• Journal of Magnetics
• /
• 제4권2호
• /
• pp.46-51
• /
• 1999

A solid-HDDR characteristics of the Nd-Fe-B-type alloys magnetic properties of the solid-HDDR treated materials have been investigated using three types of alloys; $Nd_{15}Fe_{77}B_8 (alloy A), Nd_{16}Fe_{75.9}B_8Zr_{0.1}(alloy B), and Nd_{12.6}Fe_{68.7}Co_{11.6}B_8Ga_{1.0}Zr_{0.1} $(alloy C). It has been found that the four-components alloy B and six-components alloy C have showed higher hydrogenation temperatures than the ternary alloy A. The alloys A and B appeared to absorb more hydrogen gas more rapidly as well compared to the alloy C. The disproportionation temperature of hydrogenated materials was exhibited no significant difference among the alloys. The thermal stability of the hydrided materials of the three types of alloys was found to become more stable in order of number of components. The disproportionation and the recombination kinetics were significantly sluggish in the solid-HDDR manner with respect to the conventional manner. Some degree of anisotropic nature was found to exist in the ingot and this anisotropic nature was retained even after the solid-HDDR treatment. It was suggested the solid-HDDR treatment may possibly be used for a preparation of an isotropic or anisotropic Nd-Fe-B-type cast magnets.

• Advances in materials Research
• /
• 제9권1호
• /
• pp.15-32
• /
• 2020

In this article, an analytical solution is presented for the steady-state axisymmetric thermal stress distributions in a composite hollow cylinder. The cylinder is composed of two isotropic and anisotropic materials which is subjected to the thermal boundary conditions of convective as well as radiative heating and cooling on the inner and outer surfaces, respectively. The solution of the temperature is obtained by means of Bessel functions and the thermal stresses are developed using Potential functions of displacement. Numerical results are derived for a cylinder which is similar to a gas turbine combustor and showed that the maximum temperature and thermal stresses (radial, hoop, axial) occurred in the middle point of cylinder and the values of thermal stresses in anisotropic cylinder are more than the isotropic cylinder. It is worthy to note that the values of the thermal conditions which estimated in this research, not to be presented in any other papers but these values are very accurate in calculation.

• Geomechanics and Engineering
• /
• 제28권5호
• /
• pp.493-503
• /
• 2022

Cavity expansion is a classical problem in the field of solid mechanics with a wide range of applications in geotechnical and petroleum engineering. A drained solution is developed for cylindrical cavity expansion in anisotropic soils under biaxial in-situ stresses using a K0-based anisotropic modified Cam-clay model (K0-AMCC). The problem is formulated by solving differential equations using an auxiliary variable, which provides analytical expressions for the volume and four stress components of the soil around the cylindrical cavity. The solution is validated by comparisons with existing well-developed solutions. The results show that the present solution well captures the cavity expansion responses in anisotropic soils under biaxial in-situ stresses, and removes limiting assumptions that the cylindrical cavity expands under uniform in-situ stress in isotropic soils. The elastic-plastic boundary of the expanding cylindrical cavity in K0-consolidated anisotropic soils under biaxial in-situ stresses is a circle rather than an ellipse in isotropic soils, and the mathematical proof is provided in detail.

• 한국세라믹학회지
• /
• 제56권2호
• /
• pp.130-145
• /
• 2019

Widespread commercialization of solid oxide fuel cells (SOFCs) is expected to be realized in various application fields with the advent of cost-effective fabrication of cells and stacks in high volumes. Cost-reduction efforts have focused on production yield, power density, operation temperature, and continuous manufacturing. In this article, we examine several issues associated with processing for SOFCs from the standpoint of the bimodal packing model, considering the external constraints imposed by rigid substrates. Optimum compositions of composite cathode materials with high volume fractions of the second phase (particles dispersed in matrix) have been analyzed using the bimodal packing model. Constrained sintering of thin electrolyte layers is also discussed in terms of bimodal packing, with emphasis on the clustering of dispersed particles during anisotropic shrinkage. Finally, the structural transition of dispersed particle clusters during constrained sintering has been correlated with the structural stability of thin-film electrolyte layers deposited on porous solid substrates.

• 한국자기공명학회논문지
• /
• 제10권1호
• /
• pp.1-37
• /
• 2006

General expressions for solid state NMR lines are described for transitions under static, magic angle spinning, and variable angle spinning conditions in the case where the principal axis system for the anisotropic chemical shift tensor is noncoincident with that of the quadrupole coupling tensor. It is demonstrated that solid state NMR powder pattern simulation program VMAS based on the conventional grid point method of integrating over the Euler angle space is fast enough in comparison with the POWDER simulation package and Gauss-point method.

• Bulletin of the Korean Chemical Society
• /
• 제22권12호
• /
• pp.1375-1379
• /
• 2001

Monte Carlo simulations of hard-spheres confined in parallel hard walls have been carried out extensively at various densities and for various wall distances. The compressibility factors in the directions parallel and normal to the wall have been calculated from the radial free space distribution function (RFSDF) with the results showing that the compressibility factors normal to the wall are smaller than those in parallel direction and that a solid phase is formed in the direction normal to the wall while a fluid phase remains in the parallel direction. An order parameter is found to classify the phases whether a system (or a molecule) is in a fluid or a solid state. The compressibility factors of narrow wall are very small compared to those when the wall is put away. A plausible mechanism of the rise of sap in xylem vessel has been proposed.

• 한국압력기기공학회 논문집
• /
• 제15권1호
• /
• pp.8-17
• /
• 2019

Perforated plates are used for the steam generator tube-sheet and the Reactor Vessel Closure Head in the Nuclear Power Plant. The ASME code, Section III Appendix A-8000, addresses the analysis of perforated plates, however, this analysis is only limited to the flat plate with a triangular perforation pattern. Based on the concept of the effective elastic constants, simulation of flat and spherical perforated plates and their equivalent solid plates were carried out using Finite Element Analysis (FEA). The isotropic material properties of the perforated plate were replaced with anisotropic material properties of the equivalent solid plate and subjected to the same loading conditions. The generated curves of effective elastic constants vs ligament efficiency for the flat perforated plate were in agreement with the design curve provided by ASME code. With this result, a plate with spherical curvature having perforations can be conveniently analyzed with equivalent elastic modulus and equivalent Poisson's ratio.

• Structural Engineering and Mechanics
• /
• 제4권1호
• /
• pp.61-72
• /
• 1996

The time-stepping boundary element method has been so far applied by the authors to transient heat conduction in isotropic solids as well as in orthotropic solids. In this paper, attempt is made to extend the method to 2-D transient heat conduction in arbitrarily anisotropic solids. The resulting boundary integral equation is discretized by means of the boundary element with quadratic interpolation. The final system of equations thus obtained is solved by advancing the time step from the given initial state to the final state. Through numerical compuation of a few examples the potential usefulness of the proposed method is demonstrated.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제29회 추계학술대회논문집
• /
• pp.225-228
• /
• 2007

마이크로 고체 추진제 추력기는 현재의 MEMS 기술로 가장 실현 가능성이 높은 마이크로 추력기이다. 마이크로 고체 추진제 추력기의 기본 요소로는 마이크로 노즐, 마이크로 점화기, 연소 챔버 그리고 고체 추진제이다. 마이크로 노즐과 연소 챔버는 감광유리의 이방성 식각을 통해 제작이 되었다. 마이크로 점화기는 마이크로 유리 박막 백금 히터를 사용하였다. 요소들의 제작 공정을 확립 후, 요소들을 통합하여 추력기를 개발하였다. 추력기의 연소 실험을 수행하여 성공적으로 연소가 일어남을 확인하였다.

• Composites Research
• /
• 제23권4호
• /
• pp.7-13
• /
• 2010

체적 적분방정식법(Volume Integral Equation Method)이라는 새로운 수치해석 방법을 이용하여, 서로 상호작용을 하는 이방성 함유체를 포함하는 등방성 무한고체가 정적 인장하중을 받을 때 무한고체 내부에 발생하는 응력분포 해석을 매우 효과적으로 수행하였다. 즉, 등방성 기지에 다수의 이방성 함유체가 1) 정사각형 배열 형태 또는 2) 정육각형 배열 형태로 포함되어 있는 경우에 대하여, 다양한 함유체의 체적비에 대하여, 중앙에 위치한 이방성 함유체와 등방성 기지의 경계면에서의 인장응력 분포의 변화를 구체적으로 조사하였다. 또한, 단일의 이방성 함유체에 대한 체적 적분방정식법을 이용한 해와 해석해를 비교해 봄으로서, 체적 적분방정식법을 이용하여 구한 해의 정확도를 검증하였다.