• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.44 no.4
• /
• pp.362-369
• /
• 2008

The snow melting system by electric heating wires which is adopted in this research is a part of road facilities to keep surface temperature of the road higher than freezing point of water for melting the snow accumulated on it. The electric heating wires are buried under paved road at a certain depth and operated automatically and manually. Design theory, amount of heating, and installation standard vary according to economic situation, weather condition, installation place and each country applying the system. A main purpose of this study is figuring out the appropriate range of required heat capacity and installation depth and pitch for solving snowdrifts and freezing problems with minimum electric power consumption. This study was performed under the ambient air temperature($-2^{\circ}C$, $-5^{\circ}C$), the pitches of the electric heating wires(200 mm, 300 mm), heating value($250\;W/m^2$, $300\;W/m^2$, $350\;W/m^2$).

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.1-4
• /
• 2008

Fuel cells have the potential of providing several times higher energy storage densities than those possible using current state-of-the-art lithium-ion batteries, but current energy density of fuel cell system is not better than that of lithium-ion batteries. To achieve the high energy density, volume and weight of fuel cell system need to be reduced by miniaturizing system components such as stack, fuel tank, and balance-of-plant. In this paper, the thin flexible PCB (Printed circuit board) is used as a current collector to reduce the stack volume. Two end plates are made from light weight aluminum alloy plate. The plate surface is wholly oxidized through the anodizing treatment for electrical insulation. The opening rate of cathode plate hole is optimized through unit cell performance measurement of various opening rates. The performances are measured at room temperature and ambient pressure condition without any repulsive air supply. The active area of MEA is 10.08 $cm^2$ and active area per a unit cell is 1.68 $cm^2$. The peak power density is about 210 mW/$cm^2$ and the air-breathing planar stack of 2 Wis achieved as a small volume of 18 cc.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.153-157
• /
• 2009

A Highly efficient Mercury-free Flat Fluorescent Lamp (MFFL) with dielectric barrier Xe gas discharge was developed for an alternative of conventional line-type Cold Cathode Fluorescent Lamps (CCFLs) which shows a wide voltage margin and a stable discharge operation for diffuse glow discharge with an application of a auxiliary electrode. Electro-optic characteristics of the MFFL were examined through the changes in ambient temperature, total pressure and Xe partial pressure. the single cell is expanded into a multi-structured configuration to realize a large sized lamp by a simple repetition of the single cells, and a new driving scheme is proposed for an adaptive brightness control using dual auxiliary electrodes and bi-polar drive scheme. In addition, interesting application of this ultra high luminance flat lamp by the optimization of the gas condition and the pattern of the rear phosphor layer is suggested as a good alternative of daylight lamp source

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.4
• /
• pp.313-319
• /
• 2001

The development of ozone SRP (Standard Reference Photometer) designated as a G-7 project by the Korean Ministry of Environment began 1997 and is now nearly completed. With the completion of the ozone SRP we will not only acquire a qualification to participate in the international ozone calibration system but also enhance calibration credibility of ozone similarly to that of other ambient air pollution monitors. As the ozone SRP uses highly cleaned blank air that can be distinguished from general ozone analyzer, it is possible to reduce errors associated with the determination of ozone via elongation of the absorption length as long as 1 meter In addition, gas chopping method hat been adopted to cut down interference of other substances and time drift. Furthermore, the system has also been modified to minimize the strayed ultra-violet noise along the light path. In this paper, a new method for uncertainty evaluation has been introduced, which is guided by the ISO (International Standard Organization) GUM (Guide to the Expression of Uncertainty in Measurement) through assessments of the uncertainty type B (that was impossible to estimate before) as well as the uncertainty type A (based on statistics).

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.347-350
• /
• 2003

Pleurotus eryngii is one of the most promising mushrooms produced on the domestic farms. The quality as well as quantity of Eryngii is sensitively affected by micro climate factors such as temperature, relative humidity, $CO_2$ concentration, and light intensity. At the commercial mushroom cultivation houses, this study was carried out to find out reasonable range of each environmental factor and yield together with economic and safe structures influencing on the optimal productivity of Eryngii. This experiment was conducted from Jan. 26, 2003 to Aug. 2, 2003. Ambient temperature during the experiment period was not predominantly different from that of a normal year. The capacity of the hot water boiler and the piping systems were not enough. Maximum temperature difference between the upper and lower growth stage during a heating time zone was about $6^{\circ}C$. The max. and min. relative humidity were ranged approximately $42{\sim}100%$. The $CO_2$ concentration and the illuminance were lowly maintained during growing period. The average yield per bottle was about $54{\sim}102g$.

• Asian Journal of Atmospheric Environment
• /
• v.4 no.1
• /
• pp.9-19
• /
• 2010

The size distribution of airborne particulate matter (PM) and the concentrations of associated metallic elements were investigated in a busy urban region of a typical Korean industrial city. The PM concentrations measured during the spring, except for those in the size range of 1.1 to 2.1 ${\mu}m$, were slightly higher than the PM concentrations in the summer. Coarse particles contributed greatly to the variation in PM concentrations in the spring, while fine and submicron particles contributed largely to the variation in PM concentrations in the summer. The difference in size modes of the PM concentrations between spring and summer may be explained by the Asian dust effect and its accompanying wind direction and speed. Extremely high enrichment factors (EFs) values (6,971 to 60,966) for all of the size distributions in PM were identified for cadmium (Cd). High EFs values (12 to 907) were also identified for other heavy metals including Cr, Cu, Ni, Pb, Zn and Mn. Low EF values (0.29 to 8.61) were identified for Ca, K, Mg and Na. These results support the common hypothesis that most heavy metals in ambient PM have anthropogenic sources and most light metals have crustal sources. The results of principal components analyses and cluster analyses for heavy metals indicate that the principal sources of PM and metals were emissions from non-ferrous metal smelters, oil combustion, incinerators, vehicular traffic and road dust.

• Transactions on Electrical and Electronic Materials
• /
• v.5 no.3
• /
• pp.93-97
• /
• 2004

Structural and optoelectronic properties of as-synthesized SnO$_2$ nanowires were examined in this study. The SnO$_2$ nanowires were first synthesized by thermal evaporation of ball-milled SnO$_2$ powders in argon atmosphere without the presence of any catalysts, arid their structural properties are then investigated by X-ray diffraction, Raman scattering, scanning electron microscopy, and transmission electron microscopy. This investigation revealed that the synthesized SnO$_2$ nanowires are single-crystalline and that their growth direction is parallel to the [100] direction. In addition, photoresponse of a single SnO$_2$ nanowire was performed with light with above-gap energy, and different characteristics of photoresponses were obtained for the nanowire at ambient atmosphere and in vacuum. The photoresponse mechanism is briefly discussed in this paper.

• Journal of Digital Contents Society
• /
• v.18 no.1
• /
• pp.123-132
• /
• 2017

The physical display technology is the ultimate display technology that human beings aspire, and the world makes use of laser, plasma and reflector plate. Besides, technology development of binocular stereoscopic display has been actively progressed, but there is a limitation to the intact physical representation such as influence of optical ambient light and brightness. In this paper, the display technology using physical deformation different from the existing optical display is approached as a cultural and emotional perspective. The purpose of this paper is to develop the multivariate display technology that can create 3D realistic stereoscopic images through projecting dynamic images on physically diversified screen by overcoming the limitations of 2D planar digital signage and study how to apply them to video, exhibition and performance.

• Journal of Information Display
• /
• v.3 no.1
• /
• pp.11-16
• /
• 2002

This paper presents a study on the tubeless Plasma Display Panel (PDP) packaging using glass-to-glass electrostatic bonding with intermediate amorphous silicon. The bonded sample sealing the mixed gas with three species showed high strength ranging from 2.5 MPa to 4 MPa. The glass-to-glass bonding for packaging was performed at a low temperature of $180^{\circ}C$ by applying bias of 250 $V_{dc}$ in ambient of mixed gases of He-Ne(27 %)-Xe(3 %). The tubeless packaging was accomplished by bonding the support glass plate of $30mm{\times}50mm$ on the rear glass panel and the capping glass of $20mm{\times}20mm$. The 4-inch color AC-PDP with thickness of 8 mm was successfully fabricated and fully emitted as white color at a firing voltage of 190V.

• Journal of ILASS-Korea
• /
• v.7 no.4
• /
• pp.32-41
• /
• 2002

The breakup characteristics of liquid sheets formed by like-doublet injector were investigated in the cold-flow and atmospheric ambient pressure condition. The sheet breakup wavelength, which induces the sheet to be broken into ligaments, as well as the sheet breakup length, which is important for the flame location, was measured using a stroboscopic light. The liquid ligaments are formed intermittently after the breakup of sheet, and the wavelength of ligaments has been believed to have a relation to the combustion instability of liquid rocket engine. Therefore, the wavelength of ligaments and the breakup length of ligaments into fine drops were also measured. Since these spray characteristics are affected by the flow characteristics of two liquid jets before they impinge on each other, we focused on the effects of orifice internal flow such as the cavitation phenomenon that occurs inside the sharp-edged orifice. From the experimental results, we found that the liquid jet turbulence delays the sheet breakup and makes shorter wavelengths for both sheets and ligaments. Since the turbulent strength of sharp-edged orifice is stronger than that of round-edged orifice, the shape of orifice entrance results in large differences in the spray characteristics. Using these results, we proposed empirical models on the spray characteristics of the like-doublet injector, and these models are believed to provide some useful and actual data for designing liquid rocket combustors.