• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.2
• /
• pp.61-65
• /
• 2024

HVPE (Hydride vapor phase epitaxy) is a method of manufacturing thin films or single crystals using gaseous raw materials. This is a method that applies the principles of chemical vapor deposition to grow a single crystal of a material with low meltability or high melting point, and is one of the methods that can obtain a gallium nitride (GaN) single crystal. Recently, much research has been conducted to grow aluminum nitride (AlN) single crystals using this method, but good results have not yet been obtained. In this study, we attempted to grow AlN single crystals using the HVPE method. Nitrogen was used as a carrier gas in the growth process, and the growth results according to changes in the amount of nitrogen (N₂) were examined. Changes in growth crystals as the amount of nitrogen increased were confirmed. The shape of the grown AlN single crystal was observed using an optical microscope, and the rocking curve was measured using double crystal X-ray diffractometry (DCXRD) to confirm the creation of the AlN crystal. The crystallinity of single crystals was also investigated.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.127-134
• /
• 2015

Aluminum nitride (AlN) single crystals have attracted much attention for a next-generation semiconductor application because of wide bandgap (6.2 eV), high thermal conductivity ($285W/m{\cdot}K$), high electrical resistivity (${\geq}10^{14}{\Omega}{\cdot}cm$), and high mechanical strength. The bulk AlN single crystals or thin film templates have been mainly grown by PVT (sublimation) method, flux method, solution growth method, and hydride vapor phase epitaxy (HVPE) method. Since AlN suffers difficulty in commercialization due to the defects that occur during single crystal growth, crystalline quality improvement via defects analyses is necessary. Etch pit density (EPD) analysis showed that the growth misorientations and the defects in the AlN surface exist. Transmission electron microscopy (TEM) and electron back-scattered diffraction (EBSD) analyses were employed to investigate the overall crystalline quality and various kinds of defects. TEM studies show that the morphology of the AlN is clearly influenced by stacking fault, dislocation, second phase, etc. In addition EBSD analysis also showed that the zinc blende polymorph of AlN exists as a growth defects resulting in dislocation initiator.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.5
• /
• pp.168-173
• /
• 2020

To analyze and describe the behavior and mechanisms occurring in the thermal oxidation process of AlN, bulk AlN single crystals were thermally treated with different temperatures. As a result, it was confirmed that full-scale oxidation of bulk AlN and growth of Al-oxide occurred from the temperature of 800℃, which confirmed that the weight% of O elements tended to increase while the N elements decreased with increasing the temperature. In the case of thermal treatment at 900℃, the grown Al-oxides were merged with neighboring Al-oxides and began to form α-Al₂O₃ poly-crystals. During thermal treatment at the temperature of 1000℃, hexagonal pyramidal shaped poly-crystalline α-Al₂O₃ was clearly observed. Through the X-ray diffraction pattern analysis, the changes of surface crystal structure according to the temperature of bulk AlN were investigated in detail.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.111-111
• /
• 2009

In this work, we discuss simulation of surface acoustic wave device using Comsol Multiphysics. The structure SAW device based on piezoelectric thin film aluminum-nitride (AlN) on silicon was simulated. Some parameters of SAW device such as surface velocity, displacement of piezoelectric thin film were evaluated by software. Many modes and shapes of wave are also discussed in this paper. For evaluation physical parameters of AlN piezoelectric layer, the SAW resonator was modeled and simulation results were also compared with experiment results. we simulated arid evaluated the surface Rayleigh wave of AlN thin film on silicon substrate. Results simulation and experiment showed the surface velocity of AlN thin film was about 5200 m/s and shape of surface wave was also displayed. This paper has also proposed as method to study SAW characteristic of piezoelectric thin film and found out measurement values accurately of film such as stiffness matrix, piezoelectric matrix. These values are very important in calculation and design SAW device or MEMS device based on AlN piezoelectric layer.

• Journal of the Korean Ceramic Society
• /
• v.24 no.5
• /
• pp.453-460
• /
• 1987

β'-sialon(Z=2.7) specimens with <30%wt. graphite as a reducing agent were decomposed at 1350°up to 1,450℃ under the atmosphere of 90% N2-10%H2. The decomposition of β'-sialon was calculated from the change in Z-value, and the formation of new minerals was identified from X-ray diffraction patterns. The decomposition reactions of sialon were considered to yield a stable sialon close to β-silicon nitride and some aluminum compounds according to the following equations; β'-sialon(s)＋C(s)＋N2(g)→β2-sialon(metastable)＋β3-sialon(stalbe phase) β2-sialon(s)＋C(s)＋N2(g)→β3-sialon(s)＋AlN(s)＋α-Al2O3(s)＋15R(s)＋SiO(g)＋Al2O(g)＋CO(g) Z-value; β2( 3.5)>β'( 2.7)>β3( 0.5) The decomposition rate of sialon was controlled by two mechanisms ; One was characterized by the interface area of contact, corresponding to an apparent activation energy of 50.5Kcal/mol in the initial stage, and the other by the diffusion, corresponding to that of 104.3Kcal/mol in the final stage of the decomposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.252-252
• /
• 2009

In this work, the nanocrystalline ZnO/polycrystalline (poly) aluminum nitride (AlN)/Si structure was fabricated for humidity sensor applications based on surface acoustic wave (SAW). In this structure, the ZnO film was used as sensing material layer. These ZnO and AlN(0002) were deposited by so-gel process and a pulse reactive magnetron sputtering, respectively. These experimental results showed that the obtained SAW velocity on AlN film was about 5128 m/s at $h/\lambda$=0.0125 (h and $\lambda$ is thickness and wavelength, respectively). For ZnO sensing layers coated on AlN, films have hexagonal wurtzite structure and nanometer particle size. The crystalline size of ZnO films annealed at 400, 500, and 600 $^{\circ}C$ is 10.2, 29.1, and 38 nm, respectively. Surface of the film exhibits spongy which can adsorb steam in the air. The best quality of the ZnO film was obtained with annealing temperature at 500 $^{\circ}Cis$. The change in frequency response (127.9~127.85 MHz) of the SAW humidity sensor based on ZnO/AlN structure was measured along the change in humidity (41~69%). The structural properties of thin films wereinvestigated by XRD and SEM.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.2
• /
• pp.250-254
• /
• 2003

A film bulk acoustic resonator (FBAR) device for 2 GHz radio frequency (RF) bandpass filter application is presented. This FBAR device consists of an aluminum nitride (AlN) film sandwiched between top(Al) and bottom(Au) electrodes and an acoustic multilayer reflector of a silicon dioxide/tungsten (SiO2/W). The A/N film deposited using a RF sputtering was observed to have small columnar grains with a strongly preferred orientation towards c axis. In addition to a high quality factor (4300), a large return loss of 37.19 dB was obtained.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.915-920
• /
• 2007

AIN-based film bulk acoustic resonator (FBAR) devices which adopt a membrane-type configuration such as Mo/AIN/bottom-metal/Si are fabricated by employing a novel process. The proposed resonator structure does not require any supporting layer above the substrate, which leads to the reduction in energy loss of the resonators. For all the FBAR devices, the frequency response characteristics are measured and the device parameters, such as return loss and input impedance, are extracted from the frequency responses, and analyzed in terms of the various metals such as Al. Cu, Mo, W used in the bottom-electrode. The mass-loading effect caused by the used bottom-electrode metals is found to be the main reason for the difference revealed in the measured characteristics of the fabricated FBAH devices. The results obtained in this study also show that the degree of match in lattice constant and thermal expansion coefficient hetween piezoelectric layers and electrode metals is crucial to determine the device performance of FEAR.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.1
• /
• pp.29-33
• /
• 2013

We have fabricated transparent polymer composite films with high thermal emissivity, which can be used for heat dissipation of transparent electronics. PMMA (poly(methyl methacrylate)) solution with high transparency and thermal emissivity is mixed with various fillers (carbon nanotubes (CNTs), aluminum nitride (AlN), or silicon carbide (SiC)) with high thermal conductivity. We have achieved the thermal emissivity as high as 0.94 by the addition of CNTs. Compared with the PMMA film on glass, however, the addition of AlN or SiC is shown to rather decrease the thermal emissivity. It is also observed that the thickness of the PMMA film does not affect its thermal emissivity. To avoid any degradation of the thermal conductivity, therefore, the PMMA film thickness is desirable to be $1{\mu}m$. There also exists a tradeoff between the optical transmittance and thermal conductivity on the selection of the amount of fillers.

• Journal of Magnetics
• /
• v.15 no.3
• /
• pp.123-127
• /
• 2010

The use of a cooling fan in an induction cooker raises a reliability issue due to the attraction of dust causing a malfunction of the cooling fan and also increases the noise level and power consumption of the device. The purpose of this study is to attempt to solve these problems by molding the Cu coil of an induction cooker with polymer composites that have a low electrical conductivity but a high thermal conductivity. Among the several polymer composites tested in this study, an aluminum nitride-based composite showed the best performance. The results show that the new induction cooker with the molded composite can operate for an extended period of time without the use of a cooling fan. A further advantage of this new type of induction cooker is that the temperature of the substance in the cooking pot increases more rapidly, indicating an increased efficiency of the induction cooker.