• Journal of the Korean Wood Science and Technology
• /
• 제18권4호
• /
• pp.65-78
• /
• 1990

For the purpose of Improving the sounding boards for the conventional GAYAKUM, I was making approximately 202 specimens of radial board, 371 specimens of tangential board by cutting along the grain and the part of stem and 31 specimens of the disjointed traditional GAYAKUM made in Paulownia coreana. And it was conducted to measure specific gravity, dynamic Young's modulus, internal friction, resonant frequency, velosity of sound and width of annual ring by the method of the frexural vibration in a free-free bar in the audio frequency range. And it confirmed the juvenile wood by measuring wood fiber length of specimens. It was also conducted to investigate dynamic properties and moisture absorption by various heat-treatment and to test dynamic Young's modulus and internal friction for the disjointed conventional GAYAKUM. The results obtained were summarized as follow: 1. The Juvenile wood is located within about 7 annual rings from the pith in Paulownia coreana. 2. As increased with the specific gravity, the dynamic Young's modulus had more and more increased, but the internal friction had slightly decreased. 3. I think that radial board would be good for sounding board wood. because radial board is higher than tangential board in dynamic Young's mudulus and internal friction is lower than tangential board. 4. The value of mean dynamic Young's modulus on the conventional GAYAKUM, radial board and tangential board of 604 samples is $0.4283\pm0.037(\times10^{11}dyne/cm^2)$, $0.4316\pm(\times10^{11}dyne/cm^2)$ and $0.4234\pm0.112(\times10^{11}dyne/cm^2)$ respectively. The value of the radial board showed little higher than that of conventional GAYAKUM, but It had a similar tendency between conventional GAYAKUM and tangential board. 5. The annual ring width by four aspect is more narrow in north and west than that of others. 6. The values of specific gravity and dynamic Young's modulus in the mature wood showed higher than those of juvenile wood. 7. As the grain angle in the butt wood more increased to bark from pith, the dynamic Young's modulus were low. Then it was not good for sounding board. 8. It appeared that the heat-treatment for sounding board wood had a more effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature. 9. As increased with the temperature, the rate of moisture absorption of heat-treatment wood had decreased. In conclusion, I thought that the sounding board wood for GAYAKUM would had the most effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature using the radial board of mature wood.

• 동력기계공학회지
• /
• 제4권1호
• /
• pp.26-32
• /
• 2000

Single-phase heat transfer performance and pressure drop for internally grooved tubes with angles were studied. Experiments were carried out in a counter flow heat exchanger with water as a working fluid. Two commercially available internally grooved tubes and smooth tube were tested. The internal diameter of the smooth tube was 16.5mm and the internal diameters of grooved tubes were 15.4mm, 14.9mm, 15.0mm, 16.7mm, respectively. Grooved angles in the tubes were $37^{\circ},\;43^{\circ},\;45^{\circ},\;50^{\circ}$, respectively. An experimental device to measure the friction factor and heat transfer coefficient was constructed. The experimental results were obtained for the fully developed turbulent flow of water in tube on the condition of uniform heat flux. As the increase of flow rate, Reynolds number, numbers of groove and grooved angle led to the increase of pressure drop. Also this paper showed that heat transfer rate increased with increasing numbers of groove and grooved angle. An empirical relation taken from this study represented most of the data within ${\pm}25%$.

• 한국지반환경공학회 논문집
• /
• 제7권5호
• /
• pp.31-39
• /
• 2006

일반적으로 흡수력은 불포화 흐름과 전단강도상의 거동을 평가하기 위한 중요한 인자가 되며, 불포화토의 부 간극수압은 흙의 구조와 포화도에 의해 영향을 받는다. 본 연구에서는 불포화 준설토의 전단강도 특성을 조사하기 위해 수정된 삼축압축시험이 수행되었다. 실험결과로서 전단강도의 변화는 배수조건보다 흡수력에 더 영향을 받고 있음을 알 수 있었고 점차적으로 흡수력 100 kPa에 수렴되고 있음을 보여준다. 이것은 흙의 불포화 상태에서 내부마찰각과 점착력이 포화상태에 비하여 흡수력에 기인하여 증가하고 있음을 나타내며, 불포화토에서 합리적인 지반강도정수의 산정을 위해서는 흡수력의 변화에 따른 겉보기 마찰각 ${\phi}^b$이 고려되어야 함을 알 수 있다.

• 한국지반공학회논문집
• /
• 제38권2호
• /
• pp.5-13
• /
• 2022

불포화토의 전단 특성 평가는 사면, 제방, 댐 등의 안정성과 투수 특성 평가에 매우 중요한 요소이다. 본 연구에서는 화강풍화토의 불포화 전단특성을 파악하기 위하여 불포화 삼축실험을 수행하였다. 실험에 사용된 시료는 국내에 분포하는 세립분이 다량함유된 SM계열 화강 풍화토이며, 다짐을 통하여 재성형 하였다. 모관 흡수력 및 시료의 밀도에 따른 불포화 전단 특성을 분석하였으며, 전단 과정에서 일정한 모관 흡수력을 유지 하기 위해 압밀-배수삼축실험(CD-test)을 수행하였다. 본 연구결과 화강풍화토 시료의 겉보기마찰각(ϕ^b)과 AEV(Air Entry Value)는 상대밀도가 증가함에 따라 증가하는 경향을 나타내었다. 그러나 모관흡수력이 증가함에 따라서는 점착력(c) 역시 증가하였지만 내부마찰각(ϕ')은 크게 변함이 없는 것으로 확인 되었다.

• Structural Engineering and Mechanics
• /
• 제52권6호
• /
• pp.1225-1256
• /
• 2014

Calculating the seismic displacement of retaining walls has an important role in the optimum design of these structures. Also, studying the effect of surcharge is important for the calculation of active pressure as well as permanent displacements of the wall. In this regard, some researchers have investigated active pressure; but, unfortunately, there are few investigations on the seismic displacement of retaining walls with surcharge. In this research, using limit analysis and upper bound theorem, permanent seismic displacement of retaining walls with surcharge was analyzed for sliding and overturning failure mechanisms. Thus, a new formulation was presented for calculating yield acceleration, critical angle of failure wedge, and permanent displacement of retaining walls with surcharge. Also, effects of surcharge, its location and other factors such as height of the wall and internal friction angle of soil on the amount of seismic displacements were investigated. Finally, designing charts were presented for calculating yield acceleration coefficient and angle of failure wedge.

• Geomechanics and Engineering
• /
• 제23권5호
• /
• pp.481-491
• /
• 2020

Piles installed in row(s) are used as an effective technique to improve the stability of soil slopes. The analysis of pile-stabilized slopes require a reliable prediction of lateral resistance offered by the piles. In this work, an analytical solution is developed to estimate the lateral resistance offered by the stabilizing piles in sand and c - 𝜙 soil slopes considering soil arching phenomenon. The soil arching in both horizontal direction (between the neighboring piles) and vertical direction (in the active wedge in front of the pile row) are studied and their effects are incorporated in the proposed model. The shape of soil arch is assumed to be circular and principal stress trajectories are defined separately for both modes of arching. Experimental and numerical studies found in literature were used to validate the proposed method. A detailed parametric analysis was performed to study the influence of pile diameter, center-to-center spacing, slope angle and angle of internal friction on the lateral pile resistance.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.139-145
• /
• 1996

Tapping is one of the most widely used machining operations. There are several methodes of producing external screw threads, e.g. turning, milling with single or multiple cutter, rolling, and grinding, but the methods available for cutting enternal threads are less numerous, and for threads in small holes, tapping is employed almost exclusively. In this study, the tap with the various geometry has been developed in order to tap special workmaterial at considerably higher cutting speed than that of the conventional HSS tap. The experimental tests are run with various cutting speed by using a piezo type tool dynamometer to measure tapping torque. Tapping torque is affected by the design of the tap, which seems to be due to internal friction and shearing of the metal. It is clarified that the process of chip formation strongly depends on rake angle, relief angle, angle of twist.

• Geomechanics and Engineering
• /
• 제28권6호
• /
• pp.585-598
• /
• 2022

The monopile-friction wheel hybrid foundation is an innovative solution for offshore structures which are mainly subjected to large lateral eccentric load induced by winds, waves, and currents during their service life. This paper presents an extensive numerical analysis to investigate the lateral load and moment bearing performances of hybrid foundation, considering various potential influencing factors in sand-overlaying-clay soil deposits, with the complex lateral loads being simplified into a resultant lateral load acting at a certain height above the mudline. Finite element models are generated and validated against experimental data where very good agreements are obtained. The failure mechanisms of hybrid foundations under lateral loading are illustrated to demonstrate the effect of the friction wheel in the hybrid system. Parametric study shows that the load bearing performances of the hybrid foundation is significantly dependent of wheel diameter, pile embedment depth, internal friction angle of sand, loading eccentricity (distance from the load application point to the ground level), and the thickness of upper sandy layer. Simplified empirical formulae is proposed based on the numerical results to predict the corresponding lateral load and moment bearing capacities of the hybrid foundation for design application.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.1083-1090
• /
• 2005

Repeated ribs are used on heat exchange surfaces to promote turbulence and enhance convective heat transfer. Applications include fuel rods of gas-cooled nuclear reactors, inside cavities of turbine blades, and internal surfaces pipes used in heat exchangers. Despite the great number of literature papers, only few experimental data concern detailed distributions of friction factors and heat transfer coefficients in square channels varying the number of rough walls. This issue is tackled by investigating effects of different number of ribbed walls on heat transfer and friction characteristics in square channel. The rough wall have a 45$^{\circ}$ inclined square rib. Uniform heat flux is maintained on whole inner heat transfer channel area. The heat transfer coefficient and friction factor values increase with increasing the number of rough walls.

• 한국자동차공학회논문집
• /
• 제18권3호
• /
• pp.37-42
• /
• 2010

Plastic region tightening is widely used in critical bolted joints in internal combustion engines in order to reduce the engine weight by maximizing the use of load-carrying capacity of bolt. Mechanical behavior of bolt tightened in plastic region under external axial tensile load is investigated for various friction conditions using three dimensional finite element analysis. The behavior of bolt tightened in elastic region as well as that in tensile test are investigated for comparison. Tightening process is simulated by rotating the bolt in order to examine the friction effect realistically. It is revealed that the bolt tightened in plastic region can carry more external load until the joint is opened, and yields at lower bolt load than the bolt tightened in elastic region. The friction coefficient has effect on the yield load, but not on the load-carrying capacity. Moreover, the scatter in the bolt preload due to friction begins with plastic deformation of bolt in the angle tightening control, whereas it begins with the onset of tightening in the torque tightening control. The observations are interpreted with the residual torsional stress in the bolt generated during the tightening.