• Aerospace Engineering and Technology
• /
• v.10 no.2
• /
• pp.146-153
• /
• 2011

Some methods of calculation of test load value from design load data were investigated which will be applied at strap installed full-scale airframe of composite aircraft. These methods were applied to left wing of KC-100 composite aircraft and the calculated test load values were compared with each others. Generally since test load values are differently calculated according to each aircraft type and position of straps, all calculation methods mentioned at this study need to be applied and compared to each aircraft. Finally the most appropriate method needs to be selected.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.6
• /
• pp.443-453
• /
• 2020

This study using the active vibration control technique attempts to alleviate numerically the airframe vibration of a UH-60A helicopter. The AVCS(Active Vibration Control System) is applied to reduce the 4/rev vibration responses at the specified locations of the UH-60A airframe. The 4/rev hub vibratory loads of the UH-60A rotor is predicted using the nonlinear flexible dynamics analysis code, DYMORE II. Various tools such as NDARC, MSC.NASTRAN, and MATLAB Simulink are used for the AVCS simulation with five CRFGs and seven accelerometers. At a flight speed of 158knots, the predicted 4/rev hub vibratory loads of UH-60A rotor excite the airframe, and then the 4/rev vibration responses at the specified airframe positions such as the pilot seat, rotor-fuselage joint, mid-cabin, and aft-cabin are calculated without and with AVCS. The 4/rev vibration responses at all the locations and directions are reduced by from 25.14 to 96.05% when AVCS is used, as compared to the baseline results without AVCS.

• Polymer Science and Technology
• /
• v.4 no.5
• /
• pp.358-364
• /
• 1993

• Journal of Aerospace System Engineering
• /
• v.9 no.2
• /
• pp.19-24
• /
• 2015

Export basic trainer was designed to add armed configuration required by customer. Design configuration of main wing was changed to satisfy changed internal load caused by armed configuration. It was verified that design changed main wing airframe of export basic trainer satisfy the requirement through the structural detail analysis, structural ground test and flight test. This paper presents the durability test procensure and test result for the main wing of export basic trainer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.340-346
• /
• 2013

This paper describes a helicopter vibration induced by main rotor in forward flight. The hub loads in the fixed frame, which are dominant source of helicopter vibration, are obtained by multi-blade summation of rotating blades loadings. The components of 3/rev, 4/rev, and 5/rev blades loadings are transmitted by blades to 4/rev hub loads in the fixed frame. The vertical vibrations of helicopter at pilot seat and copilot seat are calculated through rigid body transfer functions considering airframe to be rigid body. The blades are assumed to be elastic and undergo the flap, lag, and torsion motion and free wake aerodynamic model is used to calculate the precise blade loadings in the analysis. The 4/rev vertical vibration responses are analyzed from rotating blade loadings and fixed hub loadings.

• Journal of Aerospace System Engineering
• /
• v.5 no.1
• /
• pp.17-23
• /
• 2011

Since the time, cost and lack of regulatory information and guidance, one of the largest regulatory obstacles for an airframe manufacturer of polymer based advanced composite materials in certified aircraft applications, is to generate design allowables that will satisfy Airworthiness Regulations. In the past two decades, the design allowables used in military aircraft had been generated and applied in Korea, however the qualification of composite materials used in certifying airframe structure was not accomplished for design and demonstration of compliance to applicable airworthiness regulation. It is the intend of this paper that provide the basis of composite material qualification for small aircraft certification to the airworthiness regulation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.2
• /
• pp.47-52
• /
• 2007

Missile staging and airframe separation simulation were performed by using a numerical technique for simulating the dynamics of multiple moving bodies. A 6DOF model is fully integrated into the CFD solution procedure to determine the body dynamics. Chimera grid technique offered efficient CFD simulation of multiple moving bodies. Through this simulation the safety of deployed staging and airframe separation mechanism was verified.

• Korean Journal of Materials Research
• /
• v.25 no.10
• /
• pp.516-522
• /
• 2015

Aging aircraft structures are inevitably exposed to environment for a long time facing many potential problems, including corrosion and wide spread fatigue damage, which in turn cause the degradation of flight safety. In this study, the environmental surface damages on aging aircraft structures induced during service were quantitatively analyzed. Additionally, S-N fatigue tests were performed with center hole specimens extracted from aging aircraft structures. From the results of quantitative analyses of the surface damages and fatigue tests, it is concluded that corrosion pits initiated during service reduce the fatigue life significantly. Finally, using the fracture mechanics and the EIFS (equivalent initial flaw size) concepts, the remaining fatigue life was predicted based on actual fatigue test results.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.32 no.10
• /
• pp.367-375
• /
• 1983

An extended Kalman filter (EKF) algorithm for estimating aerodynamic parameters from missile flight data is evaluated using simulated test data. The algorithm includes a general purpose 6-DOF missile airframe suitable for representing a variety of missile configurations. The EKF is demonstrated to be well suited as a postflight analysis tool for extracting large numbers of airframe parameters from flight test measurements. A structure identification algorithm is evaluated using synthetic measurement data. This algorithm used in conjunction with the parameter identification algorithm, can select that model from a family of candidate models which most likely produced the synthetic measurement data.

• Advances in aircraft and spacecraft science
• /
• v.8 no.4
• /
• pp.331-344
• /
• 2021

Airframe internal and external specifications are the product of intensive intellectual efforts and technological breakthroughs distinguishing each aircraft manufacturer. Therefore, geometrical information characterizing aircraft primary aerodynamic surfaces remain classified. When attempting to model real aircraft, many members of the aeronautical community depend on their personal expertise and generic design principles to bypass the confidentiality obstacles and sketch real aircraft airfoils, which therefore vary for the same aircraft due to the different designers' initial assumptions. This paper presents a photogrammetric shape prediction method for deriving geometrical properties of real aircraft airframe by utilizing their publicly accessible static and dynamic visual content. The method is based on extracting the visually distinguishable curves at the fairing regions between aerodynamic surfaces and fuselage. Two case studies on B-29 and B-737 are presented showing how to approximate the sectional coordinates of their wing inboard airfoils and proving the good agreement between the geometrical and aerodynamic properties of the replicated airfoils to their original versions. Therefore, the paper provides a systematic reverse engineering approach that will enhance aircraft conceptual design and flight performance optimization studies.