• 대한기계학회논문집B
• /
• 제30권7호
• /
• pp.682-691
• /
• 2006

This study was conducted to assess the effect of mixed fuel composition and mass fraction on spray inner structure in evaporating transient spray under the various ambient conditions. Spray structure and spatial distribution of liquid phase concentration are investigated using a thin laser sheet illumination technique on the multi-component mixed fuels. A pulsed Ar+ laser was used as a light source. The experiments were conducted in a constant volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. Used fuel contain $i-octane(C_8H_{18}),\;n-dodecane(C_{12}H_{26})$ and $n-hexadecane(C_{16}H_{34})$ that are selected as low-, middle- and high-boiling point fuel, respectively. Experimental conditions are 25Mpa, 42MPa, 72MPa and 112MPa in injection pressure, $5kg/m^3,\;15kg/m^3\;and\;20kg/m^3$ in ambient gas density, 400K, 500K, 600K and 700K in ambient gas temperature, 300K and 368K in fuel temperature, and different fuel mass fraction. Experimental results indicate that the more high-boiling point component, the longer the liquid phase it were closely related to fuel physical properties, but injection pressure had no effect on. And there was a high correlation between the liquid phase length and boiling temperature at 75% distillation point.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권5호
• /
• pp.707-716
• /
• 2008

The objective of this study was to analyze the effect of mixed fuel composition and mass fraction on spray inner structure in evaporating transient spray under the variant ambient conditions. Spray structure and spatial distribution of liquid phase concentration were investigated using a thin laser sheet illumination technique on the three component mixed fuels. A pulsed Nd:YAG laser was used as a light source. The experiments were conducted in a constant volume vessel with optical access. Fuel was injected into the vessel with electronically controlled common rail injector. Used fuel contains i-octane($C_8H_{18}$), n-dodecane($C_{12}H_{26}$) and n-hexadecane($C_{16}H_{34}$) that were selected as low-, middle- and high-boiling point fuel, respectively. Experimental conditions are 42 MPa, 72 MPa and 112 MPa in injection pressure, $5\;kg/m^3$, $15kg/m^3$ and $30kg/m^3$ in ambient gas density, 300 K, 500 K, 600 K and 700 K in ambient gas temperature, 300 K and 368 K in fuel temperature and different fuel mass fraction. Experimental results indicated that the multi-component fuels made two phase region mixed vapor and liquid so that it would are helpful to improve combustion, for the fuels of high boiling point component could accelerate evaporation very much according as low boiling point fuel was added to high boiling point fuel.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.207.1-207.1
• /
• 2014

High-mobility and two dimensional conduction at the interface between two band insulators, LaAlO3 (LAO) and SrTiO3 (STO), have attracted considerable research interest for both applications and fundamental understanding. Several groups have reported the photoconductivity of LAO/STO, which give us lots of potential development of optoelectronic applications using the oxide interface. Recently, a giant photo response of Pd nano particles/LAO/STO is observed in UV illumination compared with LAO/STO sample. These phenomena have been suggested that the correlation between the interface and the surface states significantly affect local charge modification and resulting electrical transport. Water and gas adsorption/desorption can alter the band alignment and surface workfunction. Therefore, characterizing and manipulating the electric charges in these materials (electrons and ions) are crucial for investigating the physics of metal oxide. Proposed mechanism do not well explain the experimental data in various ambient and there has been no quantitative work to confirm these mechanism. Here, we have investigated UV photo response in various ambient by performing transport and Kelvin probe force microscopy measurements simultaneously. We found that Pd nano particles on LAO can form Schottky contact, it cause interface carrier density and characteristics of persistence photo conductance depending on gas environment. Our studies will help to improve our understanding on the intriguing physical properties providing an important role in many enhanced light sensing and gas sensing applications as a catalytic material in different kinds of metal oxide systems.

• 센서학회지
• /
• 제7권1호
• /
• pp.51-60
• /
• 1998

초전형 적외선센서를 제조하기 위하여 La가 첨가된 $PbTiO_{3}$(PLT)박편을 소결온도, La첨가량 및 소결시의 분위기분말의 양과 같은 제조조건을 달리하면서 제조하여 이에 따른 시편의 구조적 특성을 X-선 회절기, 전자현미경 및 상대밀도의 측정을 통하여, 유전특성을 유전상수와 큐리온도 등의 측정을 통하여 조사하였다. La 첨가랑이 증가함에 따라 정방성비 c/a는 감소하였으며, 상대밀도 및 입자의 크기는 증가하였다. 이는 La 첨가량이 증가함에 따라 전하중성을 유지하기 위한 Pb공공의 증가에 기인하는 것으로 판단된다. 소결시 분위기분말의 증가는 La 첨가에 따른 효과에 비해 미미하지만 정방성비를 미세하게나마 증가시켜 PbO의 휘발을 감소시키는 것으로 나타났다. La 첨가량에 따른 정방성비의 감소로 상온에서의 유전상수는 증가하였으며 큐리온도는 감소하였다.

• 한국항해항만학회지
• /
• 제32권8호
• /
• pp.637-643
• /
• 2008

해양방류시스템을 계획할 때 우선목표는 방류수의 초기희석을 극대화하는 것이다. 이를 효과적으로 달성하기 위해서는 방류수와 주변수의 혼합현상, 특히 초기혼합영역인 근역에 대한 특성분석이 선행되어야 한다. 최근까지 최적의 방류시스템(outfall system) 구현을 위하여 근역(NFR)에서의 온배수 방류에 관한 많은 연구가 이루어지고 있지만 온배수(heat discharge)와 염배수(brine discharge)를 동시에 방류할 경우를 고려한 성과물을 찾기는 어려운 실정이다. 이에 본 연구에서는 온수와 염수를 동시에 고려한 방류시스템의 최적설계를 위한 기초자료를 제공하기 위하여 방류수의 거동양상 특히, 근역에서의 혼합성을 분석하였다. 수치실험은 표면방류, 단일확산관 방류, 다공확산관 방류를 해당 해역의 법적 수질기준에 부합하는지 여부를 주로 평가하였다. 그 결과 표면방류와 단일확산관 방류는 방류형식이 부적절하였고, 다공확산관의 경우도 기하학적인 형상에 따라 결과가 조금 상이하였다.

• 한국동물위생학회지
• /
• 제44권4호
• /
• pp.217-225
• /
• 2021

We investigated the effect of temperature and stock density on the collection efficiency of oral fluid in the pig farm in Korea. Three pig farms with similar breeding environmental conditions were selected and four pens of each farm (total 12 pens) were tested for the collection efficiency of oral fluid from pigs. Collection rate was considered as significant when oral fluid was collected from 70% of pigs within a pen. In the case of growing pigs, when internal temperature of pig barn increased by one designated degree (5℃), the oral fluid collection rate significantly decreased by 24.7% (P<0.05). The collection rate of oral fluid also decreased by 7.1% (P<0.05) as the density rate increase by one designated degree (12.5%). It was estimated that the collection efficiency of oral fluid decreased when the internal temperature of pig barn was 30℃ or higher, or barn density is higher 25% or high. On the other hand, in the case of stall-housing sows, unlike growing pigs, there was no significant differences according to the temperature, so oral fluid collection was considered to be efficient even in hot season.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.122-122
• /
• 2008

Recently, Metal/Alumina/Silicon-Nitride/Silicon-Oxide/Silicon (MANOS) structures are one of the most attractive candidates to realize vertical scaling of high-density NAND flash memory [1]. However, as ANO layers are miniaturized, negative and positive bias temperature instability (NBTI/PBTI), such as the flat band voltage shift, ${\Delta}V_{FB}$, the interfacial trap density increase, ${\Delta}D_{it}$, the gate leakage current, ${\Delta}I_G$. and the retention characteristics, in MONOS capacitors, becomes an important issue in terms of reliability. It is well known that tunnel oxide degradation is a result of the oxide and interfacial traps generation during FN (Fowler-Nordheim) stress [2]. Because the bias temperature stress causes an increase of both interfacial-traps and fixed oxide charge could be a factor, witch can degrade device reliability during the program and erase operation. However, few studies on NBTI/PBTI have been conducted on improving the reliability of MONOS devices. In this work, we investigate the effect of post-annealing gas on bias temperature instability (BTI), such as the flat band voltage shift, ${\Delta}V_{FB}$, the interfacial trap density shift, ${\Delta}I_G$ retention characteristics, and the gate leakage current characteristics of MANOS capacitors. MANOS samples annealed at $950^{\circ}C$ for 30 s by a rapid thermal process were treated via additional annealing in a furnace, using annealing gases $N_2$ and $N_2-H_2$ (2 % hydrogen and 98 % nitrogen mixture gases) at $450^{\circ}C$ for 30 min. MANOS samples annealed in $N_2-H_2$ ambient had the lowest flat band voltage shift, ${\Delta}V_{FB}$ = 1.09/0.63 V at the program/erase state, and the good retention characteristics, 123/84 mV/decade at the program/erase state more than the sample annealed at $N_2$ ambient.

• 비파괴검사학회지
• /
• 제31권1호
• /
• pp.24-31
• /
• 2011

콘크리트 벽체 구조물에 매입된 철근의 정량적인 부식률을 측정하기 위하여 자연전위 측정법과 적외선 열화상법을 이용하였다. 벽체 실험체는 부식률(0, 1, 3, 5, 7%)과 피복 두께(30 mm, 40 mm), 그리고 철근 배근 간격에 변수를 주어 콘크리트 표면에서 저항 및 전류를 측정하고 온도를 측정하였으며, 콘크리트 표면 상태에서 얻은 결과를 분석하여 다음과 같은 결론을 얻었다. 전류밀도 분포는 부식률이 증가할수록 그값이 증가하였으며 피복 두께가 클수록 분포도가 넓게 나타났다. 적외선 촬영으로 얻어진 열화상 정보는 서로 다른 부식률과 피복 두께에서는 현저한 차이를 보였으며 주변 온도 및 철근 배근 간격에 대해서는 그 영향이 미비하게 나타났다. 제시된 부식 모델을 통해서 콘크리트 표면의 전류나 온도를 측정하여 내부에 매입되어 있는 철근의 부식률을 정량적으로 측정할 수 있는 것으로 나타났다.

• 천문학회보
• /
• 제35권2호
• /
• pp.49.1-49.1
• /
• 2010

The study of pores, small penumbraless sunspots, can give us a chance to understand how strong magnetic fields interact with convective motions in the photosphere. For a better understanding of this interaction, we investigate the temporal variation of several tiny pores smaller than 2". These pores were observed by the Solar Optical Telescope (SOT) onboard Hinode on 2006 December 29. We have analyzed the high resolution spectropolarimetric (SP) data and the G-band filtergrams taken during the observation. Magnetic flux density and Doppler velocities of the pores are estimated by applying the center of gravity (COG) method to the SP data. The horizontal motions in and around the pores are tracked by adopting the Nonlinear Affine Velocity Estimator (NAVE) method to the G-band filter images. As results, we found the followings. (1) Darkness of pores is positively correlated with magnetic flux density. (2) Downflows always exist inside and around the pores. (3) The speed of downflows inside the pores is negatively correlated with their darkness. (4) The pores are surrounded by strong downflows. (5) Brightness changes of the pores are correlated with the divergence of mass flow (correlation coefficient > 0.9). (6) The pores in the growing phase are associated with the converging flow pattern and the pores in the decay phase with the diverging flow pattern. Our results support the idea that a pore grows as magnetic flux density increases due to the convergence of ambient mass flow and it decays with the decrease of the flux density due to the diverging mass flow.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.869-878
• /
• 2001

Alumina $(Al_2O_3)$ green bodies were fabricated by gel-casting using three kinds of alumina with different particle size (mean particle size: 4.6 $\mu\textrm{m}$, 0.32 $\mu\textrm{m}$, 10nm). The effects of particle size on gel-casting process and green microstructure were investigated. The optimum dispersion conditions using ammonium salt (D-3019) as dispersant were 0.2 wt% (4.63 $\mu\textrm{m}$), 0.5 wt% (0.32 $\mu\textrm{m}$), and 5.0 wt% (10 nm), in high solid loading. The optimum solid loading of each starting material for gel-casting was obtained as 59 vol% (4.63 $\mu\textrm{m}$), 57 vol% (0.32 $\mu\textrm{m}$), 15 vol% (10 nm), depending on particle size, indicating that nano-size particle (10 nm) represent lower solid loading as high specific surface area than those of other two starting materials. The drying at ambient conditions (humidity; $\thickapprox$90%) was performed more than 48hrs to enable ejection of the part from the mold and then at $120^{\circ}C$ for 2hrs in an air oven, showing no crack and flaw in the dried green bodies. The pore size and distribution of the gelcast green bodies showed the significant decrease with decreasing particle size. Green microstructure was dependent on the pore size and distribution due to the particle size, and on the deairing step. The green density maximum obtained was 58.9% (4.63 $\mu\textrm{m}$), 60% (0.32 $\mu\textrm{m}$), 47% (10 nm) theoretical density (TD), and the deairing step applied before gel-casting did not affect green density.