• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.11 s.176
• /
• pp.45-50
• /
• 2005

In this study, the casting/forging process was applied in manufacturing a low control arm, in order to prove that application of casting/forging process to Al6061 is likely to get the effect of light weight compared with existing steel products and to reduce the cost of materials. Firstly, In order to set up the optimum casting condition of the forging material, Al6061, casting experiments were carried out by controlling pouring temperature of the aluminum for casting, mold temperature, and pouring time. $700^{\circ}C$ pouring temperature, $300^{\circ}C$ mold temperature and 10-second pouring time were taken into account as the optimum casting conditions. With respect to a hot forging test, it is practiced on the basis of a temperature of materials, strain rate, and reduction rate so as to observe each microstructure and examine strain-stress curve simultaneously; examine tensile test and hardness test; eventually set up the optimum hot forging condition. A hot forging test, tensile test, hardness experiment, and microstructure observation were carried out on condition of $70\%$ reduction rate, $500^{\circ}C$ temperature of materials, and 1 strain rate. As a result of those experiments, 330MPa tensile strength, $16.4\%$ elongation, and 122.8Hv hardness were recorded. In oder to get a sound preform which has no unfitting cavity and less flash, two preforms were proposed on the basis of volume rate of the final product; the optimum volume rate of preform for the low control arm was $115\%$. In conclusion, it is confirmed that using the forging material rather than casting materials in casting/forging process is likely to get more superior mechanical properties. Compared with Al6061, performed by means of general forging, moreover, cast/forged Al6061 can not only stimulate productivity by reducing production processes, but cut down the cost of materials by reusing forging scraps.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.552-558
• /
• 2015

The mechanical properties and microstructures of Aluminum 6056 alloys were investigated for their use in the fabrication of a piton block. The EN-AW6056 alloys exhibited a tensile strength of 375 MPa for a solution treatment temperature of $550^{\circ}C$ for 2 h followed by an aging treatment at $190^{\circ}C$ for 4 h. The microstructures of the heat treated specimen showed that the $Mg_2Si$ phase with a size of 3~5 um was dispersed throughout the aluminum matrix when the heat treatment was done. Moreover, in order to identify the forgeability of the specimen, upsetting tests were done. For up to 80 % of the upsetting ratio, the specimen maintained its original shape, and at above 80 % of the upsetting ratio, the specimen underwent crack development. The specimen was successfully forged without any defects with the examined material conditions. The material conditions together with the forging conditions are discussed in terms of the microstructures and mechanical properties.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.9
• /
• pp.5789-5794
• /
• 2015

Recently, thin and light-weight production technologies are needed in IT industry in accordance with increase of the smart phones and mobile PC products. In order to make light and high rigidity products, engineering plastic and aluminum materials are frequently used in products appearance and frame hat support structure. Especially aluminum extrusion and CNC Brick processes are widely used for high strength and high rigidity technology. But extrusion method has constraints to apply exterior design and CNC Brick process has relatively high production cost and low speed of manufacturing. In this research, a new process method is introduced in order to reduce material cost and to improve manufacturing speed dramatically. Plate forging process means basically that thickening of local wall area thickness after deform exterior shape by deep drawing and bending process. Therefore, it is possible to minimize the waste of material and the manufacturing time. In this study the process of plate forging is designed using finite element program AFDEX-2D and the thickness and the width of initial deformed blank. And it is verified as a sample which is a part of laptop developed through the proposed plate forging method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.2
• /
• pp.46-53
• /
• 2000

Hot forging of aluminum alloy has the bad machinability due to continuous chip formation caused from the ductility The bad machinability requires a labor and a high cost to produce final products after hot forging. In industrial field, T4 heat treatment is performed to improve the machinability, and the annealing and the cold sizing are followed. In this study, a series of heat treatments are introduced during hot forging operation without T4 heat treatment after forming so that it improves the machinability with reduction of the number of operations and machining cost. Instead of T4 heat treatment, water cooling and air cooling are tried and compared to find out an optimum cooling condition

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.22 no.1
• /
• pp.173-177
• /
• 2013

The purpose of this paper is to investigate the influences on mechanical properties of two-stroke cycle motor pistons manufactured by casting, conventional forging and powder forging, through the comparison of characteristics, merits and disadvantages of each forming technology. For each forming technology, the optimal process parameters were determined through the experiments for several conditions, and microstructure, hardness, tensile strength and elongation of pistons are compared and analyzed. In conventional forging process, material temperature was $460^{\circ}C$ and the die temperature was $210^{\circ}C$ for the Al 4032. The optimal condition was found as solution treatment under $520^{\circ}C$ for 5 hours, quenching with $23^{\circ}C$ water, and aging under $190^{\circ}C$ for 5 hours. In powder forging process, the proper composition of material was determined and optimal sintering conditions were examined. From the experiment, 1.5% of Si contents on the total weight, $580^{\circ}C$ of sintering temperature, and 25 minutes of sintering time were determined as the optimal process condition. For the optimal condition, the pistons had 76.4~78.3 [HRB] of hardness, and 500 [MPa] of tensile strength after T6 heat treatment.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.131-134
• /
• 2007

A semi-solid forming technology has a lot of advantages compared to the die casting, squeeze casting and hot/cold forging, so semi-solid forming has been studied actively. Semi-solid forming has two methods. One is thixoforming with reheating of prepared billet, the other is rheoforming with cooled melt until semi-solid state. Thixoforging technology can produce non-dendritic alloys for semi-solid forming complex shaped parts in metal alloys. In this study, the thixoforging was experimented with made rheology materials by the spiral stirrer equipment. Rheology materials for forging were made by A356 casting aluminum alloy and A6061 wrought aluminum alloy. After experiment, forged samples were measured microstructure and were heat treated for high mechanical properties.

• Transactions of Materials Processing
• /
• v.5 no.3
• /
• pp.239-255
• /
• 1996

A new forming technology has been developed to fabricate near-net shape products using light metal. A semi-solid forming technology has some advantages compared with the conventional forming processes such as die casting squeeze casting and hot/cold forging. In this study the numerical analysis of semi-solid filling for a straight die shape and orifice die shape in gate pattern is studied on semi-solid materials(SSM) of solid fraction fs =30% in A356 aluminum alloy. The finite difference program of Navier-Stokes equation coupled with heat transfer and solidification has been developed to predict a filling pattern and the temperature distribution of SSM. The programdeveloped in this study gives die filling patterns of SSM and final solidifica-tion region.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.10a
• /
• pp.287-288
• /
• 2006

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.5
• /
• pp.1990-1995
• /
• 2012

This paper presents design methodology to determine the design parameters that affect the manufacture of aluminum forging piston using the FE simulation and the Taguchi method. Maximum forging load is used as the objective function, and preform, material temperature and draft angle are selected as the design parameters. Their combinations are implemented by orthogonal array, and forging load is evaluated through the simulation. From the analytic results of design parameters to minimize the load using signal to noise ratio, their optimal combinations are proposed. The proposed design methodology will be able to help in selecting proper preform among preforms and to be used in determining the optimal combination of the parameters in metal forming process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.6
• /
• pp.802-807
• /
• 2012

Self-piercing rivet is sheet joining method. It is being used more to join aluminum alloy sheets. Self-piercing riveting is a large-deformation process that involves piercing. The self-piercing rivet, under the press from the punch, pierces the top sheet and forms a mechanical interlock with the bottom sheet. In this study, forging process was designed for manufacturing self-piercing rivet. The forging process has been simulated by using commercial FEM code DEFORM-2D. In simulation of forging process for manufacturing rivet, process sequence, formability, forging load, and distributions of stress and strain were investigated. The suitable forging process could be designed by comparisons of simulation results. The developed process consists of four stages: upsetting, first chamfering, back extrusion, and second chamfering. The simulated results for forging process were confirmed by experimental trials with the same conditions.