• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.5
• /
• pp.295-303
• /
• 2012

Removal of total nitrogen (T-N) and total phosphorus (T-P) was evaluated in a DEPHANOX process by adding Al(III) to the separator to maintain T-P in the final effluent below 0.2 mg/L. pH in each reactor was maintained 7~8 after addition of Al(III) to the levels of 5, 10, 15 mg/L. The removal efficiency of COD and T-N decreased at higher Al(III) dose, but T-P removal efficiency increased from 76.28 to 84.02, 94.66% at Al(III) dose of 5, 10, 15 mg/L, respectively. T-P in effluent showed 0.17 mg/L at Al(III) dose of 15 mg/L. Minimum 15 mg/L of Al(III) was required to maitain T-P below 0.2 mg/L in the final effluent.

• Tribology and Lubricants
• /
• v.20 no.2
• /
• pp.97-101
• /
• 2004

This paper reports the studies on the wear-corrosion behavior of Al-Mg alloy in various pH environments. In various pH of sea water, corrosion and wear-corrosion loss of Al-Mg alloy were investigated. Also, the polarization test of Al-Mg alloy using potentiostat/galvanostat was carried out. And the rubbed surface of Al-Mg alloy using scanning electron micrographs after wear-corrosion test was examined in various pH values of sea water. The main results are as following : The polarization resistance of Al-Mg alloy in pH 4 solution is higer than that in pH 6.7 solution, and the corrosion current density in pH 4 is controlled than in pH 6.7 solution. The wear-corrosion loss of Al-Mg alloy with lowering pH becomes sensitive. As the oxide product of Al-Mg alloy appears granular structure and exholiation phenomenon, wear-corrosion loss of Al-Mg alloy increases.

• Korean Journal of Soil Science and Fertilizer
• /
• v.13 no.3
• /
• pp.93-97
• /
• 1981

Laboratory experiment was carried out to investigate the changes in the amount of inorganic phosphorus fractions of native and applied phosphorus and to compare the some analytical methods of soil phosphorus in volcanic ash. The rates of inorganic phosphorus to total-pP were varied with the kinds of soil in the ranges of 6.9 to 28.8% for Al-P, 24.1 to 26.9% for Fe-P, 7.4 to 11.9% for Ca-P and 0.7 to 8.0% for available phosphorus. The composition of inorganic phosphorus after incubation for 60 days was in the order of Al-P>Fe-P>Ca-P in Black soil, Fe-P>Al-P>Ca-P in Very dark brown soil, Fe-P>Ca-P>Al-P in Dark brown soil and Fe-P Al-P>Ca-P on Red yellow soil. The amounts of phosphorus extracted from soil varied with the methods for available phosphorus estimation. The magnitute of available P measured by Bray No. 2 method was the greatest. In relationship between inorganic phosphorus forms and available phophorus, Bray No. 2 method was closely related to Ca-P only and Olsen method correlated to Al-P, Fe-P, Ca-P and Total-P.

• Korean Journal of Environmental Agriculture
• /
• v.30 no.3
• /
• pp.229-233
• /
• 2011

BACKGROUND: Soil acidification, which is known to be one of the reasons of forest decline, is associated with decreases in exchangeable Ca and increases in Al concentration, leading to low Ca/Al ratio in soil solution. As tree rings are datable archives of environmental changes, Ca/Al ratios of annual growth ring may show decreasing pattern in accordance with the progress of soil acidification. This study was conducted to investigate Ca/Al pattern of Pinus densiflora tree ring in an attempt to test its usefulness as an indicator of historical soil acidification. METHODS AND RESULTS: Three P. densiflora tree disks were collected from P. densiflora forests in Jeonnam province, and soil samples (0-10, 10-20, and 20-30 cm in depth) were also collected from the tree locations. Soils were analyzed for pH and exchangeable Ca and Al concentrations, and Ca/Al was calculated. Annual growth rings formed between 1969 and 2007 were separated and analyzed for Ca/Al. Soil Ca/Al was positively (P<0.01) correlated with soil pH, suggesting that soil acidification decreased Ca while increasing Al availability, lowering Ca/Al in soil solution. The Ca/Al of tree rings also showed a decreasing pattern from 18.2 to 5.5 during the period, and this seemed to reflect historical acidification of the soils. CONCLUSION(s): The relationship between soil pH and Ca/Al and the decreasing pattern of Ca/Al of tree ring suggest that Ca/Al of tree ring needs to be considered as a proxy of the progress of soil acidification in P. densiflora forest in southern Korea.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.42-42
• /
• 2011

본 연구에서는 광학소자에 폭넓게 이용되는 AlGaP III-V족 화합물 반도체 중에서 한쪽 끝 이 종화합물인 AlP의 유전함수를 0.75~5.05 eV의 에너지 영역에서 타원편광분석법을 이용하여 분석하였다. AlP는 산소와 급격히 반응하기 때문에, 대기 중에서 물질 고유의 광특성이 유지되기 어려울 뿐만 아니라, 박막 위에 생성되는 산화막 때문에 순수한 AlP의 유전함수 측정이 불가능 하다. 본 연구에서는 물질의 유전함수에 미치는 산화 효과를 최소화하기 위하여 Molecular Beam Epitaxy로 성장한 $1.0{\mu}m$ 두께의 AlP 박막을 초고진공 상태의 chamber 안에서 타원편광분석기를 이용하여 실시간으로 측정하였다. 박막의 투명도에 의해 나타나는 간섭 pattern과 표면거칠기 효과로 인한 유전함수의 왜곡을 보정하기 위하여 변수화 모델이 이용되었으며 다층 변수화모델 계산을 통하여 순수한 AlP의 유전함수를 얻어낼 수 있었다. 본 연구에서 측정된 순수한 AlP의 유전함수는 타원편광분석기를 이용한 최초의 실험결과로서 이차미분을 이용한 전이점 (Critical Point) 분석결과 이론적인 electronic band structure에서 $E_1$, $E_1+_{{\Delta}_1}$, $E_2$에 해당하는 전이점들을 확인할 수 있었다.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.85-86
• /
• 2006

A theoretical model is applied to the analysis of thermomechanical properties of $Al-SiC_p$ FGMs in this study. Functionally graded $Al-SiC_p$ composites ($Al-SiC_p$ FGMs) consisted with 10 layers gradually changing volume fractions of Al and $SiC_p$ were fabricated using the pressureless infiltration technique. $Al-SiC_p$ FGMs plates of total thickness of 3mm, 5mm and 7mm with fairly uniform distribution and compositional gradient of $SiC_p$ reinforcement in the Al matrix throughout the thickness was successfully fabricated. The curvature of $Al-SiC_p$ FGM plates was measured to check the internal stress distribution predicted via a theoretical model for the analysis of thermo-mechanical deformation. The evolution of curvature and also internal stresses in response to temperature variations could be predicted for the different combinations of geometric thickness of FGM plates. Theoretical prediction of thermally induced stress distribution makes it possible to design FGM structures without any critical failure during the usage of them.

• Journal of the Korean Magnetics Society
• /
• v.25 no.6
• /
• pp.175-179
• /
• 2015

The half-metallicity and magnetism of the (001) surfaces of $(AlP)_1/(CrP)_1$ superlattice were investigated by means of FLAPW (Full-potential Liniarized Augmented Plane Wave) method. We considered four types of (001) surface termination, i.e., Al(S)-, Cr(S)-, P(S)Al(S-1)- and P(S)Cr(S-1)-term systems. We found that only Cr(S)-term system maintains the half-metallicity at the surface as only this system has the calculated magnetic moment of integer number of bohr magnetons. The magnetic moment of Cr(S) atom in the system was $3.02{\mu}_B$ which was increased from the bulk value by the effects of band narrowing and increased spin-splitting at the surface. The electronic density of states of the P(S) atom in the P(S)Al(S-1)-term showed very sharp surface states due to the broken $p_z$ bonds at the surface. We found there is still a strong p-d hybridization between the P(S) and Cr(S-1) layers in the P(S)Cr(S-1)-term which causes a considerable increase of magnetic moment of P(S) atom.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.68-72
• /
• 2008

AlGaInP high-brightness LEDs(HB-LEDs) have gained importance a variety of application operating in the red, orange, yellow and yellow-green wavelength. The light generated from inside LED chips should be emitted to the air through the surfaces of the chips. However, because of the differences between the semiconductor and air or epoxy's refractive index, some of the light was blocked so that caused lowering external quantum efficiency. In this study, nano-scale roughness on the top-GaP layer of AlGaInP epitaxial wafer was fabricated to improve' the brightness of AlGaInP LEDs. Nano-scale roughness was made by ICP dry etcher. Our AlGaInP LEDs with nano-scale roughness has higher brightness (about 28.5 %) than standard AlGaInP LEDs.

• Journal of Korean Society of Water and Wastewater
• /
• v.26 no.2
• /
• pp.229-236
• /
• 2012

The analysis of Al (III) hydrolysis species with PACls prepared by different basicity showed that mononmeric Al species were reduced while precipitate Al species were increased with an increase in basicity for PACls. In the case of the PACl with 13.6% basicity, monomeric Al species were 81%, polymeric Al (III) species 19%, precipitate Al (III) species was 0%, as showing the dominant monomeric Al species. The PACl with 13.6% basicity showed above 80% of turbidity removal efficiency without any restabilization. In addition, the PACl with 13.6% basicity showed higher organic removal expressed by $UV_{254}$ which was caused by lower coagulation pH. The PACl containing the higher amount of monomeric Al species was the most beneficial for T-P and $PO_{4}-P$ removal.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.6
• /
• pp.575-579
• /
• 2008

Al-doped p-type ZnO films were fabricated on n-Si (100) and homo-buffer layers in pure oxygen at $450^{\circ}C$ of by RF magnetron sputtering. Target was ZnO ceramic mixed with 2 wt% $Al_2O_3$. XRD spectra show that the Al-doped ZnO thin films have ZnO crystal structure and homo-buffer layers are beneficial to Al-doped ZnO films to grow along c-axis. Hall Effect experiments with Van der Pauw configuration show that p-type carrier concentrations are ranged from $1.66{\times}10^{16}$ to $4.04{\times}10^{18}\;cm^{-3}$, mobilities from 0.194 to $2.3\;cm^2V^{-1}s^{-1}$ and resistivities from 7.97 to $18.4\;{\Omega}cm$. p-type sample has density of $5.40\;cm^{-3}$ which is smaller than theoretically calculated value of $5.67\;cm^{-3}$. XPS spectra show that Ols has O-O and Zn-O structures and Al2p has only Al-O structure. P-ZnO:Al/n-ZnO:Al junctions were fabricated by magnetron sputtering. V-I curves show that the p-n junctions have rectifying characteristics.