한 후 동해 해경서 전용부두에서 약 7일간 침지하였다. 그 후 CA(Cyanoacrylate) 훈증법과 4가지 분말법(Swedish black powder, Concentrated black powder, Supranano red powder, Dazzle orange powder)을 이용하여 지문 현출 후 DNA 추출, 정량, STR(Short tandem repeat) 프로필을 분석하였다. 지문현출방법 중 Supranano red powder를 적용하였을 때 DNA 농도가 상대적으로 높은 양이 나타났으며 STR 프로필 분석을 실시한 결과 평균 16.8~9개의 유전자좌위를 확보할 수 있었고, 유리 및 세라믹 재질에서는 20개 모두 확인할 수 있었다. 연구 결과 약 7일 동안 침지된 가상증거물에 지문 현출법을 적용 후 DNA를 추출 및 정량하여 STR 프로필을 확보할 수 있었으며, VMD(Vacuum metal deposition), SPR(Small particle reagent) 등 다양한 지문현출방법을 적용한 뒤 DNA를 분석하여 STR 프로필을 확보할 수 있는 추가적인 연구가 필요할 것으로 판단된다.