• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.6_2
• /
• pp.1117-1125
• /
• 2023

The DC part of the DC microgrid power conversion system uses capacitors for buffers of charge and discharge energy for smoothing voltage and plays important roles such as high frequency component absorption, power balancing, and voltage ripple reduction. The capacitor uses an aluminum electrolytic capacitor, which has advantages of capacity, low price, and relatively fast charging/discharging characteristics. Aluminum electrolytic capacitors(AEC) have previous advantages, but over time, the capacity of the capacitors decreases due to deterioration and an increase in internal temperature, resulting in a decrease in use efficiency or an accident such as steam extraction due to electrolyte evaporation. It is necessary to take measures to prevent accidents because the failure diagnosis and detection of such capacitors are a very important part of the long-term operation, safety of use, and reliability of the power conversion system because the failure of the capacitor leads to not only a single problem but also a short circuit accident of the power conversion system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.2
• /
• pp.145-152
• /
• 2013

Electrolytic capacitors used for smoothing DC link voltage is one of the major root causes of fault in power electronic system. The aging of aluminum electrolytic capacitors is expressed by the increase of their equivalent series resistance (ESR) and the reduction of their capacitance. Thus, the proposed technique in this paper is to measure capacitance, by comparing energy loss of DC link capacitors with stator resistor in electric machine. Condition of DC link capacitors can be estimated from the capacitance decrease rate between initial and aged capacitors. The results show that the proposed technique provides an easy, widely applicable and simple low cost solution for detecting dc link capacitor degradation.

• Journal of the Korean institute of surface engineering
• /
• v.30 no.1
• /
• pp.44-56
• /
• 1997

Influence of electrochemical etching conditions on capacitance gain of aluminium electrolytic on capacitor foil has been investigated by etching cubic textured high purity aluminum foil in dilute hydrochloric acid. Uniformly distributed etch pit tunnels on aluminum surface have been obtained by pretreatment aluminium foil in 10% NaOH solution for 5 minutes followed by electrochemical etching. Electrostatic capacitance of etched aluminium foil anodized to high voltage increased with the increase of current density, total charge, temperature and concentration of electrolyte up to maximum CV-value and then deceased. Election optical observation of the etched foil revealed that the density of etch of etch pits increased with the increase of current density and concentration of electrolyte. this increase of etch pit density enlarged of the increase of capacitance. However, abnormal high current density and high electrolyte concentration induced the local dissolution of the foil surface which resulted the decrease of foil capacitance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.46-46
• /
• 1999

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.41-41
• /
• 2003

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.909-915
• /
• 2003

Anodic oxide films on aluminum play an important role as a dielectrics in aluminum electrolytic capacitor. In order to obtain the high capacitance, ZrO$_2$ films were coated on aluminum foils by sol-gel method and then, the properties of anodized films were studied. The coating and drying of the films were repeated 4-10 times and annealed at 300～$600^{\circ}C$ and the triple layer of ZrO$_2$/Al-ZrO$_{x}$ /Al$_2$O$_3$ was formed onto aluminum substrates after anodizing of ZrO$_2$/Al film. The thickness of $Al_2$O$_3$ layer was decreased with increasing the annealing temperature due to the densification of ZrO$_2$ film. The ZrO$_2$ films were crystallized even at 30$0^{\circ}C$ and showed nanocrystalline structure. The. capacitance of aluminum foil annealed at low temperature was higher than that at high temperature. The increase of capacitance was due to the high capacitance of ZrO$_2$ film annealed at low temperature. The capacitance of ZrO$_2$ coated aluminum increased about 3 times compared to that without a ZrO$_2$ layer after anodizing to 400 V. From these results, the aluminum foils with composite oxide layers are found to be applicable to the aluminum electrolytic capacitor.

• Korean Journal of Materials Research
• /
• v.25 no.2
• /
• pp.107-112
• /
• 2015

The oxide films formed on etched aluminum foils play an important role as dielectric layers in aluminum electrolytic capacitors. $Y_2O_3$-doped $ZrO_2$ (YZ) films were coated on the etched aluminum foils by sol-gel dip coating, and the electrical properties of YZ-coated Al foils were characterized. YZ films annealed at $450^{\circ}C$ were crystallized into a cubic phase, and as the $Y_2O_3$ doping content increased, the unit cell of $ZrO_2$ expanded and the grain size decreased. The etch pits of Al foils were filled by YZ sol when it dried at atmospheric pressure after repeating for several times, but this step could essentially be avoided when being dried in a vacuum. YZ-coated foils indicated that the specific capacitance and dissipation factor were $2-2.5{\mu}F/cm^2$ and 2-4 at 1 kHz, respectively, and the leakage current and withstanding voltage of films approximately 200 nm thick were $5{\times}10^{-4}A$ at 21 V and 22 V, respectively. After being anodized at 500 V, the foils exhibited a specific capacitance and dissipation factor of $0.6-0.7{\mu}F/cm^2$ and 0.1-0.2, respectively, at 1 kHz, while the leakage current and withstanding voltage were $2{\times}10^{-4}-3{\times}10^{-5}A$ at 400 V and 420-450 V, respectively. This suggests that YZ film is a promising dielectric that can be used in high voltage Al electrolytic capacitors.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.784-789
• /
• 1997

Aluminium solid electrolytic capacitor in which electroconducting polypyrrole(PPy) is used as an electrolyte is studied. Pyrrole(Py) is electrochemically synthesized using the etched and anodized aluminium foil electrode($Al_2O_3$) as an anode on which the thin layer of chemicalpolymerized PPy as a pre-coating layer is formed previously by chemical oxidative polymerization(CP). Investigating the effects of the polymerization conditions on the electrical characteristics of resulting capacitors, the capacitors which were obtained from the galvanostatic electrolysis of pyrrole containing sodium p-toluenesulfonate(TsONa) under the currents of $2.0{\sim}4.0mA/unit(6.5{\times}10mm)$, showed the most superior properties.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.592-593
• /
• 2012

Buck converter must operate at fairly high switching frequency for miniaturizing a whole circuit and achieving a fast response. However, at the conditions of low output voltage, high output current, and high switching frequency, the influence of parasitic elements to circuit operation will become extremely obvious. In this paper, it has been shown that these parasitic elements of output capacitor link the ripple of the output voltage. The MCP capacitors and aluminum electrolytic capacitors are applied to the buck converter and observed characteristics and the experimental results were reported.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.329-334
• /
• 2001

Microstructures of barrier-type oxide layers on aluminum was studied by XRD, TEM and RBS. Fer formation of oxide layer. aluminum was anodized in a boric acid solution. The thickness of the oxide film subjected to applied voltage increased linearly at ratio of 1.54nm/V. For oxide layer anodized at 300V, amorphous structure of oxide layer was not transformed after heat treatment at 50$0^{\circ}C$ , while for oxide layers anodized at higher voltages the amorphous structure crystallized into a ${\gamma}$-alumina without any heat treatment. It was also found that the amorphous structure of oxide layer formed at 100V transformed into crystalline structure by electron irradiation. The structure was identified as ${\gamma}$-alumina.