• Korean Journal of Food Science and Technology
• /
• v.27 no.6
• /
• pp.915-920
• /
• 1995

This study was performed to investigate the effect of aluminum compound on the aluminum contents and histological change in brain tissue of rats. Seventy five male Sprague-Dawley strains were divided into five groups consisting of the control, 250 ppm $AlCl_3$ group, 500 ppm $AlCl_3$ group, 250 ppm $Al_2(SO_4)_3$ group, 500 ppm $Al_2(SO_4)_3$ group and kept on the diet for 2 weeks. The weight gain was increased by administration of $AlCl_3$ but decreased by administration of $Al_2(SO_4)_3$ as compared to control group. The aluminum contents in brain tissue of each group; 250 ppm $AlCl_3$ group, 500 ppm $AlCl_3$ group, 250 ppm $Al_2(SO_4)_3$ group and 500 ppm $Al_2(SO_4)_3$ group were 64.63, 102.21, 132.64 and 180.41 ppm, respectively. Aluminum accumulation in brain tissue was higher with administration of $Al_2(SO_4)_3$ than with administration of $AlCl_3$. In $AlCl_3$ administration group, multiple small intracytoplasmic granules and microvacuole were seen in large pyramidal cells of cortex and granulovacuolar degeneration. In $Al_2(SO_4)_3$ administration group revealed pollagis pallor, cellular pyknosis, microcavitation resulted from edema in deeper cortical layers were observed. Blue-pigmentation which represents the accumulation of aluminum was noted In granulovacuolar degeneration site in $Al_2(SO_4)_3$ administration group.

• Journal of the Korean Ceramic Society
• /
• v.19 no.3
• /
• pp.179-186
• /
• 1982

This research is to aim at the study of sintering mechanism through the observation of microstructure by scanning electron microscopy, after the mixture of 30wt% $Al_2O_3$ (White Alundum) powder is fired in air at the temperature range of 1350~150$0^{\circ}C$ in order to sinter $Al_2O_3$-Al through the oxidation of Al powder. The results obtained in this experiment are as follows: 1. While the compressive strength of $Al_2O_3$(WA) body fired at $1450^{\circ}C$ for 5hrs in air is 150kg/$\textrm{cm}^2$, that of Al-$Al_2O_3$ body fired at 135$0^{\circ}C$, $1400^{\circ}C$ for 5hrs in air is 1100kg/$\textrm{cm}^2$, 1600kg/$\textrm{cm}^2$ respectively, and the higher the firing temperature, the more the compressive strength increases. These results from the sintering effect between $Al_2O_3$(WA) grains and surrounding Al-oxidation layer. 2. While the compressive strength of Al2O3(WA) body fired at 150$0^{\circ}C$ for 5hrs in air is 250kg/$\textrm{cm}^2$, the compressive strength of Al-$Al_2O_3$body fired under the same condition is 2050kg/$\textrm{cm}^2$ and water absorption 9.0%, porosity 23.3%, bulk density 2.60gr/$cm^3$. It is assumed that these results come from not only the grain growth of oxidized Al grains but also the increase of bonding strength between $Al_2O_3$(WA) grains.

• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.733-739
• /
• 2001

In Al-25Nb binary system, it was observed only formation of $D0_{22}$ $Al_3Nb$ intermetallic compound after 5hr milling but it was not observed formation of meta stable phase like L1$_2$ phase. In this state, $D0_{22}$ $Al_3Nb$ fabricated had nano sized grain of approximately 20nm. Ternary systems, transition metals such as Cr, Cu, Fe, Mn were added 6~12at.% as substitution of Al, showed formation of $D0_{22}$ $Al_3Nb$ like Al-25Nb binary system. In Al- l2Cu-25Nb system, it was observed that broad XRD pattern like amorphization of Al and not observed formation of $D0_{22}$ $Al_3Nb$ after 5hr milling. But there was mixed phase of a lot of amorphous Al and little $D0_{22}$ $Al_3Nb$ through TEM. In the states of unalloyed, 5~7hr milling time, those showed exothermic reaction at 35$0^{\circ}C$, which was formation of $D0_{22}$ $Al_3Nb$ like Al-25Nb binary system. With increasing milling time to 10hr, $D0_{22}$ $Al_3Nb$ was transformed to mixed phase of amorphous and nanocryatlline, having approximately 10nm grain but the meta stable $Al_3Nb$ was not fabricated by adding transition metals.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.483-490
• /
• 1997

Al2O3/metal composites were fabricated by oxidation and reaction of molten Al-alloy into two types of commercial Al2O3-SiO2 fibrous insulation board. The growth rate, composition and microstructure of these materials were described. An AlZnMg(7075) alloy was selected as a parent alloy. Mixed polycrystalline fiber and glass phase fiber were used as a filler. The growth surface of an alloy was covered with and without SiO2. SiO2 powder was employed as a surface dopant to aid initial oxidation of Al-alloy. Al-alloy, SiO2, fiber block and growth inhibitor CaSiO3 were packed sequentially in a alumina crucible and oxidized in air at temperature range 90$0^{\circ}C$ to 120$0^{\circ}C$. The growth rate of composite layer was calculated by measuring the mass increasement(g) per unit surface($\textrm{cm}^2$). XRD and optical microscope were used to investigate the composition and phase of composites. The composite grown at 120$0^{\circ}C$ and with SiO2 dopant showed rapid growth rate. The growth behavior differed a little depending on the types of fiber used. The composites consist of $\alpha$-Al2O3, Al, Si and pore. The composite grown at 100$0^{\circ}C$ exhibited better microstructure compared to that grown at 120$0^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.591-600
• /
• 1997

Al2O3/Al composites were produced by displacement reaction method, which was carried out by immersing the sintered silica preform, which was prepared from fused silica powder, in molten aluminum. Because the molten aluminum did not penetrate into the silica preform with higher than 20% of porosity when the displacement reaction was accomplished at 100$0^{\circ}C$ for 10 hours in air atmosphere, the optimum range of sintering temperature of silica preform was from 135$0^{\circ}C$ to 140$0^{\circ}C$. The microstructure of this Al2O3/Al composites showed three-dimentionally co-continuous alumina, which provides wear resistance and high stiffness, and aluminium which acts as a toughnening phase. The grain size of the alumina in composites did not change with the particle size of the silica preform. The exact shape of the preform was retained and a net-shaped composite was produced. The representative Al2O3/Al composite prepared in this study showed 3.30mg/㎤ of bulk density, 350-430 MPa of flexural strength, 7.0 MPa.m1/2 of fracture toughness, and good machinability.

• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.42-48
• /
• 1999

Three mixtures of elemental powders of Al-25at.%Ti, 48at.%Ti and 70at.%Ti were offered to ball milling process for the formation of intermetallic compounds of $Al_3Ti$, AlTi and $Ti_3Al$. Ballmilling or attrition process were carried out at the condition of rotaing speed of 110 or 350 rpm at $10^{-3}$ torr vacuum or argon atmospheres. $Al_3Ti$phases were fully obtained by heat treatment for 1 hors at $600^{\circ}C$ with Al-25at.%Ti composition mixtures milled by 100 hours. The amorphous phase was completely formed at the composition of Al-48at.%Ti mixed powders by milling 100hours at the 50 to 1 weight ratio of ball to powder, and AlTi compounds were obtained by heat treament. In the case of Al-70at%Ti mixed powders milled for 100 hours, $Ti_3Al$ and $Al_3Ti$intermetallic compounds were formed by heat treatment for 1 hour at $600^{\circ}C$. By attrition milling of 350rpm for 10 hours, $Ti_3Al$ phase was formed completley after heat treatment for 1 hour at $600^{\circ}C$.

• Journal of Powder Materials
• /
• v.4 no.3
• /
• pp.205-213
• /
• 1997

Mechanical alloying of $Ni_3Al$ and $Y_2O_3$ added ODS $Ni_3Al$ from elemental powders was investigated by the X-ray diffraction, differential scanning calorimeter, transmission electron microscopy and optical microscopy. The steady states of $Ni_3Al$ and ODS $Ni_3Al$ powders were reached after mechanical alloying with the condition of the ball-to-powder input ratio of 20:1 for 20 hours and 10 hours, respectively. The addition of nano-sized $Y_2O_3$ particles enhanced cold working and fracture, and subsequently accelerated MA of $Ni_3Al$ powders. DSC results of MAed $Ni_3Al$ powders showed four exothermic peaks at 14$0^{\circ}C$, 234$^{\circ}C$, 337$^{\circ}C$ and 385$^{\circ}C$. From the high temperature X-ray diffraction analysis, it was concluded that the peaks were resulted from the recovery solution of unalloyed Al in Ni, the formation of intermediate phase NiAl, and $LI_2$ ordering of MAed $Ni_3Al$ powders.

• Journal of Korea Foundry Society
• /
• v.33 no.3
• /
• pp.103-112
• /
• 2013

Effect of Fe and Mn contents on the tensile properties of Al-4 wt%Mg-0.9 wt%Si alloy system has been studied. Common phases of Al-4 wt%Mg-0.9 wt%Si alloy system were ${\alpha}$-Al, $Mg_2Si$, ${\alpha}-Al_{12}(Fe,Mn)_3Si$ and ${\beta}-Al_5FeSi$. As Fe content of Al-4 wt%Mg-0.9 wt%Si alloy system increased from 0.15 wt% to above 0.3 wt%, ${\beta}-Al_5FeSi$ compound appeared. When Mn content of the alloy increased from 0.3 wt% to 0.5 wt%, morphology of plate shaped ${\beta}-Al_5FeSi$ compound changed to chinese script ${\alpha}-Al_{12}(Fe,Mn)_3Si$. As Fe content of Al-4 wt%Mg-0.9 wt%Si-0.3 wt%Mn alloy increased from 0.15 wt% to 0.4 wt%, tensile strength of the as-cast alloy decreased from 191 MPa to 183 MPa and, elongation of the alloy also decreased from 8.0% to 6.2%. Decrease of these properties can be explained as the formation of plate shape, ${\beta}-Al_5FeSi$ phase with low Mn/Fe ratio of the alloy. However, when Mn content of Al-4 wt%Mg-0.9 wt%Si-0.3 wt%Fe alloy increased from 0.3 wt% to 0.5 wt%, tensile strength of as-cast alloy increased from 181 MPa to 194 MPa and, elongation of the alloy increased from 6.8% to 7.0%. These improvements attribute to the morphology change from ${\beta}-Al_5FeSi$ phase to chinese script, ${\alpha}-Al_{15}(Fe,Mn)_3Si_2$ phase shape-modified from with high Mn/Fe ratio of the alloy.

• Clean Technology
• /
• v.20 no.1
• /
• pp.51-56
• /
• 2014

In this study, PSf-$Al(OH)_3$ beads were prepared by immobilizating aluminum hydroxide $Al(OH)_3$ with polysulfone (PSf). The removal experiments of the fluoride ions by PSf-$Al(OH)_3$ beads were conducted batchwise and the parameters such as pH, initial fluoride concentration, and coexisting ions were investigated. The maximum removal capacity obtained from Langmuir isotherm was 52.4 mg/g and the optimum pH region of fluoride ions was in the range of 4 to 10. The removal process of fluoride ions by PSf-$Al(OH)_3$ beads was found to be controlled by both external mass transfer at the earlier stage followed by internal diffusion at the later stage. The presence of coexisting anions such as $HCO_3{^-}$, $SO{_4}^{2-}$, $NO_3{^-}$, and $Cl^-$ had a negative effect on removal of fluoride ions by PSf-$Al(OH)_3$ beads.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.230-236
• /
• 2021

Ionic conduction mechanism of Mg-Al layered double hydroxides (LDHs) intercalated with CO₃^2- (Mg-Al CO₃^2- LDH) was studied. The electromotive force for the water vapor concentration cell using Mg-Al CO₃^2- LDH as electrolyte showed water vapor partial pressure dependence and obeyed the Nernst equation, indicating that the hydroxide ion transport number of Mg-Al CO₃^2- LDH is almost unity. The ionic conductivity of Mg(OH)₂, MgCO₃ and Al₂(CO₃)₃ was also examined. Only Al₂(CO₃)₃ showed high hydroxide ion conductivity of the order of 10^-4 S cm^-1 under 80% relative humidity, suggesting that Al₂(CO₃)₃ is an ion conducting material and related to the generation of carrier by interaction with water. To discuss the ionic conduction mechanism, Mg-Al CO₃^2- LDH having deuterium water as interlayer water (Mg-Al CO₃^2- LDH(D₂O)) was prepared. After the adsorbed water molecules on the surface of Mg-Al CO₃^2- LDH(D₂O) were removed by drying, DC polarization test for dried Mg-Al CO₃^2- LDH(D₂O) was examined. The absorbance attributed to O-D-stretching band for Mg-Al CO₃^2- LDH(D₂O) powder at around the positively charged electrode is larger than that before polarization, indicating that the interlayer in Mg-Al CO₃^2- LDH is a hydroxide ion conduction channel.