• Journal of Korea Foundry Society
• /
• v.42 no.6
• /
• pp.337-346
• /
• 2022

In order to optimize the solution treatment conditions of Al-7Si-(0.3~0.5)Mg-(0~0.5)Cu alloys, a series of heat treatment experiments were conducted under various solution treatment times up to 7 hours at 545℃, followed by a microstructural analysis using optical microscopy, FE-SEM, and Brinell hardness measurements. Rapid coarsening of eutectic Si particles was observed in the alloys during the first 3 hours of solution treatment but the size of those Si particles did not change at longer solution treatment conditions. Meanwhile, the degree of spheroidisation of eutectic Si particles increased until the solution treatment time was increased up to 7 hours. Q-Al5Cu2Mg8Si6 andθ-Al2Cu were observed in as-cast Cu-containing Al alloys but the intermetallic compounds were dissolved completely after 3 hours of solution treatment at 545℃. Depending on the initial Mg composition of the Al alloys, π-Al8FeMg3Si either disappeared in the alloy with 0.3wt% of Mg content after 5 hours of solution treatment or remained in the alloy with 0.5wt% of Mg content after 7 hours of solution treatment time. Mg and Cu content in the primary-α phase of the Al alloys increased until the solution treatment time reached 5 hours, which was in accordance with the dissolution behavior of Mg or Cu-containing intermetallic compounds with respect to the solution treatment time. From the results of microstructural changes in the Al-7Si-Mg-Cu alloys during solution treatment, it was concluded that at least 5 hours of solution treatment at 545℃ is required to maximize the age hardening effect of the present Al alloys. The same optimal solution treatment conditions could also be derived from Brinell hardness values of the present Al-7Si-Mg-Cu alloys measured at different solution treatment conditions.

• Journal of Korea Foundry Society
• /
• v.6 no.2
• /
• pp.104-115
• /
• 1986

I A쪽과 II A쪽이 Al-Si 합금의 공정조직개량 처리에 효과적인 것은 잘 알려진 사실이나 Na(Sodium)과 Sr(Strontium)만 상업적으로 쓰여지고 있다. 그러나 휘발성과 산화하기 쉬운점때문에 Na 은 그 양을 정확하게 조절하기가 어렵고 특히 온도가 높은 경우 더욱 곤란하나 Sr 은 휘발성이나 산화성은 없으나 micro-또한 macro-porocity의 주 원인으로 보고 되고 있다. 희토류 금속 (예 : Cerium, Lanthanum,etc )도 개량처리 효과가 있다는 논문들(ref. 2, 3, 4, 5) 이 있고, 계속 연구되어 오고 있으나 그 세부사항과 효율성에 관해 정립된 바가 없다. 이런 연유로 Al-Si 합금의 생산을 위한 개량 처리제로서의 희토류 금속의 역할에 대해 구체적이고 세부적인 개량처리기구의 구명을 위해 이 연구가 이루어졌다. Al-Si 합금 356가 채택된 이유는 상업적 Al 주물의 생산을 감안해서 였다.

• Korean Journal of Materials Research
• /
• v.27 no.11
• /
• pp.603-608
• /
• 2017

$Si_3N_4$ is a ceramic material attracting attention in many fields because of its excellent abrasion resistance. In addition, Ti and TiAl alloys are metals used in a variety of high temperature environments, and have attracted much attention because of their high strength and high melting points. Therefore, study of the interface reaction between $Si_3N_4/Ti$ and $Si_3N_4/TiAl$ can be a useful practice to identify phase selection and diffusion control. In this study, $Si_3N_4/Ti_5Si_3+TiN/TiN/Ti$ diffusing pairs were formed in the $Si_3N_4/Ti$ interfacial reaction and $Si_3N_4/TiN(Al)/Ti_3Al/TiAl$ diffusion pathway was identified in the $Si_3N_4/TiAl$ interfacial reaction. The diffusion layers of the interface reactions were identified and, to investigate the kinetics of the diffusion layer, the integrated diffusion coefficients were estimated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2279-2286
• /
• 1992

A hypereutectic Aluminum-Silicon Alloy is widely used in the parts of autombile because of high-resistance and good strength. In this study, the cutting of a hypereutectic Al-Si alloy (A390) for extraction of Si particle was experimentally investigated. By proper selection of cutting tool materials and optimization of cutting conditions, economical machining of this alloy is achieved. The surface roughness relates closely with the feed rate and cutting speed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.78-79
• /
• 2015

PVD 공정에서 다성분으로 이루어진 나노복합 코팅을 형성하는 것은 원소들간의 합금화 문제로 인해 어렵다. 따라서 일반적으로 두 개 이상의 원소타겟 또는 멀티타겟을 이용한 PVD+PECVD 의 융합공정에 의해 제조된다. 하지만 멀티타겟을 사용한 공정은 공정의 복잡화가 뒤따르며 신뢰성이 떨어진다. 본 연구에서는 멀티타겟의 단점을 보완하기 위해 Ti-Al-X(Cr, Si, B, V) 단일 합금 타겟을 제작하여 나노복합 코팅을 형성하고자 하였다. 기계적 합금화법을 통해 합금분말을 제조하였으며, 방전플라즈마소결법으로 합금 타겟을 제작하였다. 제작된 타겟을 이용하여 스퍼터링 장치를 통해 박막을 형성 하였다. 그 결과 분말은 밀링 시간 20시간에서 정상상태에 도달하였으며, 더 이상 분말의 입자는 줄어들지 않았다. 이때 분말의 입자크기는 $5{\sim}6{\mu}m$ 이었으며 결정립의 크기는 16~20nm 이었다. 소결을 통해 99% 이상의 진밀도를 갖는 합금타겟을 제작하였으며, 이때 결정립의 크기는 매우 미세하였다. 박막의 경우 모두 30GPa 이상의 고경도 특성을 나타냈다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.6
• /
• pp.612-617
• /
• 2001

A nondestructive evaluation technique for detecting internal defects of an hot forged Al-Si alloy part is established in this study. Ultrasonic characteristics of various internal planar defects are investigated by experiments for establishing a reliable test procedure. The effect of the angle between ultrasonic energy propagation directions and planar defects on the ultrasonic signal configuration is evaluated in the pulse-echo technique. A characteristic of ultrasonic signal for the internal planar defect located near the edge is also evaluated. The applicability of the through-transmission technique is also discussed. Reliability of the presented approach is validated by the destructive testing for more than 500 specimens.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.8
• /
• pp.170-177
• /
• 1999

과공정 알루미늄 실리콘 합금 (Hypereutectic Al-Si Alloy, A390)은 내마멸성 및 우수한 강성에 의해서 자동차 부품에 많이 사용되고 있다. 본 연구에서는 초음파 진동 절삭에 의한 과공정 알루미늄 실리콘 합금의 가공성과 실리콘 석출의 실험적 연구를 수행 하였다. 최적 공구와 가공조건의 선정 실험을 통하여 보다 효과적인 초음파 진동 절삭을 수행하였으며, 과공정 알루미늄 실리콘 합금의 가공 표면거칠기와 실리콘 석출은 절삭속도와 절삭깊이와 밀접한 연관성을 갖고 있다.

• Journal of Korea Foundry Society
• /
• v.43 no.4
• /
• pp.203-209
• /
• 2023

• Journal of Welding and Joining
• /
• v.29 no.2
• /
• pp.88-93
• /
• 2011

This study produced hypereutectic Al-Si clad layer on 1050 Al alloy by a novel laser cladding method. Pure Si powder was mixed with organic binder to make fluid paste which could be screen-printed on the 1050 Al alloy plate. Pulsed Nd:YAG laser was irradiated on the Si paste layer to melt and alloy with Al substrate. Different laser power of 99 W, 179 W and 261 W, was used to see the difference of the microstructure, composition and hardness of the clad layers. When laser power of 179 W was used, the clad layer had overall Si content of 38wt% and composed of fine primary Si particles and fine eutectic phase. At laser power of 261 W, the clad layer had overall Si content of 24wt% and composed of mainly fine eutectic phase. Vickers hardness of HV176.7 and HV150.3 on the clad layer was obtained at laser power of 179 W and 261 W, respectively.

• Journal of Powder Materials
• /
• v.2 no.1
• /
• pp.36-43
• /
• 1995

Rapidly solidified and mechanically alloyed Al-Ti base alloys were prepared by gas atomization and attritor milling separately. The gas atomized and the mechanically alloyed powders were consolidated after preheating at $450^{\circ}C$, and then heat treated isochronally for 1 hour to observe the microstructures and to investigate the mechanical properties. Stable phases of precipitates in the Al-Ti-Si and the Al-Ti-Zr alloys were identified as DO22-$(Al,Si)_3Ti$ and $Do_{23}-Al_3(Ti, Zr)$ each. Among the alloys, the mechanically alloyed Al-l0Ti-2Si alloy showed superior thermal stability and mechanical properties at elevated temperature. The additions of third elements, such as Si and Zr, to Al-Ti alloys seemed to improve the mechnical properties remarkably by stabilizing the microstructure and the precipitate phases in the consolidated alloys.