• Journal of the Korean institute of surface engineering
• /
• v.52 no.5
• /
• pp.275-281
• /
• 2019

Anodization is widely used to enhance the properties of aluminum, such as hardness, electric resistance, abrasion resistance, corrosion resistance etc. But these properties can be enhanced with additional process. According to the partial crystallization of oxide layer with post heat treatment, enhanced hardness can be expected with partial crystallization. In this study, post heat treatments were applied to the anodized aluminum alloys of Al6061 to achieve the partial crystallization, and crystallizations were evaluated with the reduced breakdown voltages. Interestingly, remarkable enhanced hardness (21~29%), abrasion resistance (26~62%), and reduced breakdown voltage (24~44%) were observed for the sulfuric acid anodized samples when we annealed the anodized samples with 1hour post heat treatment at $360^{\circ}C$. For the Al5052 alloys, a lot of cracks were observed when we applied the post heat treatment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.30 no.5
• /
• pp.458-463
• /
• 2010

Since the acoustic nonlinearity is sensitive to the minute variation of material properties, the nonlinear ultrasonic technique(NUT) has been considered as a promising method to evaluate the material degradation or fatigue. However, there are certain limitations to apply the conventional NUT using the bulk wave to thin plates. In case of plates, the use of Lamb wave can be considered, however, the propagation characteristics of Lamb wave are completely different with the bulk wave, and thus the separate study for the nonlinearity of Lamb wave is required. For this work, this paper analyzed first the conditions of mode pair suitable for the practical application as well as for the cumulative propagation of quadratic harmonic frequency and summarized the result in for conditions; (1) phase matching, (2) non-zero power flux, (3) group velocity matching, and (4) non-zero out-of-plane displacement. Experimental results in aluminum plates showed that the amplitude of the secondary Lamb wave and nonlinear parameter growed up with increasing propagation distance at the mode pair satisfying the above all conditions and that the ration of nonlinear parameters measured in Al6061-T6 and Al1100-H15 was closed to the ratio of the absolute nonlinear parameters.

• Journal of the Korean Ceramic Society
• /
• v.47 no.3
• /
• pp.256-261
• /
• 2010

Physical properties of Plasma electrolytic oxidized 8 different types of Al alloys, A-1100, A-2024, A-5052, A-6061, A-6063, A-7075, ACD-7B and ACD-12 were investigated. The electrolyte for PEO was $Na_2SiO_3$ solutions with NaOH and some alkali earthen metal salts. Porous layer near the surface of PEO coating was not found, and surface roughness Ra50 was below 2.5 ${\mu}m$. Surface roughness was affected by growth rate of plasma electrolytic oxidized layer, not by Si content in Al alloy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.290-290
• /
• 2013

플라즈마 전해산화(Plasma Electrolytic Oxidation)란 저 농도의 알칼리 전해액을 매개로, 고전압을 가해 미세 플라즈마 방전을 유도하여 Al, Mg, Ti 등의 금속표면을 산화시켜 고내식성, 초경합금 수준의 내마모성, 탁월한 절연성과 고경도성을 가지는 산화막을 형성시키는 기술로 전자, 자동차, 의료, 섬유, 해양, 석유화학 산업에 이르기까지 광범위한 분야에 적용되어 우수한 물성을 확보할 수 있는 차세대의 표면처리 기술이다. 본 연구에서는 6061 알루미늄 합금을 이용하여 다양한 전해액 조건에서 플라즈마 전해산화 공정으로 Al2O3 산화막을 형성시켰다. 산화막의 조성 및 미세구조는 XRD와 FE-SEM, EDS를 이용하여 분석하였다. 형성된 산화막은 회색에서 밝은 회색으로 시편 전면에 고르게 나타났다. 전해액 조성을 바꾸어줌에 따라 각기 다른 표면 특성을 가지는 산화막을 얻을 수 있었고, 그에 따른 물성 변화를 분석하였다. 특히 Si 이온 농도를 조절함으로써 피막 성장인자와 표면 미세구조를 제어할 수 있었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.298-298
• /
• 2013

플라즈마 전해산화기술은 알루미늄 소재에 대해 기존의 양극 산화막, 전해 경질크롬 도금 및 플라즈마 세라믹 용사기술 등에 의해 구현할 수 없는 고기능성을 부여하여 월등히 우수한 경도, 내부식, 내마모, 전기절연, 열저항, 피로강도 등을 얻을 수 있는 획기적인 기술이다. 또한 최근 환경에 대한 관심이 점차 높아지면서 친환경적 공정과정과 경금속 소재의 제품에 내구성을 향상시킬 필요성이 높아지고 있다. 이러한 요구에 부합하는 플라즈마 전해 산화기술은 알칼리 수용액 중에서 Al, Ti, Mg 등의 표면에 산화 피막을 형성시키는 기술로써 기존의 양극산화(Anodizing)을 대체 할 수 있다. 본 연구에서는 Al6061을 이용하여 플라즈마 전해산화 공정에 사용되는 전해액의 종류 및 농도, 시간의 변화에 따른 산화 피막의 변화를 내전압 측정 및 FE-SEM, EDS, XRD를 통해 분석하였다. 전해액에 sodium hexameta phosphate과 potassium phosphate를 이용하여 phosphate 종류의 변화에 따른 피막 특성의 변화를 연구하였다. 그로인해 phosphate의 종류 및 농도, 시간 변화를 이용하여 플라즈마 전해산화공정의 산화 피막 물성 제어를 할 수 있다.

• Journal of the Korean institute of surface engineering
• /
• v.52 no.4
• /
• pp.203-210
• /
• 2019

In this work, anodizing behavior of 6xxx series aluminum alloys was studied under constant current density and constant voltage conditions in 20% sulfuric acid solution by V-t curves, I-t curves, thickness measurement, observations of surface appearance and cross-sectional observation of anodizing films. The film growth rate of the anodizing films on Al6063, Al6061 and Al6082 obtained at 20 V were $0.63{\mu}m/min$. $0.46{\mu}m/min$ and $0.38{\mu}m/min$, respectively. Time to the initiation of imperfections at the oxide/substrate interface under constant current condition was shortened and colors of anodizing films became darker with the amount of alloying elements in 6xxx series aluminum alloys. Based upon the experimental results obtained in this work, it is concluded that maximum anodizing film thickness without interfacial defects is reduced with increasing amount of alloying elements and brighter anodizing films can be obtained by decreasing amount of alloying elements in the aluminum alloys.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.4
• /
• pp.127-134
• /
• 2021

In this study, the adhesive fracturing characteristics of a DCB specimen due to single and heterogeneous bonding materials under tearing load was investigated. The experiments were conducted to examine the fracturing properties of the adhesive DCB specimen. As an experimental condition, a forced displacement of 3mm/min was applied to one side while the other side was fixed. As a result of the experiment, it was found that the AL6061-T6 material was superior to the CFRP material in terms of maximum stress, specific strength, and energy release rate when compared to the adhesive fracturing property of a single material. We tested CFRP-AL, a heterogeneous bonding material, and compared its experimental results to the results from the single materials. Based on these results, CFRP-AL with a heterogeneous bonding material was observed to have the superior structural safety compared to single materials for the mode III fracture type.

• Journal of Powder Materials
• /
• v.30 no.3
• /
• pp.255-261
• /
• 2023

Aluminum alloys are widely utilized in diverse industries, such as automobiles, aerospace, and architecture, owing to their high specific strength and resistance to oxidation. However, to meet the increasing demands of the industry, it is necessary to design new aluminum alloys with excellent properties. Thus, a new method is required to efficiently test additively manufactured aluminum alloys with various compositions within a short period during the alloy design process. In this study, a combinatory approach using a direct energy deposition system for metal 3D printing process with a dual feeder was employed. Two types of aluminum alloy powders, namely Al6061 and Al-12Cu, were utilized for the combinatory test conducted through 3D printing. Twelve types of Al-Si-Cu-Mg alloys were manufactured during this combinatory test, and the relationship between their microstructures and properties was investigated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2498-2508
• /
• 1993

$Al/SiC/Al_{2}O_{3}$ hybrid composites are fabricated by squeeze infiltration method. From the misconstructive of $Al/SiC/Al_{2}O_{3}$ hybrid composites fabricated by squeeze infiltration method, uniform distribution of reinforcements and good bondings are found. Hardness value of $Al/SiC/Al_{2}O_{3}$ hybrid composites increases linearly with the volume fraction of reinforcement because SiC whisker and $Al_{2}$O$_{3}$ fiber have an outstanding hardness. Optimal aging conditions are obtained by examining the hardness of $Al/SiC/Al_{2}O_{3}$ hybrid composites with different aging time. Tensile properties such as Young's modulus and ultimate tensile strength are improved up to 30% and 40% by the addition of reinforcements, respectively. Failure mode of $Al/SiC/Al_{2}O_{3}$ hybrid composites is ductile on microstructural level. Through the abrasive wear test and wear surface analysis, wear behaviour and mechanism of 6061 aluminum and $Al/SiC/Al_{2}O_{3}$ hybrid composites are characterized under various testing conditions. The addition of SiC whisker to $Al/SiC/Al_{2}O_{3}$ composites gives rise to improvement of the wear resistance. The wear resistance of $Al/SiC/Al_{2}O_{3}$ hybrid composites is superior to that of Al/SiC composites. The wear mechanism of aluminum alloy is mainly abrasive wear at low speed range and adhesive and melt wear at high speed range. In contrast, that of $Al/SiC/Al_{2}O_{3}$ hybrid composites is abrasive wear at all speed range, but severe wear when counter material is stainless steel. As the testing temperature increases, wear loss of aluminum alloy decreases because the matrix is getting more ductile, but that of $Al/SiC/Al_{2}O_{3}$ hybrid composites is hardly varied. Oil lubricant is more effective to reduce the wear loss of aluminum alloy and $Al/SiC/Al_{2}O_{3}$ hybrid composites at high speed range.

• Journal of the Korean Ceramic Society
• /
• v.49 no.3
• /
• pp.247-252
• /
• 2012

Crystal structure and chemical compositions of Plasma electrolytic oxidized layer of A-1100, A-2024, A-5052, A-6061, A-6063, A-7075, ACD-7B and ACD-12 were investigated. The electrolyte for plasma electrolytic oxidation was mixture of distilled water, $Na_2P_2O_7$, Cu, Cr metal salts and KOH. ${\eta}$-Alumina, as well as ${\alpha}$-alumina, was main crystal phase. Another crystals such as $(Al_{0.948}Cr_{0.052})_2O_3$ and $(Al_{0.9}Cr_{0.1})_2O_3$ were also formed in the oxide layer. It was thought that the effect of electrolyte compositions on the physical properties and crystal system of PEO layers was greater than the effect of Al alloy composition variation.