• 한국유체기계학회 논문집
• /
• 제19권2호
• /
• pp.27-35
• /
• 2016

The purpose of this study is to develop a method to predict the performance and economics of a micro gas turbine cogeneration system using performance correction curves. The variables of correction curves are ambient temperature, ambient pressure, relative humidity and load fraction. All of the values of correction factors were expressed as relative values with respect to design values at the ISO conditions. Once the correction curves are obtained, system performance can be predicted relatively easily compared to a detailed performance analysis method through a simple multiplication of the correction factors of various variables at any operating conditions. The predicted results using the correction curve method were compared with those by the detailed and more complex performance analysis in a wide operating range, and its feasibility was confirmed. To illustrate the usability of the correction curve method, the results of an economic analysis of a cogeneration system considering varying operating ambient condition and load was presented.

• 한국자동차공학회논문집
• /
• 제2권6호
• /
• pp.102-109
• /
• 1994

As a fundamental study to apply high pressure injection system to direct injection diesel engine, fuel injection system and constant volume combustion chamber were made and the behaviors of evaporating spray with the variation of injection pressure and the ambient gas temperature were observed by using high speed camera, and the combusion characteristics with the variation of injection pressure and A/F ratio were analyzed. As injection pressure increases, spray tip penetration and spray angle increase and, as a results spray volume increases. This helps an uniform mixing of fuel and air. Spray liquid core length decreases as ambient gas temperature increases, while it decreases as injection pressure increases but the effect of ambient gas temperature is dorminant. As injection pressure increases, ignition delay is shortened and combustion rate being raised, maximum heat release rate increases. It become clear that High injection pressure has high level of potential to improve the performance of DI-diesel engine.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.10-11
• /
• 2006

The use of hot gas in melt atomization has been widely reported, but little detailed experimental data on its precise effects and no satisfactory theory to explain them have been published. In this paper the authors present experimental data on the atomization of metals with gas at temperatures from ambient to 1000C, a semi-empirical equation relating particle size to gas temperature and flow rate, and an analysis of the gas dynamics of the atomization process that allows some insight into the process.

• 한국전기전자재료학회논문지
• /
• 제20권3호
• /
• pp.263-267
• /
• 2007

We investigate the influence of the ambient gas during thermal annealing on the photoluminescence (PL) properties of europium-silicate thin films. The films were fabricated on substrates by using a radio-frequency magnetron sputtering method and subsequent rapid thermal annealing (RTA). The mechanism for the formation of the europium silicates during the annealing process was investigated by using X-ray diffraction (XRD) spectroscopy, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A series of narrow PL spectra from $Eu^{3+}$ ions was observed from the film annealed in $O_2$ ambient. Broad PL spectra associated with $Eu^{2+}$ ions, with a maximum intensity at 600 nm and a FWHM of 110 nm, were observed from the thin film annealed at $1000^{\circ}C$ in $N_2$ ambient.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.124-131
• /
• 2007

The numerical study on behavior of impinging spray from high-pressure swirl injector under various ambient temperatures was performed by using spray vaporization model and spray-wall impingement model implemented in modified KIVA code, and these spray models were estimated by comparison with experimental results. To compute the spray-wall impingement process, the Gosman model, which is based on the droplet behavior after impingement determined by experimental correlations, was used. The modified Abramzon and Sirignano model, that includes the effects of variable thermodynamic properties and non-unitary Lewis number in the gas film, was adapted for spray vaporization process. The exciplex fluorescence measurements were also conducted for comparison. The experimental and numerical analysis were carried out at the ambient pressures of 0.1 MPa and at the ambient temperature of 293 K and 473 K, and the spray characteristics, such as spray-wall impingement process, gas velocity field, SMD and vapor concentration, were acquired. It was found that the impinging spray develops active and SMD is small at vaporization conditions.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.418-419
• /
• 2006

We investigate the influence of the ambient gas during thermal annealing on the photoluminescence (PL) properties of europium-silicate thin films. The films were fabricated on substrates by using a radio-frequency magnetron sputtering method and subsequent rapid thermal annealing (RTA). The mechanism for the formation of the europium silicates during the annealing process was investigated by using X-ray diffraction (XRD) spectroscopy, Auger electron spectroscopy (AES) and transmission electron microscopy (TEM). A series of narrow PL spectra from $Eu^{3+}$ ions was observed from the film annealed in $O_2$ ambient. Broad PL spectra associated with $Eu^{2+}$ ions, with a maximum intensity at 600 nm and a FWHM of 110 nm, were observed from the thin film annealed at $1000^{\circ}C$ in $N_2$ ambient.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권7호
• /
• pp.525-529
• /
• 1999

The influence of ambient gases on field emission performance of Mo-field emitter array(FEA) in the frit-sealing step of field emission display(FED) packaging process was investigated. Mo-tip FEA was mounted on the glass substrate having a surrounded frit(Ferro FX11-137) and fired at $415^{\circ}C$ in the ambient gases of air, $N_2$ and Ar. The Ar gas was proved to be most proper ambient among the used gases through evaluating the turn-on voltage and field emission current of the fired Mo-tip FEA devices. It was confirmed that the Mo surface fired in Ar ambient was less oxidized when compared with another ones annealed in air and Ar ambient by the AFM, XPS, AES and SIMS analysis. Finally, the 3.5 inch-sized Mo-tip FED, which was packaged using frit-sealing process in the Ar ambient, was proposed.

• 대한기계학회논문집B
• /
• 제25권5호
• /
• pp.627-633
• /
• 2001

Characteristics of a diesel spray impingement with the variation of ambient temperature, wall temperature and ambient pressure were investigated through shadowgraphy method by using high speed camera. The radial penetration of spray was increased with ambient temperature and wall temperature. It is resulted from the decrease of ambient gas density caused by the increase of temperature. The height of spray was also increased with ambient temperature and wall temperature, because the height of stagnate region is noticeably increased, although height of wall jet vortex is decreased. At the same ambient pressure, the area ratio of impinging spray of room temperature environment to high temperature environment was increased, as the temperature difference between room temperature and high temperature increases. And the increment of area ratio was higher at low ambient pressure than high ambient pressure.

• 한국진공학회지
• /
• 제16권2호
• /
• pp.116-121
• /
• 2007

Ti-50 at. % Ni 합금 타깃으로 PLD(pulsed laser deposition)방법을 사용하여 TiNi 형상기억합금 박막을 제작하였다. Ar분위기(200 mTorr)와 고진공분위기($5{\times}10^{-6}\;Torr$)에서 제작한 TiNi 박막의 조성 및 결정성의 변화를 조사했으며, 박막의 조성은 에너지 분산 엑스선 분광 분석(EDXS)을 이용하여 조사하였고, 박막의 결정성은 엑스선 회절장치(XRD)를 이용하여 조사하였다. 박막의 조성은 기판과 타깃의 거리에 의존되었지만, 기판의 온도와는 무관함을 알 수 있었으며, Ar 분위기에서 플룸 안쪽에 기판이 위치하였을 때 조성 제어가 용이함을 알 수 있었다. 또한, Ar 가스 분위기에서 증착 된 TiNi 박막은 고진공분위기에서 증착된 박막보다 더 낮은 온도(약 $400^{\circ}C$)에서 in situ로 결정화됨을 알 수 있었다. 이들 결과는, PLD방법으로 TiNi 형상기억합금 박막을 제작할 때 분위기 가스의 압력이 결정화 온도를 낮추어 주는 중요한 역할을 할 수 있음을 시사한다.

• The Korean Journal of Ecology
• /
• 제22권2호
• /
• pp.79-83
• /
• 1999

Phytotoxic effects of ozone and ethylenediurea (EDU) on soybean (Glycine max) and spinach (Spinacia oleracea) were observed by using open-top field chamber system (OTC). Gas exchange rates (photosynthesis. stomatal conductance and transpiration rates) of soybean plants were decreased by 20% to 30% by ambient ozone and resulted in 30% reduction of seed yields. In OTC. ambient ozone and 0.12 $\mu$l/l $O_3$ decreased gas exchange rates of spinach by 25% to 40% and by 50%. respectively. The protective effect of EDU against ozone induced injury was obtained at 100 mg/l on soybean. and at 250 mg/l on spinach, respectively. The excessive application of EDU. however. inhibited photosynthesis. transpiration. and stomatal conductance without any specific visible damage.