• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.164-168
• /
• 2011

This study of PV modules in the external environment, learn about the mechanical strength characteristics, the module will investigate the aluminum frame. Positive support in the module by wind loads if uniformly distributed load acting on the front glass of the module size and elongation(${\omega}$), and accordingly, depending on the bend is sealed inside the solar cell, micro-cracks that will occur. At this point the most damage-prone parts in a module, this module is part of the center of a strong wind load is applied by the destruction of the environment does not occur in the module frame to secure the reliability and to evaluate changes in the structure.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 금형가공 심포지엄
• /
• pp.285-291
• /
• 2002

The shearing process for the sheet metal is normally used in the precision elements such as a frame of TFT-LCD or lead frame of If chips. In these precision elements, the burr formation prevents the system assembly and needs the additional burr removing process. In this paper, we developed the small size NC punching system which has an aligning kinematics between the rectangular shaped punch and die. The punch is driven by an ai cylinder and the sheet metal is moving on the X-Y table system which is driven by two stewing motors. The microprocessor control the whole system and communicate with the monitoring PC by RS232C serial communication protocol. The graphic user interface program in PC monitors nil control the punching system. The cross shaped joint hinge supports the punching die and positioned by two differential screws, whose are installed in perpendicular directions. The aligning between the punch and die is performed using the sheets of half thickness(0.1mm Brass) of the real process for the frame of the TFT-LCD. Using half thickness Brass, the burr formation is magnified and we can decide the aligning direction more easily then using the real thickness(0.2mm) Aluminum. In this paper, the aligning results are measured manually using the SEM photographs and we hope to make the automated aligning procedures using some kinds of image processing techniques.

• 대한기계학회논문집 C: 기술과 교육
• /
• 제5권2호
• /
• pp.89-95
• /
• 2017

제품을 개발하는데 있어서 경량화와 원가절감이라는 두가지 요소는 가장 중요한 화두이다. 특히 대형 LCD 로봇은 최대 $3{\times}3m$ 이상의 글라스를 7m 높이까지 상하, 전후로의 직선운동과 선회축을 중심으로한 회전운동을 하면서 작업공정간 이송을 가능케 하는 대형 구조물이다. 따라서 지나치게 무거울 경우에는 클린룸내 설치에 문제가 있을 수 있고 반송물의 정확한 이송을 위하여는 고강성이 요구되며 대량 생산을 위한 연속작업을 충분히 감당할 수 있는 내구강도를 확보하여야 한다. 따라서 경량화, 고강성, 고강도 제품에 대한 요구는 갈수록 증가하고 있다. 현재 개발되고 있는 11 세대 대형 LCD 승강프레임은 이러한 요구조건을 충족하기 위하여 최적설계 기법을 적용하여 기존 제품 대비 경량화와 고강성 요구조건을 만족하였으며 용접부에 대한 상세 수명평가로 내구강도에 대한 신뢰성을 확보하였다.

• 한국염색가공학회지
• /
• 제34권4호
• /
• pp.241-249
• /
• 2022

As for military backpacks in Korea, utility backpack products equipped with various functions along with comfort and convenience are being developed. As a result, the volume and weight of the backpack increase, and many lightweight studies of the materials forming the backpack are being conducted. This study is a basic study on frame lightweight using fiber-reinforced composites to deal with aluminum, a back frame that maintains the shape of a backpack and provides stability when worn by combatants. As is known, only fiber-reinforced composites have sufficient light weight and mechanical properties, but the mechanical properties were reviewed by drilling holes to maximize the light weight. Tensile strength and flexural strength were measured by drilling 6mm, 12mm, 18mm, and 24mm holes, and the tensile strength and flexural strength were measured when 1, 3, 5, and 7 holes of 12mm were increased. As a result, even when the number of holes was increased, tensile strength did not change significantly, and the flexural strength showed to be higher in the case of 3 holes and 5 holes than in the case of 1 hole.

• 한국전기전자재료학회논문지
• /
• 제36권3호
• /
• pp.292-297
• /
• 2023

Triboelectric devices are attracting attention from researchers as self-powered electronic systems that can instantly convert mechanical input into electrical energy output. To improve triboelectric energy harvesting performance, increasing the number of contacts as well as the contact area has been carried out by numerous researchers. In this study, we design a shaker-type energy harvester which is called as maracas triboelectric generator (M-TEG), inspired by the structure of maracas, one of the musical percussion instruments. A tripod frame is inserted to the inside of a cylindrical case, which is a device with the electrodes of aluminum and copper. Then, the triboelectric energy harvesting characteristics between polypropylene (PP) balls and the electrodes are measured. The M-TEG with the frame generates the energy harvesting signals up to ~100 V and ~2.5 ㎂ due to larger contact area and numbers, which enhances the voltage and current output by 250% and 610% compared to that without the frame, respectively. This study presents the feasibility of self-powered sensors and toys using improved triboelectric energy performance with a low-cost and simple manufacturing process in the interesting structure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3021-3026
• /
• 2007

In this paper, experimental data on flow pattern transition of inclination angles from 0-90 are presented. A test section is constructed 2 mm long and I.D 1inch using transparent material. The test section is supported by aluminum frame that can be placed with any arbitrary inclined angles. The air-water two-phase flow is observed at room temperature and atmospheric condition using both high speed camera and void impedance meter. The signal is sampled with sampling rate 1kHz and is analyzed under fully-developed condition. Based on experimental data, flow pattern maps are made for various inclination angles. As increasing the inclination angels from 0 to 90, the flow pattern transitions on the plane jg-jf are changed, such as stratified flow to plug flow or slug flow or plug flow to bubbly flow. The transition lines between pattern regimes are moved or sometimes disappeared due to its inclined angle.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.151-158
• /
• 2005

An important component of a cooling tower is an axial fan, and there happens distortion in its shape which brings significant loss of efficiency. In this paper, a surface profile measuring system for large size axial fan of cooling towers is developed. A laser sensor is used as a measuring device and aluminum profiles and stepping motors are engaged into the system as frame structure and driving devices respectively. The measuring data are compared to the design data to compute the distortion of the axial fans. Two types of errors, axial and twist errors, are used to represent the precision of axial fan distortion. Genetic algorithm is used to solve the optimization problem during computing the precision. Results are displayed three dimensionally in a solid-modeler as well as 2-D drawings to help users find it with ease.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.409-412
• /
• 2004

In this paper, an integrated automation system of pattern design and $CO_2$ laser cutting for diving suits is presented. Pattern design includes grading which creates a full-size range from a base pattern. Tool path for laser cutting from the patterns is generated in G-code format. $CO_2$ Laser cutting machine is developed to help cut the patterns with accuracy and speed. Aluminum profiles, ball screws, and stepping motors are engaged into the machine as frame structure, transfer unit, and driving devices respectively. The developed system is tested in dry suit cutting, convincing it can be readily introduced in driving suits manufacturing with respect to cost and efficiency.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.185-188
• /
• 2004

Regarding some of the components of the Korean Tilting Train eXpress(TTX), the lightweight-vehicle development was mainly focused to this study, and so as using the materials, the existing material, steel or aluminum carbody was changed to the composite carbody with both design and manufacturing methods. Therefore the evaluation of the performance of joint strength between composite and metallic boundary area, especially the under frame and the carbody was required, and the compressive and the bending tests were conducted as the sub-scale specimen. In this evaluation, there was involved the sufficient strengths at the joint area between the underframe and the carbody, and is resulted as the increment of the safety factor through the observation of failure conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.925-928
• /
• 2003

In this paper, a precision measuring machine for large sized axial fans of cooling towers are developed. A laser sensor is used as a measuring device and aluminum profiles and stepping motors are engaged into the system as frame structure and driving devices respectively. 3-dimensional measuring data are compared to the design data to compute the distortion of the axial fans. Two distortions such as the axis of the fan and the airfoils along the axis are introduced to define the shape precision of axial fans. Genetic algorithm is used to solve the optimization problem during computing the distortion. Results of distortion are displayed 3 dimensionally in a solid-modeler as well as 2-D drawings to help users find it with case.