• Journal of the Korean Ceramic Society
• /
• v.35 no.6
• /
• pp.551-558
• /
• 1998

Detection of microcrack in {{{{ {Al }_{2 } {O }_{3 } }} ceramics were studided by AE(acoustic emission) technique with 4-point bending test in order to evaluate the fracture process and formation of microcrack. Fully-dense alu-mina ceramics having a different grain size were fabricated by varing the hot-pressing temperature. The grain size of alumina increased with increasing the hot-pressing temperature whereas the bending strength decreasd. The microcracks were observed by SEM and TEM. The generation of AE event increased with increasing the applied load and many AE event was generated at maximum applied load. Alumina with smaller grain size shows the generation of many AE event resulting in an increase of microcrack formation. An intergranular fracture is predominantly observed in fine-grained alumina whereas intragranular fracture occurs predominantly in coarse-grained alumina,. Analysis of micorstructure and AE prove that primary mi-crocracks occur within grain-boundaries of alumina. The larger microcracking were formed by the growth and/or coalesence of primary microcracks. Then the materials become to fracuture by main crack gen-eration at the maximum applied load.

• Journal of the Korean Ceramic Society
• /
• v.33 no.9
• /
• pp.1045-1049
• /
• 1996

Pressureless-sintered polycrystalline alumina and carbon steel were joined with Ag-33.5Cu-1.5Ti (wt%) brazing alloy. SEM observation revealed that two reaction layers with different thicknesses were continuously formed between the alumina and the brazing alloy. A thick layer formed on the brazing alloy side was identified as Ti3(Cu0.93Al0.07)3O phase with diamond cubic structure. Another thin layer adjacent to the alumina was revealed as $\delta$-TiO phase of which the crystal structure was HCP with a lattice parameter of a0=0.419 nm and c0=0.284 nm. It was confirmed using XPS analysis that $\delta$-TiO was formed directly by a redox reaction of alumina with titanium ir, molten brazing alloy.

• Journal of the Korean Ceramic Society
• /
• v.28 no.12
• /
• pp.1019-1025
• /
• 1991

The effect of dissolved Ca ion from plaster mold during slip casting on the microstructure and fracture toughness of high-purity sintered alumina were investigated. When the alumina slip containing 1000 ppm MgO was casted on a calcined alumina mold, the sintered compact had a homogeneous microstructure with equiaxed grains. However, when the same slip was casted on a plaster mold, the sintered compact consisted of the mixture of equiaxed and elongated grains. This inhomogeneous microstructure was also observed in the sintered alumina doped with 100o ppm MgO and 100 ppm CaO whose compact was prepared on the calcined alumina mold indicating that the inhomogeneity was caused by CaO. It was found that the specimen containing both MgO and CaO had higher fracture toughness than that containing MgO only. The enhanced fracture toughness by CaO is probably due to the crack deflection along the boundaries of the elongated grains.

• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.396-401
• /
• 2013

The size of various alumina ceramics used in the semiconductor and display industries must be increased to increase the size of wafers and panels. In this research, large alumina ceramics were fabricated by pressure-vacuum hybrid slip casting (PVHSC) employing a commercial powder, followed by sintering in a furnace. In the framework of the PVHSC method, the consolidation occurs not only by compression of the slip in the casting room but also by suction of the dispersion medium from the casting room. When sintered at $1650^{\circ}C$ for 4 h, the fabricated large-size alumina ($1,550{\times}300{\times}30mm^3$) exhibited a dense microstructure corresponding to more than 99.2% of the theoretical density and a high purity of 99.79%. The flexural and compressive strengths of the alumina plate were greater than 340 MPa and 2,600 MPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.824-831
• /
• 2000

Alumina tapes, having various ratios of alumina to alumina＋binder＋plasticizer (a/(a＋o)) and binder to binder＋plasticizer(b/(b＋p)), were prepared by the tape casting method. The tapes were thermocompressed varying the thermocompression parameters such as temperature, pressure, and duration time. Among the parameters, the pressure was the most influential to the tape packing density. The packing density varied in two different ways depending on the a/(a＋o) ratio. For the tapes having low a/(a＋o) ratio, a saturation density was reached by applying very a low pressure of 1 MPa. For tapes with high a/(a＋o), on the contrary, the saturation density was obtained at a relatively high pressure. These different responses to the pressure are attributed to the fact that the rearrangement of alumina particles by the pressure becomes easy as an organic content in the tapes is high.

• Tribology and Lubricants
• /
• v.21 no.5
• /
• pp.216-220
• /
• 2005

The sliding wear behaviors of three different compositions of novel low temperature degradation-free zirconia/alumina (LTD-free Z/A) composites were examined in a ceramic-ceramic contact pair. The wear tests were performed by using a pin-on-disk type wear tester in a linear reciprocal sliding motion with a line contact in both dry and bovine serum lubricated conditions at room temperature. From the results of dry sliding wear tests, Z/A#1((5.3Y, 4.6Nb)-TZP/80 $vol\%Al_2O_3$) showed the best wear resistance among three kinds of LTD-free Z/A composites. For the bovine serum lubricated sliding wear tests, wear was too little to be measured for all kinds of Z/A composites. These novel LTD-free Z/A composites having excellent wear resistance demonstrated a potential as the alternative materials for the ceramic-ceramic contact pairs of femoral head and acetabular liner in total hip replacement.

• Journal of the Korean Ceramic Society
• /
• v.52 no.4
• /
• pp.248-252
• /
• 2015

Natural materials often have unique mechanical properties, such as the hierarchical structure of nacre formed through mineral bridges or asperities created between an inorganic particle and a natural-layer surface. As these asperities produce an exceptional shear resistance, in this study, we aimed to emulate the natural structure of nacre by synthesizing inorganic asperities and mineral bridges with different temperatures in the range of $1100-1300^{\circ}C$ and clay contents from 10 - 50 wt%. Following the infiltration of methyl methacrylate, we measured the mechanical properties to assess whether they were improved by the asperities. It was confirmed that the asperities improved the bending strength by 10%, and the anchoring effect was observed on the fracture surface.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.939-945
• /
• 2004

Glasses of $SiO_2-B_{2}O_3-Al_{2}O_3-CaO-La_{2}O_3$ with various amounts of $La_{2}O_3$ were infiltrated into a porous alumina to make an alumina-glass composite. The infiltration characterization and bending strength of the composite were examined in terms of glass composition. $La_{2}O_3$ in the glass decreased the high temperature viscosity and this enhanced the wetting behaviour of this glass to alumina, and made glass infiltration easier. The infiltrated glass dissolved the alumina skeleton, and $Al_{2}O_3$ component in the glass melt reprecipitated on the alumina. The grain growth occurred to a specific crystal direction. The glass containing $20mole\%$ of $La_{2}O_3$ was crystallized after infiltration, and this enhanced the bending strength of the composite.

• Journal of Technologic Dentistry
• /
• v.46 no.3
• /
• pp.107-113
• /
• 2024

Purpose: This study aimed to develop dental alumina ceramic dressers, evaluate their abrasive wear characteristics based on particle size, and identify dental dressers with optimal particle size and performance. Methods: Commercial ceramic dressers (n=5) were selected as the control group, whereas alumina ceramic dressers with 80-grit and 120-grit particles were fabricated as the experimental groups (n=5 each). Prepared specimens were assessed for surface roughness, wear resistance, and abrasiveness against a wear-inducing element (SUS304 stainless steel ball). Means and standard deviations were calculated for each test. Statistical analysis was performed using the Kruskal-Wallis H test with Bonferroni correction (α=0.05) via SPSS Statistics ver. 23.0 (IBM). Results: Surface roughness was highest in the 80-grit group (22.734±1.308 ㎛), followed by 120-grit group (21.804±0.785 ㎛), and lowest in control group (15.782±0.223 ㎛). Wear resistance was greatest in 120-grit group (0.007±0.002 g), followed by the 80-grit group (0.007±0.004 g), and lowest in the control group (0.370±0.010 g). Furthermore, abrasiveness against the wear-inducing element (SUS304 stainless steel ball) was highest in 120-grit group (0.017±0.003 g), followed by the 80-grit group (0.015±0.003 g), and lowest in control group (0.010±0.001 g). Conclusion: Based on the combined results of surface roughness, wear resistance, and abrasiveness against a wear-inducing element, the newly developed alumina ceramic dressers show promise for clinical application.

• Journal of the Korean Ceramic Society
• /
• v.33 no.8
• /
• pp.849-854
• /
• 1996

boehmite which is the by-product in alcohol process contains anions such as $Cl^-,{NO_3}^-.or\; CH_3COO^-$ Influe-nce of these anions was studied on properties of $\alpha$-alumina powders prepared by treating the transformed ${\gamma}$-alumina with the alumina sol and $\alpha$-alumina seeds (d_{50}=0.36\mu\textrm{m}$) Disperal 20/1 and 10/1 containing $Cl^-$ produced spherical powder Disperal 20/2 with ${NO_3}^-$ produced equiaxed powder and Disperal 10/3 with $CH_3$ $COO^-$ irregular shaped and sized powder. All of these $\alpha$-alumina powders were submicron. Although the green density of the alumina powder derived from Disperal 10/1 by calcination at $1200^{\circ}C$/1h. was 53% it did not sinter even at $1550^{\circ}C$ for 2h. which implies that its d50 is greater than $3\mu\textrm{m}$. The others gave green densities in the range of 44~47% but they sintered as well as the AKP-30 at $1500^{\circ}C$/2 h or $1550^{\circ}C$/2 h.