• 한국구조물진단유지관리공학회 논문집
• /
• 제5권4호
• /
• pp.169-176
• /
• 2001

This study aims to present a more reasonable control value than the exiting one by comparing and analyzing control values and field instrument8tion values of the whole excavation depth of the four case sites, using geometric averaging as a statistical method. The range of the study is confined to the horizontal displacement of braced excavation walls among a variety of items, prescribed in the control values by approximately of the allowable and design values, and by safety factors. As a result, it is desirable to revise 70, 90, and 100 percent of LEVEL I, II, and III, respectively. The horizontal displacement values of the allowable and design values approximations should change to 104, 133, and 148 percent of the allowable and design values, respectively. In addition, modifying the horizontal displacement control value of the braced excavation walls is not needed. The horizontal displacement value, presented in the control value as a safety factor, is now 1.19, as it has a slight difference from the present value.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1580-1587
• /
• 2005

To calculate the long-term allowable strength of geosynthetic reinforcement, replacement method was recommended. The isochronous creep curve by S. Turner was used to define the relation between creep strain and allowable strength. In isochronous curve at given time, one can read the allowable strength at allowable creep strain. The allowable strain gets from specification by directors or manufacturers according to the allowable displacement of reinforced structures. The allowable strength can be determined in relation to the allowable horizontal displacement each structures case by case. The effect of install damage on isochronous behaviors of geosynthetic reinforcement was little. In previous study, install damage increase the creep strain slightly. And the degradation was not identified. But it is supposed that degradation increase the creep strain. In conclusion, The recommended model to determine long-term allowable strength of geosynthetic reinforcements considering tensile deformation of reinforcement and soil is fit for proper, correct and economic design for reinforced earth walls.

• 한국지반환경공학회 논문집
• /
• 제9권7호
• /
• pp.13-23
• /
• 2008

본 연구에서는 모래다짐말뚝으로 개량된 점성토 지반에 고성토시 발생될 수 있는 측방유동과 교대의 안정성을 파악하기 위하여 원심모형실험과 수치해석을 수행하였다. 원심모형실험과 수치해석은 교대 배면구간을 EPS로 성토한 경우(Case 1)와 토사로 성토한 경우(Case 2)에 대하여 수행하였으며, 모형실험시 교대와 성토체에 potentiometer를 설치하여 교대상부의 수직변위와 수평변위 및 성토체의 수직변위를 측정하였다. 원심모형실험결과 Case 1에서 교대의 수평변위는 1.4cm 정도로 해석결과와 거의 일치하며, 허용기준을 만족하는 것으로 나타났다. 반면, Case 2에서 교대의 수평변위는 12cm 정도로 해석결과에 비해 18% 정도 크게 평가되었으며, 허용기준을 초과하는 것으로 나타났다. 해석결과 Case 1에서 말뚝의 최대수평변위는 1.26cm로 허용 수평변위 기준(1.5cm)을 만족하는 것으로 나타난 반면, Case 2에서 말뚝의 최대 수평변위는 1.005m로 허용기준을 크게 초과하는 것으로 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권3호
• /
• pp.194-204
• /
• 1998

This study was performed to suggest the proper maintenance method for the deteriorated gerber type PC box girder bridge by using the long term displacement monitoring data. For this study, the monitoring system which can measure the long term displacement and the concrete surface temperature was designed and operated. From the measurement and structural analysis results, the cause of the permanent deformation which the bridge has already was estimated, and based on this result, the allowable permanent displacement value at the hinge was suggested. From this study, it was known that the long term monitoring system can be applied to the active maintenance of the deteriorated bridge and the suggested allowable permanent displacement could be used for the maintenance of the bridge.

• 한국산학기술학회논문지
• /
• 제20권4호
• /
• pp.534-544
• /
• 2019

IPM Bridge는 파일벤트가 지표면으로부터 돌출되어, 교대의 과도한 변위가 유발될 수 있다. 본 연구에 사용된 교량의 형상은 IPM Bridge의 설계지침에 제시된 최대 적용 조건인 경간 120.0m, 사각 30도, 파일벤트의 돌출높이 최대 10.0m를 적용하였다. 이 교량모델을 이용하여, IPM Bridge의 최대 경간 적용조건에 따른 최대 변위를 산정하였으며, Bozozuk가 제시한 허용 변위에 근거하여 IPM Bridge의 수평변위의 안정성을 검토하였다. IPM Bridge의 최대 수평변위는 여름철의 팽창 조건보다는 겨울철의 수축 조건에서 더 크게 산정되었으며, 수평변위는 사각보다는 교량의 길이에 더 큰 영향을 받는 것으로 나타났다. 그리고 수직 변위는 사각과 연장에 큰 영향을 받지 않는 것으로 나타났다. 경간의 증가에 따라 수평변위가 크게 증가되었으며, 연장 120.0m에서의 수평변위는 Bozozuk가 제시한 허용 변위를 초과하는 것으로 나타났다. 하지만, 파일벤트에 발생되는 모멘트가 소성모멘트를 초과하지는 않았다. IPM Bridge는 설계지침에 제시된 최대 적용조건인 파일벤트의 돌출높이 10.0m, 연장 120.0m에서는 수평변위가 과도하게 발생될 수 있으므로, 설계단계에서 면밀한 검토가 필요하다.

• 산업기술연구
• /
• 제20권A호
• /
• pp.257-267
• /
• 2000

It was difficult to apply conventional excavation methods in some sections from Seoul to Pusan high speed rail road construction of 1 lot 2, due to highway concrete road, gas pipe, water pipe and nearby factories with automatic control system machine. To excavate safely and efficiently in these sections new blast patterns were employed within allowable blast vibration level, by test blast and controlled vibration by sequential blast. Behaviors of the rock mass including convergence and displacement around tunnel were measured with construction works and the crack width in concrete wall was also monitored for controlling allowable limits. The results can be summarized as follow : 1. The allowable blast vibration level in structure site is less 1.0cm/sec for highway concrete, 0.5 cm/sec for gas pipe, water pipe and building housing and 0.3 cm/sec for automatic control system machine. 2. The convergence displacement, single rod extensometer and multi rod extensometer around tunnel and cracks in concrete wall were measured, it was confirmed that the measured values were converged within allowable level. 3. The empirical formular of ground vibrations with 90% confidence lines for PD-3 was given as follow. $$V_{90%}=45.549({\frac{D}{\sqrt{W}}})^{-1.353}$$

• 한국안전학회지
• /
• 제33권2호
• /
• pp.145-151
• /
• 2018

In this study, the track-bridge interaction analysis was performed using an analytical model considering the track structure, thereby taking into account the linear conditions (R=650 m, cant variation $160{\pm}60mm$) and the dynamic characteristics of the bridge. As a result of the study, the allowable speed on the example bridge considered was calculated at 200 km/h based on vertical deflection, vertical acceleration, and irregularity in longitudinal level, but was also evaluated at 170km/h based on the coefficient of derailment, wheel load reduction, and lateral displacement of the rail head. It is considered desirable to set the speed 170km/h to the speed limit in order to secure the safety of both the bridge and the track. It is judged that there will be no problems with ensuring rail protection and train stability in the speed band.

• 지질공학
• /
• 제30권1호
• /
• pp.59-69
• /
• 2020

CPR 시험말뚝에 대해 인발재하시험을 실시하고, 하중-변위 곡선과 하중-침하량 곡선을 분석한 후 항복하중과 허용지지력을 산정하여 주면마찰력을 평가하였다. 하중-변위 곡선으로부터 분석된 CPR 시험말뚝의 결과에 의하면, CPR 시험말뚝의 직경이 큰 경우의 항복하중과 허용지지력이 작은 경우보다 약 1.4배 이상 크게 나타났다. 하중-침하량 곡선으로 부터 분석된 결과에 의하면, CPR 시험말뚝의 직경 D500의 허용지지력이 D400보다 약 1.2~2.1배 큰 것으로 나타났다. 하지만, Fuller 분석에 의해 산정된 허용지지력은 P-S 곡선과 log P - log S 곡선에 의해 산정된 허용지지력과 큰 차이를 보여, Fuller 분석에 의한 허용지지력 산정은 적절하지 않은 것으로 판단되었다.

• 한국지진공학회논문집
• /
• 제22권5호
• /
• pp.299-309
• /
• 2018

Now that problems with force-based seismic design have been clearly identified, design is inclined toward displacement-based methods. One such widely used method is Direct-Displacement-Based Design (DDBD). Yet, one of the shortcomings of DDBD is considering higher-mode amplification of story shear, moments, and displacements using equations obtained from limited parametric studies of regular planar frames. In this paper, a different approach to account for higher-mode effects is proposed. This approach determines the lateral secant stiffness of the building frames that fulfill the allowable inter-story drift without exceeding the desired story displacements. Using the stiffness, an elastic response spectrum analysis is carried out to determine elastic higher-mode force effects. These force effects are then combined with DDBD-obtained first-mode force effects using the appropriate modal superposition method so that design can be performed. The proposed design procedure is verified using Nonlinear Time History Analysis (NTHA) of twelve planar frames in four categories accounting for mass and stiffness irregularity along the height. In general, the NTHA response outputs compared well with the allowable limits of the performance objective. Thus, it fulfills the aim of minimizing the use of NTHA for planar frame buildings, thereby saving computational resources and effort.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1149-1155
• /
• 2007

The transition area between a bridge and an earthwork is one of the weakest area of track because of the track geometry deterioration caused unequal settlement of backfill of abutment. In case of a ballastless track, the approach slab is installed to prevent the phenomenon. But, if there is occurred the inclined displacement on the approach slab by a settlement of the foundation or formation, the track is also under the inclined displacement. And this defect causes reducing the running stability of a vehicle, the riding comfort of passengers, and the deteriorations of track by excessive impact subjected to the track. In this study, parametric studies were performed to know what is the allowable displacement limit on the approach slab to avoid such a bad effect. The length and amount of unequal settlement of the approach slab was adopted as parameter for numerical analysis. And car body accelerations, variations of wheel force and rail stress and uplift force induced on a fastener clip are investigated. From the result, resonable settlement limits of an approach slab according to slab length was suggested.