• Journal of the Korea Institute of Military Science and Technology
• /
• v.16 no.3
• /
• pp.365-372
• /
• 2013

The multibeam surveillance radar is a state-of-art of 3D radar technology. It applies the stacked beams realized by a digital beamformer. In this paper, a hybrid compensation technique on elevation angle errors for low elevation angle targets over the sea in multipath radar environments is proposed. The proposed method can be applied to stacked beam radars. Double null algorithm based on maximum likelihood method in 3-D beamspace domain works well unless the phase difference between the two rays(direct and specular path) is close to $0^{\circ}$ and the magnitude of reflection coefficient is close to 0. To overcome these problems, we propose a hybrid compensation technique which uses the selective double null algorithm and the beam-ratio compensation technique for low-elevation errors on a log scale. Results of computer simulation show that the proposed method outperform conventional monopulse method and double null algorithm only under various multipath environments.

• Journal of the Society of Naval Architects of Korea
• /
• v.50 no.3
• /
• pp.190-198
• /
• 2013

In order to predict acoustic pressure distributions by exterior incident wave at Cylindrical Hydrophone Array (CHA) sensor's positions, acoustic pressure analysis is performed by using beam tracing method. Beam tracing method is well-known of reliable pressure analysis methods at high-frequency range. When an acoustic noise source is located at the center of rectangular room, acoustic pressure analysis is performed by using both beam tracing method and Power Flow Boundary Element Method (PFBEM). By comparing with results of beam tracing method and those of PFBEM, the accuracy of beam tracing method is verified. We develop the CHA pressure analysis program by verified beam tracing method. The developed software is composed of model input, sensor array creator, analysis option, solver and post-processor. We can choose a model option of 2D or 3D. The sensor array generator is connected to a sonar which is composed of center position, bottom, top and angle between sensors. We also can choose an analysis option such as analysis frequency, beam number, reflect number, etc. The solver module calculates the ray paths, acoustic pressure and result of generating beams. We apply the program to 2D and 3D CHA models, and their results are reliable.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.142-150
• /
• 1996

Monopulse technique has been widely used for a bearing estimation of a desired signal. This method can estimate the bearing of the signal with only one pulse, so computational load and complexity are low and its processes are simple. But if the desired signal incidents with interferences or multiple signals exist in the beams, the method fails to estimate correct signal angle. To solve this problem, the method to use adaptive array was proposed. In conventional adaptive array methods, sum beam was formed with fixed weights and ifference beam was formed with adaptive weights determined to minimize beamformer output power with one or more linear constraints, or an algorithm to minimize each sum beam and difference beams simultaneously using adaptively formed one basic beam. Theroretical analyses and simulation results show that the performance of the proposed method is superior to that of conventional algorithms.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.12
• /
• pp.1747-1755
• /
• 2002

A complete theoretical treatment of the photothermal displacement technique has been performed for thermal diffusivity measurement in semi-infinite solid materials. The influence of the parameters, such as radius and modulation frequency of the heating beam and the thermal diffusivity, was studied. Usually, thermal diffusivity was determined by the deformation angle and phase angle as the relative position between the heating and probe beams. In this study, we proposed the simple analysis method based on the real part of deformation gradient as the relative position between two beams. It is independent in the parameters such as power of heating beam, absorption coefficient, reflectivity, Poisson's ratio, and thermal expansion coefficient.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.9
• /
• pp.1070-1077
• /
• 2011

This study intends to assess the defect in the weld zone of titanium grade 2 plate in terms of acoustical anisotropy based on the angle beam method. Depending on the rolling direction, the ratio of wave velocity was found to be 1.08 and the difference in the angle of refraction was more than seven degrees, confirming the presence of acoustical anisotropy. Thus for measuring the length of defect in the weld zone of the titanium plate (thickness of 10mm), the distance amplitude characteristics curves of titanium, TDACC-R and TDACC-T were constructed for the measurements in consideration of the acoustical anisotropy on CRT of the ultrasonic testing equipment. As a result, when the distance amplitude characteristics curve corresponds to the rolling direction, the length of defect was close to the actual measurement within 1mm and when different, the difference was found to be over 4mm. It was affirmed that the acoustical anisotropy should be taken into consideration when measuring the length of defects in the weld zone of the titanium plate with the presence of acoustical anisotropy.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.760-763
• /
• 2004

We studied the nematic liquid crystaL(NLC) aligning capabilities using the new alignment material of a nitrogenated diamond-like carbon(NDLC) thin film. The NDLC thin film exhibits high electrical resistivity and thermal conductivity that are similar to the properties shown by diamond-like carbon (DLC) thin films. The diamond-like properties and nondiamond-like bonding make NDLC an attractive candidate for applications. A high pretilt angle of about 9.9$^{\circ}$ by ion beam(IB) exposure on the NDLC thin film surface was measured. A good LC alignment is achieved by the IB alignment method on the NDLC thin films surface at annealing temperature of 200 $^{\circ}C$. The alignment defect of the NLC was observed above annealing temperature of 250 $^{\circ}C$. Consequently, the high pretilt angle and the good LC alignment by the IB alignment method on the NDLC thin film surface can be achieved.

• Earthquakes and Structures
• /
• v.16 no.1
• /
• pp.83-96
• /
• 2019

The seismic behavior of PRC coupling beam-hybrid coupled shear wall system is analyzed by using the finite element software ABAQUS. The stress distribution of steel plate, reinforcing bar in coupling beam, reinforcing bar in slab and concrete is investigated. Meanwhile, the plastic hinges developing law of this hybrid coupled shear wall system is also studied. Further, the effect of coupling ratio, section dimensions of coupling beam, aspect ratio of single shear wall, total height of structure and the role of slab on the seismic behavior of the new structural system. A fitting formula of plate characteristic values for PRC coupling beams based on different displacement requirements is proposed through the experimental date regression analysis of PRC coupling beams at home and abroad. The seismic behavior control method for PRC coupling beam-hybrid coupled shear wall system is proposed based on the continuous connection method and through controlling the coupling ratio, the roof displacement, story drift angle of hybrid coupled shear wall system, displacement ductility of coupling beam.

• Structural Engineering and Mechanics
• /
• v.13 no.3
• /
• pp.345-353
• /
• 2002

Three noded plate and shell finite element and 3D beam element in conjunction with Lanczos method are used for studying the effect of boat tail angle on the free vibration characteristics of a typical payload fairing for three different cylinder diameters with height to diameter ratio 1.5. Configurations without boat tail structural member are also studied. One half of the one side fairing structure is considered for the analysis and symmetric boundary conditions are used.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2001.10a
• /
• pp.477-483
• /
• 2001

Optimum directivity synthesis of ultrasonic transducers in linear array is considered. To realize the desired directivity, a robust and efficient method is proposed which is the direct inversion combined with the iterative DFP (Davidon-Fletcher-Powell) method. A quasi-ideal beam with the beam width and the steering beam angle specified are chosen for the numerical demonstrations. The demonstration is then extended to the case of multi-beams. The proposed combination method shows quick convergence over the single LMS or DFP method at the expense of the system matrix inversion.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.04a
• /
• pp.61-64
• /
• 2003

The finite element method based on the refined beam theory is applied to the vibration problem of rotation composite box beams. The present beam model includes a number of non-classical structural effects such as transverse shear, warping deformations, geometric non-linearities. The nonlinear finite element equations of motion are obtained from Hamilton's principle. Vibration characteristics versus various parameters such as ply angle, collective pitch angle, pretwist and precone are investigated for rotation box ben and relevant conclusions are outlined.