• Journal of Powder Materials
• /
• v.26 no.3
• /
• pp.220-224
• /
• 2019

The aluminum (Al)/copper oxide (CuO) complex is known as the most promising material for thermite reactions, releasing a high heat and pressure through ignition or thermal heating. To improve the reaction rate and wettability for handling safety, nanosized primary particles are applied on Al/CuO composite for energetic materials in explosives or propellants. Herein, graphene oxide (GO) is adopted for the Al/CuO composites as the functional supporting materials, preventing a phase-separation between solvent and composites, leading to a significantly enhanced reactivity. The characterizations of Al/CuO decorated on GO(Al/CuO/GO) are performed through scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy mapping analysis. Moreover, the functional bridging between Al/CuO and GO is suggested by identifying the chemical bonding with GO in X-ray photoelectron spectroscopy analysis. The reactivity of Al/CuO/GO composites is evaluated by comparing the maximum pressure and rate of the pressure increase of Al/CuO and Al/CuO/GO. The composites with a specific concentration of GO (10 wt%) demonstrate a well-dispersed mixture in hexane solution without phase separation.

• Journal of the Korean Ceramic Society
• /
• v.30 no.10
• /
• pp.811-818
• /
• 1993

Al2O3/ZrO2-Spinel composites were prepared by infiltrating magnesium sulfate solution into the porous preform made from Al2O3-20wt% ZrO2 composite powders derived through an emulsion route. The microstructure and composition of the modified composites could be controlled by manipulating the presingtering temperature of the preform, infiltration time, and so on. It was found that spinel phases were concentrated near the surface than in the interior of the Al2O3/ZrO2-Spinel composites infiltrated for 6hrs, while spinel phases were uniformly distributed in the comosites infiltrated for 2 days. The relative density and fracture toughness of the composite infiltrated for 6 hrs were 98.6% and 7.2MN/m3/2, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.408-409
• /
• 2007

Al-doped p-type ZnO films were fabricated on n-Si (100) and homo-buffer layers in pure oxygen at $450^{\circ}C$ by RF magnetron sputtering. Target was ZnO ceramic mixed with 2wt% $Al_2O_3$. XRD spectra show that the Al-doped ZnO thin films have ZnO crystal structure and homo-buffer layers are beneficial to Al-doped ZnO films to grow along c-axis. Hall Effect experiments with Van der Pauw configuration show that p-type carrier concentrations are ranged from $1.66{\times}10^{16}\;to\;4.04{\times}10^{18}cm^{-3}$, mobilities from 0.194 to $2.3cm^2V^{-1}s^{-1}$ and resistivities from 7.97 to $18.4{\Omega}cm$. P-type sample has density of $5.40cm^{-3}$ which is smaller than theoretically calculated value of $5.67cm^{-3}$. XPS spectra show that O1s has O-O and Zn-O structures and A12p has only Al-O structure. P-ZnO:Al/n-ZnO:Al junctions were fabricated by magnetron sputtering. V-I curves show that the p-n junctions have rectifying characteristics.

• Journal of the Korean Magnetics Society
• /
• v.8 no.1
• /
• pp.27-33
• /
• 1998

We have investigated tunneling magnetoresistance (TMR) properties of Fe/$Al_2O_3$/Co magnetic trilayer junctions sputtered on single-crystal Si (001) substrates. $Al_2O_3$ layers with thicknesses of 50~200 $\AA$ were deposited directly on the bottom ferromagnetic layer by a reactive rf sputtering. For comparsion, we prepared Pt/$Al_2O_3$/Pt tunnel junctions whose current-voltage (I-V) characteristics measured at 300 K indicated that reactively sputtered $Al_2O_3$ is a particularly good material for thin insulating barriers and allows us to form pinhole-free tunnel barriers. The magnetic tunnel junctions exhibit changes of tunnel resistance of about 0.1% at 300 K with an applied magnetic field and it was found that most junctions with Co as a top electrode have rather good I-V and TMR characteristics compared to those with Fe as a electrode. These results were discussed in relation to interfacial on the basis of those for Pt/$Al_2O_3$/Pt.

• Journal of the Korean Ceramic Society
• /
• v.28 no.4
• /
• pp.338-346
• /
• 1991

The alumina-titania composite powders coated with Al2O3 were prepared by the method of hydrolysis-deposition of mixed aluminium salt solution of Al2(SO)4-Al(NO3)3-Urea. The effects of coating-process parameters on the characteristics of coated composite powders were also investigated. As the content of TiO2 dispersed in deionized water increased, the coated composite powders were found to be more uniform in size and unagglomerated. When TiO2 powders were coated for 30 min, the optimum TiO2 content in the coating process was 400 mg/ι. The size of TiO2 particle was increased approximately from 0.7${\mu}{\textrm}{m}$ to 1.0${\mu}{\textrm}{m}$ through coating of Al2O3. The IEP of coated composite powders was pH=8.3 identical to the value of aluminium hydroxides and the zeta-potential showed nearly similar values each other. When heat treating coated composite powders at 130$0^{\circ}C$, only two phases of TiO2(rutile) and Al2TiO5 were observed. These results showed that the suface of TiO2 could be uniformly coated with the aluminium hydroxide.

• Journal of the Korean Ceramic Society
• /
• v.37 no.4
• /
• pp.359-367
• /
• 2000

Particulate composites of Al2O3/SiC, Al2O3/ZrO2 and Al2O3/ZrO2/SiC have been fabricated to investigate their R-curve behaviors and toughening mechanisms. Al2O3 containing 30 vol% SiC particles of 3${\mu}{\textrm}{m}$ showed rising R-curve behavior owing to the strong crack bridging by SiC particles. The fracture toughness reached 9.1 MPa {{{{ SQRT {m} }} at the crack length of 1000${\mu}{\textrm}{m}$. On the other hand, ZrO2-toughened Al2O3 had a high flat R-curve since it rose steeply in the short crack region due to the well known transformation toughening. For Al2O3/ZrO2/SiC composites, the R-curve behavior was similar to that of Al2O3/SiC but with slightly higher toughness. The SiC particles in this composite decreased the amount of transformable tetragonal phase to reduce the effect of transformation toughening by 50%. It was also found that the fracture toughness of this composite with two different toughening mechanisms was markedly lower than that estimated by the simple addition of two contributions.

• Journal of the Korean Vacuum Society
• /
• v.22 no.3
• /
• pp.119-125
• /
• 2013

In this study, we studied the properties of ZnO(Al) and ZnO(AlGa) thin film according to film thickness deposited on SLG by In-line magnetron sputtering system. XRD, FESEM, 4-point probe, Hall measurement system and UV/Vis-NIR spectrophotometer were employed to analyze the properties of ZnO(Al) and ZnO(AlGa) thin film. The all films exhibited (002) preferential orientation with clear peak shape and high intensity. The carrier concentration and Hall mobility of ZnO(Al) and ZnO(AlGa) thin film were improved with increasing thickness. The resistivity of both films decreased when the film thickness was raised from 500 nm to 1,450 nm. And then relatively the resistivity of ZnO(AlGa) film was lower than that of ZnO(Al) film. The transmittance of the films decreased with increasing film thickness but all films exhibited optical transmittances of over 83.3% in the visible region.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.701-704
• /
• 2001

The dielectric and sintering properties of LaAlO$_3$ceramics synthesised with La$_2$O$_3$-Al$_2$O$_3$(LAO) and La$_2$O$_3$-Al(OH)$_3$(LAH) were investigated. In case of LAH samples, a single phase of LaAlO$_3$powders was formed at 100$0^{\circ}C$, density of the ceramics sintered at 140$0^{\circ}C$ was 6.41g/㎤, and the dielectric constant and loss were 22.4 and 0.003, respectively. In case of LAO samples, a single phase of LaAlO$_3$powders was formed at 130$0^{\circ}C$, density of the ceramics sintered at 150$0^{\circ}C$ was 6.35g/㎤, and the dielectric constant and loss were 22.16 and 0.009, respectively.

• Journal of Powder Materials
• /
• v.21 no.5
• /
• pp.377-381
• /
• 2014

This work describes the coloration, chemical stability of $SiO_2$ and $SnO_2$-coated blue $CoAl_2O_4$ pigment. The $CoAl_2O_4$, raw materials, were synthesized by a co-precipitation method and coated with silica ($SiO_2$) and tin oxide ($SnO_2$) using sol-gel method, respectively. To study phase and coloration of $CoAl_2O_4$, we prepared nano sized $CoAl_2O_4$ pigments which were coated $SiO_2$ and $SnO_2$ using tetraethylorthosilicate, $Na_2SiO_3$ and $Na_2SiO_3$ as a coating material. To determine the stability of the coated samples and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Blue $CoAl_2O_4$ solutions were tuned yellow color under all acidic/basic conditions. On the other hand, the chemical stability of $SiO_2$ and $SnO_2$-coated $CoAl_2O_4$ solution were improved when all samples pH values, respectively. Phase stability under acidic/basic condition of the core-shell type $CoAl_2O_4$ powders were characterized by transmission electron microscope, X-ray diffraction, CIE $L^*a^*b^*$ color parameter measurements.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.95-96
• /
• 2000

The effect of $Al_2O_3$ on the dielectric constant and the coefficient of thermal expansion of lead borosilicate glasses for the application of PDP glass paste was investigated. Measurements were made theoretically by using empirical equations on the composition of the of glasses in which the $PbO/Al_2O_3$, $B_2O_3/Al_2O_3$ and $SiO_2/Al_2O_3$ ratios were systematically varied. As a result, with increasing $PbO/Al_2O_3$ the thermal expansion coefficient and the dielectric constant noticeably increased, while the change of $B_2O_3/Al_2O_3$ and $SiO_2/Al_2O_3$ ratios did not affect those properties of the glasses.