• Advances in Energy Research
• /
• v.1 no.1
• /
• pp.35-52
• /
• 2013

A model for DMFC anode performance is developed. The model takes into account potential--independent methanol adsorption on the catalyst surface, finite rate of proton transport through the anode catalyst layer (ACL), and a potential loss due to methanol transport in the anode backing layer. An approximate analytical half--cell polarization curve is derived and equations for the anode limiting current density are obtained. The polarization curve is fitted to the curves measured by Nordlund and Lindbergh and parameters resulted from the fitting are discussed.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2001.09a
• /
• pp.227-234
• /
• 2001

The responses of a 1:5 scale 3-story masonry-infilled RC frame which was designed only for gravity loads were simulated by using a nonlinear analysis program, DRAIN-2DX The objective of this study is to verify the correlation between the experimental and analytical responses of masonry-infilled RC frame. It is concluded from this comparison that the strength and stillness of the whole structure can be predicted with quite high reliability using compressive strut (compression link element, Type 09) while some local behavior cannot be described reasonably.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.211-214
• /
• 2005

The analytical model capable of predicting stress vs. strain relations for circular FRP-confined concrete in a rational manner is proposed. The underlying idea is that the volumetric expansion due to progressive microcracking is an important measure of the extent of damage in the material microstructure. Various existing analytical models including the proposed were also investigated, and compared each other and with test results.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.660-665
• /
• 2003

The true stress - true strain relation of SA508 steel was evaluated with analytical and experimental equation on the base of the indentation load-depth curve obtained from the modeling of ball indentation test. The evaluated relation between true stress and true strain is agreed well with that of SA508 teel defined in the modeling. The distribution of effective stress along the center axis of indentation depth was calculated with Tresca criteria in the modeling. The representative strain, which are defined in this study as the corresponding strains obtained from the maximum effective stress, have a linear relation with the true strain. The true stress - true strain relation of austenitic stainless steel was evaluated by the modeling of ball indentation test to verify the case of A508 steel.

• Proceedings of the KIEE Conference
• /
• 1997.07b
• /
• pp.590-592
• /
• 1997

A Discrete Event Dynamic System is a system whose states change in response to the occurrence of events from a predefined event set. A major difficulty in developing analytical results for the systems is the lack of appropriate modeling techniques. This paper proposes the use of Real-time Temporal Logic as a modeling tool for the analysis and control of DEDS. The Real-time Temporal Logic Frameworks is extended with a suitable structure of modeling hard real-time constraints. Modeling rules are developed for several specific situations. It is shown how the graphical model can be translated to a system of linear equations and constraints.

• Tunnel and Underground Space
• /
• v.34 no.2
• /
• pp.127-142
• /
• 2024

The robustness of a numerical method means that its computational performance is maintained under various modeling conditions. New numerical methods or codes need to be assessed for robustness through benchmark testing. The TOUGH-FLAC modeling approach has been applied to various fields such as subsurface carbon dioxide storage, geological disposal of spent nuclear fuel, and geothermal development both domestically and internationally, and the modeling validity has been examined by comparing the results with experimental measurements and other numerical codes. In the present study, a benchmark test of the TOUGH-FLAC approach was performed based on a coupled thermal-hydro-mechanical behavior problem with an analytical solution. The analytical solution is related to the temperature, pore water pressure, and mechanical behavior of a fully saturated porous medium that is subjected to a point heat source. The robustness of the TOUGH-FLAC approach was evaluated by comparing the analytical solution with the results of numerical simulation. Additionally, the effects of thermal-hydro-mechanical coupling terms, fluid phase change, and timestep on the computation of coupled behavior were investigated.

• Geophysics and Geophysical Exploration
• /
• v.4 no.3
• /
• pp.70-79
• /
• 2001

The integral equation method is a powerful tool for numerical electromagnetic modeling. But the difficulty of this technique is the size of the linear equations, which demands excessive memory and calculation time to invert. This limitation of the integral equation method becomes critical in inverse problem. The conventional Born approximation, where the electric field in the anomalous body is approximated by the background field, is very rapid and easy to compute. However, the technique is inaccurate when the conductivity contrast between the body and the background medium is large. Quasi-linear, quasi-analytical and extended Born approximations are novel approaches to 3-D EM modeling based on the linearization of the integral equations for scattered EM field. These approximation methods are much less time consuming than full integral equation method and more accurate than conventional Born approximation. They we, however, still approximate methods for 3-D EM modeling. Iterative series methods such as modified Born, quasi-linear and quasi-analytical can be used to increase the accuracy of various approximation methods. Comparisons of numerical performance against a full integral equation and various approximation codes show that the iterative series methods are very accurate and almost always converge. Furthermore, they are very fast and easy to implement on a computer. In this study, extended Born series method is developed and it shows more accurate result than that of other series methods. Therefore, Iterative series methods, including extended Born series, open principally new possibilities for fast and accurate 3-D EM modeling and inversion.

• Structural Engineering and Mechanics
• /
• v.64 no.1
• /
• pp.81-92
• /
• 2017

Many materials in engineering exhibit different modulus in tension and compression, which are known as bi-modulus materials. Based on the bi-modulus elastic theory, a modified semi-analytical model, by introducing a stress function, is established in this paper to study the mechanical response of a bi-modulus cylinder placed in an axisymmetric temperature field. Meanwhile, a numerical procedure to calculate the temperature stresses in bi-modulus structures is developed. It is proved that the bi-modulus solution can be degenerated to the classical same modulus solution, and is in great accordance with the solutions calculated by the semi-analytical model proposed by Kamiya (1977) and the numerical solutions calculated both by the procedure complied in this paper and by the finite element software ABAQUS, which demonstrates that the semi-analytical model and the numerical procedure are accurate and reliable. The result shows that the modified semi-analytical model simplifies the calculation process and improves the speed of computation. And the numerical procedure simplifies the modeling process and can be extended to study the stress field of bi-modulus structures with complex geometry and boundary conditions. Besides, the necessity to introduce the bi-modulus theory is discussed and some suggestions for the qualitative analysis and the quantitative calculation of such structure are proposed.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.69-80
• /
• 1999

Computer simulations have played a central role in the development of out understanding of the atomic scale processes involved in crystal growth. The assumptions underlying computer modeling will be discussed and out recent work on modeling of the kinetic formation of thermodynamically unstable phases in alloys or mixtures will be reviewed. Our Monte Carlo computer simulations have reproduced the experimental results on the rapid recrystallization of laser-melted doped silicon. An analytical model for this phenomenon has been developed, and its applicability to other materials will be discussed.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.434-437
• /
• 1999

The primary aim of this paper is to introduce and illustrate a radial basis function (RBF) modeling approach fur software module characterization, as an alternative to current techniques. The RBF model has been known to provide a rich analytical framework fur a broad class of so-called pattern recognition problems. Especially, it features both nonlinearity and linearity which in general are treated separately by its learning algorithm, leading to offer conceptual and computational advantages. Furthermore, our new modeling methodology fer determining model parameters has a sound mathematical basis and showed very interesting results in terms of model consistency as well as performance.