• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.154-159
• /
• 2003

In this paper, the design improvement for high speed train carbody, which made by aluminium alloy, was described. The design improvements was achieved in fields of economical efficiency, extrusion, welding, assembling, etc. This paper also describes the result of carbody test. The purpose of the test is to evaluate an safety under the load and operation condition. This strength test based on KTX and reference code is UIC 566 and JIS E 7105. The test results shows that aluminium carbody structural have enough strength for all part.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 동계 학술대회 논문집
• /
• pp.196-201
• /
• 2000

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 춘계학술대회 논문집
• /
• pp.557-558
• /
• 2009

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2000년도 추계학술대회 논문집
• /
• pp.133-141
• /
• 2000

Standardization EMU in comparison with the existing EMU has been largely changed the material and section profile of the structure as the Aluminium made. This study is analytically predicted the influence of inner noise in tunnel running when the above change is made.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.395-401
• /
• 2008

Since metallic foam will increase the performance of heat exchanger, it have caused many researcher's attention recently. Our research base on the model that metallic foams applied to heat exchanger. In this case, there is three kind of heat transfer mechanisms, heat conduction in fibers, heat transfer by conduction in fluid phase, and internal heat change between solid and fluid phases. In this paper we study both the hydraulic and thermal aspect performance. Pressure drop along air flow direction will be presented. As thermal aspect, we first discuss the acceptance of applying thermal equilibrium among the two phases. then to calculate the dimensionless temperature profile, the heat transfer coefficient and Nu number in 14 metallic foams(7 Aluminium foams, 7 FeCrAlY foams). All these discussion is based on the same velocity u=2 m/s.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.163-166
• /
• 1997

Aluminium foam material is a highly porous material having complicated cellular structure defined by randomly distributed air pores in metallic matrix. this structure gives the aluminium a set of properties which cannot be achieved by any of conventional treatments. The properties of aluminium foam material significantly depend on its porosity, so that a desired profile of properties can be tailored by changing the foam density. Melting method is the one of foaming processes, which the production has long been considered difficult to realize becaues of such problems as the low foamability of molten metal, the varying size of. cellular structures, solidification shrinkage and so on. These problems, however, have gradually been solved by researchers and some manufacturers are now producing foamed aluminum by their own methods. Most of all, the parameters of solving problem in electric furnace were stirring temperature, stirring velocity, foaming temper:iture, and so on. But it has not considered about those in induction heating, foaming velocity and foaming temperature in semi-solid state yet. Therefore, this paper presents the effects on these parameter to control cell size, quantity and distribution.

• 소성∙가공
• /
• 제11권8호
• /
• pp.701-709
• /
• 2002

Aluminium foam material is highly porous material, which has the complicated cellular structure defined by randomly distributed pores in metallic matrix. This structure gives the characteristic properties which cannot be achieved by any other conventional processes. As the properties of aluminium foam material significantly depend on its porosity, a desired profile of properties can be tailored by changing the foam density. But various defects lead to undesirable effects on the mechanical properties. Mechanical properties are dependent on cell sizes and aspect ratios. Therefore, this paper presents the effects of various processing parameters of various parameters on the mechanical properties. For the sake of this, combined stirring was used to fabricate aluminum foam materials by the parameters. Compression and bending tests were performed to investigate the effects of cell sizes and aspect ratios on the mechanical properties.

• 한국전기전자재료학회논문지
• /
• 제33권4호
• /
• pp.263-270
• /
• 2020

In this study, the physical mechanism and diffusion effects in aluminium implanted silicon was investigated. For fabricating power semiconductor devices, an aluminum implantation can be used as an emitter and a long drift region in a power diode, transistor, and thyristor. Thermal treatment with O₂ gas exhibited to a remarkably deeper profile than inert gas with N₂ in the depth of junction structure. The redistribution of aluminum implanted through via thermal annealing exhibited oxidation-enhanced diffusion in comparison with inert gas atmosphere. To investigate doping distribution for implantation and diffusion experiments, spreading resistance and secondary ion mass spectrometer tools were used for the measurements. For the deep-junction structure of these experiments, aluminum implantation and diffusion exhibited a junction depth around 20 ㎛ for the fabrication of power silicon devices.

• 한국표면공학회지
• /
• 제33권5호
• /
• pp.309-318
• /
• 2000

The 6063 Aluminium alloy were electrocolored and anodized at the same time in addition of $CoSO_4$, $FeSO_4$, in the electrolyte and investigated by AES/SAM. It was found that the thickness of anodic oxide film is increased linearly in DC type, and DC combined AC type, the more ratio of anodic Portion in AC, the more increased of anodic film thickness. The color of anodic film was changed from silver to yellow when the increase of the ratio of cathodic portion in AC. Also the increase of $CoSO_4$, $FeSO_4$ in the electrolyte, the coloring time is decreased. From the AES/SAM results, the element of anodic oxide film are Al,O and S. The result of depth profile, the most of the S distributed on the surface and the more S is in DC combined AC type than only DC type.

• 한국주조공학회지
• /
• 제12권3호
• /
• pp.220-229
• /
• 1992

The degree of purification and the macrostructure of high purity aluminium were studied through the alternate stirring method in order to improve the nonuniformity of solute concentration in the unidirectional stirring method. The $2^3$ factorial design was done to examine the effects of experimental factors more qualitatively. In the relatively low stirring speed of 1500 rpm with alternate stirring mode, the uniform solute profile and refined grain structure were obtained due to strong washing effect and turbulent fluid flow. It was induced by the transition of the momentum boundary layer by alternation of the stirrer. It was concluded from this study that the alternate stirring mode was more effective to obtain the uniformity of solute even in the stirring speed of 1500 rpm. But the degree of purification decreased below the critical alternating period. When 2N(99.8wt.%) aluminium was used as the starting material the morphology of solid-liquid showed the cellular shape and the columnar grains were inclined to the direction of rotation. This inclined grain growth resulted from the difference of relative velocities of solid and liquid. The inclined angle was increased as the stirring speed increased and solidification proceeded. In the case of 4N aluminium, there was no inclined grain growth and it was confirmed from the macrostructure and SEM work that the morphology of solid-liquid interface was planar. From the factorial design, it was found that the alternate stirring mode showed poorer purification effect than that of unidirectional stirring mode at low speed(500 rpm). In addition, the factor that had the most significant effect on the degree of purification was the stirring speed.