• Composites Research
• /
• v.36 no.3
• /
• pp.230-240
• /
• 2023

The deployable reflector antenna consists of 24 unit main reflectors, and is mounted on a launch vehicle in a folded state. This satellite reaches the operating orbit and the antenna of satellite is deployed, and performs a mission. The deployable reflector antenna has the advantage of reduce the storage volume of payload of launch vehicle, allowing large space structures to be mounted in the limited storage space of the launch vehicle. In this paper, structural analysis was performed on the main reflector constituting the deployable reflector antenna, and through this, the initial conceptual design was performed. Lightweight composite main reflector was designed by applying a carbon fiber composite and honeycomb core. The laminate pattern and shape were selected as design variables and a design that satisfies the operation conditions was derived. Then, the performance of the lightweight composite reflector antenna was analyzed by performing detailed structural analysis on modal analysis, quasi-static, thermal gradient, and dynamic behavior.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.1
• /
• pp.23-30
• /
• 2024

This paper dedcribes the design. verification, and analysis techniques for an advanced phased array antenna. When applying an active phased array antenna to an aircraft or missile, miniaturization of the array antenna and wide-angle beam steering characteristics can be unavoidable antenna design considerations. In particular, the active reflection coefficient characteristics when electronically steering a wide-angle beam is a design parameter that must be minimized in terms of system survival and system performance. As a radiator suitable for broadband characteristics and wide-angle beam steering, this paper designed an array structure using SFN and minimized the active reflection coefficient according to beam steering of up to 40° based on the spherical coordivate system angle. The bandwidth of the radiator was confirmed to be 3GHz based on active reflection in the Ka-band. In addition, the performance of the actually manufactured 8by8 array antenna wsa analyzed by measuring the single pattern of the radiator through a near-field test, mathematically synthesizing it, and predicting the Tx/TRx beam used in the seeker system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.1
• /
• pp.36-42
• /
• 2014

In this paper, we propose receiver using ESPAR antenna for diversity gain. The proposed receiver receive signal by changing direction of beam pattern alternately in the OFDM symbol time period when DoA is estimated. In this way, the proposed receiver obtains diversity gain. The proposed receiver has single RF chain. If beam direction is changed alternately then it causes spectrum spread. And then, ICI occur because of spectrum spread. This interference can be equalized at the frequency domain equalizer such as ZF, MMSE and ML. In simulation, the proposed system receive signal using beam pattern of $60^{\circ}$ and beam pattern of $120^{\circ}$ alternately in OFDM symbol time period when it is assumed that DoA is $60^{\circ}$ and $120^{\circ}$. The performance results confirm that it is possible that the proposed receiver obtains diversity gain.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.5
• /
• pp.533-540
• /
• 2008

In the sum and difference pattern synthesis problem of the equi-spaced monopulse tracking linear array antennas, an efficient numerical approach to deriving the relative excitation current weights of antenna elements is presented for the desired patterns. This method is based on the optimum perturbation of null points which are inherent to the Schelkunoffs polynomial representing the pattern array factor. Accordingly, opposite to the conventional method in which the excitation weights are directly optimized, this method is advantageous in that the patterns with the desired individual sidelobe levels(SLLs) and the corresponding excitation weights are easily synthesized by the control of null points. Furthermore, it is showed that two types of difference patterns can be synthesized as imposing the different initial values of null points in the optimization process. The proposed method is numerically validated by synthesizing the patterns with the arbitrary SLLs and substituting the extracted results into the array factor equation.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.9
• /
• pp.877-880
• /
• 2009

A curing process in post-printing section of R2R process is required for an electrical property of the printed pattern when devices such as RFID, Solar cell are printed. PEN as well as heat-stabilized PET which is used as a plastic substrate would be deformed at high temperature due to change of its elastic modulus. And crack in the printed pattern, which is on the plastic substrate is occurred due to the deformation of the substrate. The occurrence of crack causes electrical resistance to increase and the quality of the device to deteriorate. In case of RFID antenna, the range of reading distance is shortened as the electrical resistance of the antenna is increased. Therefore, the deformation of the plastic substrate, which causes the occurrence of crack, should be minimized by setting up low operating tension in R2R process. In low tension, slippage between a moving substrate and a roller would be generated when the operating speed is increased. And scratch would be occurred when slippage is generated due to an air entrainment, which is related to the thickness of the air film. The thickness of the air film is increased when operating speed is increased as shown by simulation based on mathematical model. The occurrence of scratch in conductive pattern printed by roll to roll process is a critical damage because it causes degradation or failure of electrical property of it.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.535-543
• /
• 2009

This paper describes a design for RFID(Radio Frequency Identification) tag antenna using license plate attached the vehicle bumper in 900 MHz band. The proposed tag antenna size which is located on upper center position of a vehicle license plate is 162.5${\times}$40${\times}$1 mm$^3$. A resonant frequency of design antenna and the bandwidth which has return loss of -10 dB below are 900 MHz and about 720 MHz(640${\sim}$1,360 MHz), respectively. The commercial chip impedance considered on design was 16- j131 ${\Omega}$ and the complex conjugate impedance of chip was used as input impedance of tag antenna. The measured return loss and radiation pattern were agreed well with the calculated results. The measured readable range of the proposed tag antenna designed on only the vehicle license plate was 11.5 m. Moreover, its range of the fabricated tag antenna that the license plate and the vehicle bumper were fixed by volt and nut was observed 10.4 m. These measured readable range showed about 5 m above far distance more than the average readable range of commercial tag antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1021-1029
• /
• 2006

In this paper, we designed and implemented a dual wideband dipole type antenna for the reception of S-DMB (Satellite Digital Multimedia Broadcasting) and 2.4/5 GHz WLAN(Wireless Local Area Network) signals. The proposed antenna based on conventional monopole type dual band antenna was implemented as planar wideband dipole type antenna with the volume of $8{\times}33.8{\times}1.68mm^3$. The proposed antenna is printed type on FR4 substrate of 1.6 mm thick and composed of a dipole type antenna for low frequency band and two symmetric structured resonance elements for high frequency band. We confirmed antenna area with dense surface current for each frequency band with simulation. By varying the length of the antenna area with dense surface current, we could vary resonance frequency of each frequency band separately. Impedance bandwidths$(VSWR{\leq}2)$ are 362 MHz(14.23 %) for 2 GHz band and 1188 MHz(22.13, %) for 5 GHz band which show wideband characteristic. Measured maximum gains were 4.33 dBi for 2 GHz band and 5.48 dBi for 5 GHz band which showed improved performance. And the implemented antenna has a good omni-directional radiation pattern characteristic.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.3
• /
• pp.62-72
• /
• 2022

In this study, a miniaturized GPS band(L₁ : 1.575 GHz) antenna that can be mounted on a small drone is proposed. The miniaturization was designed by applying the perturbation method based on the λ/4 microstrip antenna and lengthening the current path at the edge of the patch. The miniaturized antenna was fabricatred such that it could be attached to the surface of styrofoam(ε_r=1.06, t=10 mm) having a size of 10 mm × 9 mm × 10 mm (0.05 λ × 0.05 λ × 0.05 λ). The thickness and length of the feeding line and the spacing between short stubs were adjusted for impedance matching. S₁₁ was found to be -18.8 dB at the center frequency of the fabricated antenna, 1.575 GHz. The radiation pattern measurement results show that the maximum gain of E_θ is 1.87 dBi in 0 directions in the xz-plane, and that E_θ is an omnidirectional characteristic with an average gain of -1.7 dBi in the yz-plane. It was found that the antenna can be used as an ultra-small microstrip antenna, which can be mounted on a small dron for GPS, and is capable of preserving a reduction ratio of 98.8% as compared to a λ/2 microstrip patch antenna.

• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.127-135
• /
• 2018

This paper was studied the tri-band folded monopole antenna design with Mu-negative metamaterial unit cell, which operates at 700 MHz UHD broadcast band and 2.45 GHz/5 GHz WiFi band. The MNR metamaterial is fabricated by forming a capacitor on the backside of the antenna substrate and connecting it to the ground plane through a strip line and a via hole so that a single cell can operate in the MZR (Mu zero resonator). Through this, the resonance point can be controlled to resonate in the zero mode in 700 MHz band, and the bandwidth is improved. Experimental results show that the 10dB bandwidth and gain are 309 MHz (41.2%) and 5.298 dB at the first resonance point, and the 10dB bandwidth and gain at the second resonance point are 821.9 MHz (33.5%) and 2.7840 dB respectively. At the third resonance point, the gain and bandwidth were 1.1314 GHz (20.6%) and 2.9484 dB respectively. We confirmed that the resonance point with theoretical value is in agreement with experimental value. And the radiation pattern is generally omnidirectional, and it has been confirmed that the radiation pattern is good in both forward and backward directions at 0.75 GHz and 2.45 GHz, and has a radiation pattern with multiple lobes at 5.5 GHz.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.339-342
• /
• 2004

In this paper, we investigated methods to reduce SAR(Specific Absorption Rate) value with EMI(Electromagnetic Interference) paint distribution on front case of mobile handset. Simulations for several different EMI patterns were carried out. For the purpose of modeling, we used 3 dimensional CAD(Computer Aided Design) program, `Pro-engineering'. SAR simulation was done with SEMCAD, simulation platform for electromagnetic compatibility antenna design and dosimetry. In order to distinguish the individual pieces and to enable an assignment of the different material properties, each subfile was imported separately. In simulation, folding angle was set to $142^{\circ}.$ If we vary folding angle, different SAR value will be obtained. Among the tested EMI paint patterns, the hairpin pattern showed the best performance, i.e. the decrease efficiency of $16.5\%$ and horizontal-direction zigzag pattern showed the decrease efficiency of $12.2\%$ when we set the completely removed pattern as reference.