• 한국산학기술학회논문지
• /
• 제7권6호
• /
• pp.1021-1027
• /
• 2006

엔진의 토크 변동과 추진축의 각속도 변화는 차량 동력 전달계의 주요 가진원이다. 본 논문에는 이들 가진원의 발생 기구에 대하여 논하였다. 이 시스템의 등가모델은 가진원과 유사하게 구성되었고, ARLA Simul v 6.7과 ARLA-Simstat v 2.3을 이용하여 컴퓨터 시뮬레이션을 수행하였다. 컴퓨터 시뮬레이션의 결과는 동력 전달계의 비틀림 가진원의 특성을 보였다. 엔진과 추진축 시스템에 대한 실험 장치는 차량의 부품으로 구성되었다. 플라이휠의 토크 변동과 추진축의 각속도는 실험 장치로 부터 측정하였다. 실험결과는 시뮬레이션 결과와 비교하였고, 이론적 결과와 일치하였다.

• 한국정밀공학회지
• /
• 제4권4호
• /
• pp.56-71
• /
• 1987

Determination of navigation variables (latitude, longitude, and altitude) near the earth's surface is termed 'Terrestrial Navigation'. The quantities that are measured inertially are the total acceleration (or the integral fo this acceleration over a fixed time interval) and the total angular rate (or the integral of this angular rate over the same time interval). These measurements when suitably compensated can be manipulated to yield the navigation variables. Hence, it is essential that the initial values of position, orientation and velocity are accurately set up during the initial alignment process. Initial alignment of gimballed inertial navigation system ( GINS) is accomplished by gyrocompassing techniques. These cannot be used, in the case of strapdown inertial navigation system(SDINS), where the inertial instruments are directly strapped down to a vehicle frame. The basic objective of this paper is the development of digital method for the determination of the initial axes erection of a SDINS from vibration and sway currupted data on the launch pad.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.786-791
• /
• 2006

Two stroke low speed diesel engines are mainly used for marine propulsion or power plant prime mover. These have many merits such as higher thermal efficiency, mobility and durability. However various annoying vibrations sometimes occur in ships or at the plant itself. Of these vibrations, torsional vibration is very important and it should be carefully investigated during the initial design stage for engine's safe operation. In this paper authors suggest a new estimation method of for shaft's can be calculated equivalently from accumulated fatigue cycles number due to torsional vibration. The 6S70MC-C($25,320ps{\times}91rpm$) engine for ship propulsion was selected as a case study, and the accumulated fatigue cycles numbers for shafting life time converted from the measured angular velocity and torsional vibration stress was calculated. This new method can be realized and confirmed in test model ship with two stroke low speed diesel engine.

• Steel and Composite Structures
• /
• 제32권2호
• /
• pp.225-237
• /
• 2019

In this research, the dynamic stability and nonlinear vibration behavior of a smart rotating sandwich cylindrical shell is studied. The core of the structure is a functionally graded material (FGM) which is integrated by functionally graded piezoelectric material (FGPM) layers subjected to electric field. The piezoelectric layers at the inner and outer surfaces used as actuator and sensor, respectively. By applying the energy method and Hamilton's principle, the governing equations of sandwich cylindrical shell derived based on first-order shear deformation theory (FSDT). The Galerkin method is used to discriminate the motion equations and the equations are converted to the form of the ordinary differential equations in terms of time. The perturbation method is employed to find the relation between nonlinear frequency and the amplitude of vibration. The main objective of this research is to determine the nonlinear frequencies and nonlinear vibration control by using sensor and actuator layers. The effects of geometrical parameters, power law index of core, sensor and actuator layers, angular velocity and scale transformation parameter on nonlinear frequency-amplitude response diagram and dynamic stability of sandwich cylindrical shell are investigated. The results of this research can be used to design and vibration control of rotating systems in various industries such as aircraft, biomechanics and automobile manufacturing.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.531-536
• /
• 2006

In four cylinder engine, the second order inertia force occurs due to the reciprocating parts of the cylinder. Because the magnitude of the inertia force is proportional to a square of the angular velocity of crank shaft, engine gets suffered from vibration excited by unbalanced inertia force in high speed. This vibration excited by the unbalanced inertia force can be canceled by applying a balance shaft. Balance shaft has one or more unbalance mass and rotates twice quickly than the crank shaft. In this paper, an unbalanced force caused by the rotating of unbalance mass of balance shafts was calculated. The directional equivalent stiffness and damping coefficients of the journal bearing of balance shafts was calculated. Equations of rotational vibration modes were derived using directional stiffness and damping coefficients. The dynamic stability of balance shafts was analyzed and evaluated for two type models using the equivalent stiffness and damping coefficients. An efficient procedure to he able to evaluate dynamic stability and design optimal balance shaft was proposed.

• 한국소음진동공학회논문집
• /
• 제16권1호
• /
• pp.57-65
• /
• 2006

In this paper, we present the principle of virtual work, from which the exact non-linear equations of motion of a rotating ring can be derived, by using the theory of finite deformation. For a thin ring of which the effect of variation in curvature across the cross-section is neglected, the radial displacement and the extensional stress are determined from the principle of virtual work at the steady state where the ring is rotating with a constant angular velocity. And also we formulate systematically the governing equations concerned to the in-plane vibrations and the out-of-plane vibrations at the disturbed state by using the principle of virtual work which is expressed with the disturbed displacements about the steady state. The formulated governing equations are classified by four models along the cases of considering or neglecting all or partly the secondary effects of flexural shear, rotary inertia, circumferential extension, and twist inertia. The natural vibrations of thin rings are analyzed, and its results are compared and discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.585-592
• /
• 2005

In this paper, we present the principle of virtual work, from which the exact non-linear equations of motion of a rotating ring can be derived, by using the theory of finite deformation For a thin ring of which the effect of variation in curvature across the cross-section is neglected, the radial displacement and the extensional stress are determined from the principle of virtual work at the steady state where the ring is rotating with a constant angular velocity. And also we formulate systematically the governing equations concerned to the in-plane vibrations and the out-of-plane vibrations at the disturbed state by using the principle of virtual work which is expressed with the disturbed displacements about the steady state. The formulated governing equations are classified by four models along the cases of considering or neglecting all or partly the secondary effects of flexural shear, rotary inertia, circumferential extension, and twist inertia. The natural vibrations of thin rings are analyzed, and its results are compared and discussed.

• 한국소음진동공학회논문집
• /
• 제19권2호
• /
• pp.208-216
• /
• 2009

In this paper, we present the equations of motion by which the natural vibration of a rotating annular disk can be analyzed accurately. These equations are derived from the theory of finite deformation and the principle of virtual work. The radial displacements of annular disk at the steady state where the disk is rotating at a constant angular velocity are determined by non-linear static equations formulated with 1-dimensional finite elements in radial direction. The linearlized equations of the in-plane vibrations at the disturbed state are also formulated with 1-dimensional finite elements in radial direction along the number of nodal diameters. They are expressed as in functions of the radial displacements at the steady state and the disturbed displacements about the steady state. In-plane static deformation modes of an annular disk are used as the displacement functions for the interpolation functions of the 1-dimensional finite elements. The natural vibrations of an annular disk with different boundary conditions are analyzed by using the presented model and the 3-dimensional finite element model to verify accuracy of the presented equations of motion. Its results are compared and discussed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.783-786
• /
• 1991

Generally, The position of mobile robot moving on the plane is measured by the method of dead reckoning, using the encoder system coupled on a wheel axis. But it is noted that the encoder system cannot check the slip of a wheel, often occurring in tracking of the mobile robot. In this study, using velocity angular velocity sensor with a tuning fork vibration system, the system is developed which can measure the directional angle of positional variables on the mobile robot. By measuring the variations of tracking direction mobile robot equipped with this system, following result is found; In spite of the slip at a wheel when measuring the tracking directional angle, the error occurs in the range of .+-. 1 (degree).

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.500-505
• /
• 2009

This paper presents temperature control of engine cooling system using a controllable magnetorheological (MR) fan clutch. An appropriate size of MR fan clutch is devised and modeled on the basis of Bingham model. Subsequently, an optimization to determine design parameters such as width of housing is undertaken by choosing the reciprocal of the controllable torque as an objective function. Under consideration of spatial limitation, design parameters are optimally determined using finite element analysis. A sliding mode controller is then designed to control the angular velocity of the MR fan clutch using experimentally determined parameters. The designed controller is experimentally implemented and control performances of the MR fan clutch system are evaluated.