• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.15 no.3
• /
• pp.1-5
• /
• 2007

In this paper, effective thermal conductivities of water-based Al203-nanofluids with low concentration from 0.01 vol. % to 0.3 vol. % are experimentally obtained by transient hot wire method (THWM). The water-based Al203-nanofluids are manufactured by two-step method which is widely used. To examine suspension and dispersion characteristics of the water-based A1203-nanofluids, Zeta potential as well as transmission electron micrograph (TEM) is observed. We confirm the manufactured Al203-nanofluids have good suspension and dispersion. The effective thermal conductivities of the water-based Al203-nanofluids with low concentration are enhanced up to 1.64% compared with that of DI water at $21^{\circ}C$. In addition, experimental results are compared with theoretical results from Jang and Choi model.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1056-1059
• /
• 2001

These days, as dynamic function and special properties to compare traditional material, $Al_20_3$ ceramic use all over the industry. But it is very difficult to process because of high hardness and brittleness. Therefore, in this paper, it was investigated that laser process parameter which can produce appropriate quality of $Al_20_3$ ceramic microhole machining.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1997.02a
• /
• pp.203-203
• /
• 1997

• Journal of Korea Foundry Society
• /
• v.43 no.4
• /
• pp.203-209
• /
• 2023

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.142-142
• /
• 1999

열역학적 평형하에서 금(Au)은 사파이어(Sapphire: 다결정 Al203)와 반응을 하지 않으므로 접합성이 약하나 사파이어표면을 Ar 이온으로 에칭한후 금박막을 증착하였을 때 후 열처리 없이도 대단히 강한 접합(>70MPa)이 얻어졌다. 접합기구를 규명하기 위해 고 해상도 Auger 전자광분광기로 금/사파이어 쌍의 입계에 Ai-Al-O 화합물이 1-2 원자층 범위내에서 형성되어 있고 7KeV의 Ar 이온에너지로 3분간 조사하을 때 사파이어표면에 환원으로 인한 금속알루미늄이 형성되어 있음이 발견되었다. 이 이온조사로 인한 환원은 선택적 에칭으로 인한 것으로 TRIM 계산결과와도 일치하는 것이다. 따라서 금박막과 이온조사된 사파이어 사이의 강한 접합은 이온조사로 인한 사파이어 표면에 충돌할 때의 운동 에너지가 구동력이 되어 Au-Al-O 화합물의 형성으로 결론될 수 있다.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.203-206
• /
• 2006

Femtosecond laser-induced nano-patterning of an Al surface coated on a slide glass is reported in this paper. It was found that the period of the laser-induced nano-patterning was much dependent on the incident laser power and pulse number. Through finely adjusting the laser power and pulse number, uniform nano-patterns could be formed on the Al surface. It is based on the interference of the incident laser beam with some form of a surface scatted electromagnetic wave. It was also found that an Al oxide layer played an important role in forming the nano-patterning on the Al surface.

• Journal of Korea Foundry Society
• /
• v.12 no.3
• /
• pp.203-209
• /
• 1992

Directional solidification of Al-Ti peritetic alloys was carried out using Upward Continuous Casting Process. The morphology of a solid-liquid interface and solidification microstructures were investigated under various crystal growing conditions. The experimental results were compared with those attained by the Bridgman method. The cell spacing of the Al-Ti peritetic alloys and the primary dendrite arm spacing of the Al-Ti peritetic alloys decreased with an increase in pulling speed. The primary ${\beta}$ phase of the Al-Cr and Al-Ti peritectic alloys did not appear in solidification microstructures because of the depleted solute contents in the melt ahead of the solid-liquid interface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.4
• /
• pp.203-208
• /
• 2014

In this study, Sputtering method was used to grow Al-dopes ZnO films on a CIGS absorber layer, in order to examine the effect of TCO on properties of CIGS solar cell devices. Structural, electrical and optical properties were investigated by varied thickness of Al-dopes ZnO films. Also, relation to the application as a window layer in CIGS thin film solar cell were studied. It was found that the electrical and structural properties of ZnO:Al film improved with increasing its thickness. However, the optical properties degraded. Jsc of the fabricated CIGS based solar cells was significantly influenced by the variation of the ZnO:Al window layer thickness. Because ZnO:Al window layer is one of the Rs factors in CIGS solar cell. Rs has the biggest influence on efficiency characteristic. In order to obtain high efficiency of CIGS solar cell, ZnO:Al window layer should be fabricated with electrically and optically optimized.

• Journal of Powder Materials
• /
• v.17 no.3
• /
• pp.203-208
• /
• 2010

A new High Frequency Induction Heating (HFIH) process has been developed to fabricate dense $Al_2O_3$ reinforced with Fe-Ni magnetic metal dispersion particles. The process is based on the reduction of metal oxide particles immediately prior to sintering. The synthesized $Al_2O_3$/Fe-Ni nanocomposite powders were formed directly from the selective reduction of metal oxide powders, such as NiO and $Fe_2O_3$. Dense $Al_2O_3$/Fe-Ni nanocomposite was fabricated using the HFIH method with an extremely high heating rate of $2000^{\circ}C/min$. Phase identification and microstructure of nanocomposite powders and sintered specimens were determined by X-ray diffraction and SEM and TEM, respectively. Vickers hardness experiment were performed to investigate the mechanical properties of the $Al_2O_3$/Fe-Ni nanocomposite.

• 연구논문집
• /
• s.34
• /
• pp.139-146
• /
• 2004

In this study, effect of temperature and time on melt-out of 25wt% Al-alloyed ductile iron has been investigated. The oxidation tests were carried out in a tube furnace at $800^\circC$, $930^\circC$, and $1000^\circC$ for lh, 5h, 10h, 50h. The microstructure, microhardness, and $Al_2O_3$ layer of oxidation-treated 25wt% Al-alloyed ductile iron samples (10 x 10 x 10 mm) were investigated. Phase identification was performed by X-ray diffraction(XRD) and EDS. The oxidation-treated 25wt% Al-alloyed ductile iron samples at $930^\circC$ for lh, 5h, 10h and KS GCD 500 were used for melt-out test in an Al alloy melt. The melt-out test results showed that oxidation tested sample at $930^\circC$ for 5h which on the whole forms $2-3\mum$ $Al_2O_3$ layer showed lowest melt-out depth. It was observed showed that appropriate Al203 layer can affect melt-out behaviors.