• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.10
• /
• pp.888-895
• /
• 2015

This paper shows an approximate equation which calculates a flapping angle of blade for verification of KUH safety area. The flapping behavior of blade must be reviewed in an aspect of safety because of a collision possibility with airframe. However, it is difficult to measure an exact flapping angle during flight. A prediction equation of a coning angle is derived from aeromechanics and that of a dynamic flapping angle is derived from analysis results in development phase, respectively. Following, the equations are verified by comparison the flapping angle through an aircraft simulation test to a calculation. Finally, the safety area, which was established in development phase, is verified by calculating a flapping angle during the flight which is required by the terms of safety based on AC29 and FAR29.

• Journal of Biosystems Engineering
• /
• v.37 no.6
• /
• pp.342-351
• /
• 2012

Purpose: Aerial spraying with an agricultural unmanned helicopter became a new paradigm in the agricultural practice. Laterally tilting behavior of a conventional agricultural helicopter, resulting in the biased down-wash and uneven spray deposit is a physically intrinsic phenomenon while hovering and cruise flights. Authors studied and developed a roll-balanced agricultural helicopter with a raised pylon tail rotor system. In this study, the attitude of the roll-balanced helicopter was determined using the Kalman filter algorithm, and the quality of roll balancing of a bare-airframe helicopter was evaluated. Methods: Instantaneous attitudes were estimated using the advantage of gyroscope, followed by the long term correction and prediction using accelerometer data for the advantage of convergence. The attitudes of the fuselage were calculated by applying the Kalman filter algorithm. The spraying maneuver of the helicopter was performed at a field of 50 m long, and the attitude data were acquired and evaluated. Results: The determination of attitude using the inertial measurement unit(IMU) and Kalman filter was reliable and practical. The intrinsic attitude of the developed helicopter was stable and roll-balanced. The deviation of roll angle was ${\pm}6.3^{\circ}$ with an average of $0^{\circ}$, referring to roll-balanced. Conclusions: Handling quality of the roll attitude determined to be steadily balanced. The balancing behavior of the developed helicopter would result in an even spray pattern during aerial application.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.56-60
• /
• 2017

In hypersonic aircraft, increase of aerodynamic heat and engine heat leads heat loads in airframe. It could lead structural change of aircraft's component and malfunctioning. Endothermic fuels are liquid hydrocarbon fuels which are able to absorb the heat load by undergoing endothermic reactions. In this study, exo-tetrahydrodicyclopentadiene was selected as a model endothermic fuel and experiments were investigated in endothermic fuel cooling system with zeolite catalyst. Three shapes of catalysts have been manufactured and endothermic characteristics were recovered. Bineded catalyst showed higher heat absorption and conversion than other two zeolite catalysts. In product distribution, binded catalyst showed higher aromatics composition.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2013

In order to increase endurance flight efficiency of long endurance electric powered UAV with solar cell, the light weight airframe design techniques are important. In this paper, the design of the main wing of electric powered UAV manufactured using Mylar film and fiber reinforced composite was conducted in order to achieve weight reduction and structural integrity of the structure. The shape of spar and size were determined using beam theory analysis. The finite element analysis of the wing was performed under various load condition derived from flight environment of EAV-2H. Finally, the static strength test of the main wing was conducted to verify structural integrity. It was found that the developed main wing weigh less than 42% than the previous EAV-2 and the main wing passed static strength test under ultimate load.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.699-702
• /
• 2004

In this study, the affect of mounting axisymmetrical supersonic inlet to airfoil, which has 65 degree swept angle was numerically investigated. The parameter for this calculation are tree stream Mach number M=2.0 and 2.5, the distance between inlet spike and airfoil lower surface $L_{sw}$/$R_{cowl}$ = 1.21-1.54 and angle of attack to the airfoil 0-4. The mass capture ratio improved 3points in M=2.0 condition and 1points in M=2.5 while the mass capture ratio without airfoil surface was 57% and 71 % for each case. These are the result from increase of density and change of velocity deflection by the shock wave structure formed between inlet and airfoil surface. On the other hand, the distortion of Mach number at cowl lip plane increased by 13% in M=2.0, 3% in M=2.5 condition. The effects of the angle attack on the mass capture ratio is greater than that of the shock wave interaction between inlet and cowl, but the effects to the distortion is smaller in the range of this calculation condition. In the condition of M=2.0 with 4 degrees of angle of attack, inlet distortion of Mach number is mainly caused by the affects of the shock wave interaction between inlet and airfoil surface, while the largest angle of the velocity vector in the radial direction at cowl lip plane is caused by the affect of angle of attack. This large velocity vector made the flow inside the cowl subsonic and caused spillage, which interfere with the boundary layer of airfoil surface.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.734-741
• /
• 2004

Boundary layer ingestion in airframe-integrated scramjet engines causes engine stall (“engine un start” hereafter) and restricts engine performance. To improve the unstart characteristics in engines, boundary layer bleed and a two-staged injection of fuel were examined in Mach 4 and Mach 6 engine tests. A boundary layer bleed system consisting of a porous plate, an air coolers, a metering orifice and an ON/OFF valve, was designed for each of the engines. First, a method to determine bleed rate requirements was developed. Porous plates were designed to suck air out of the Mach 4 engine at a rate of 200 g/s and out of the Mach 6 engine at a rate of 30 g/s. Air coolers were then optimized based on the bleed airflow rates. The exhaust air temperature could be cooled below 600 K in the porous plates and the compact air coolers. The Mach 4 engine tests showed that a small bleed rate of 3% doubled the engine operating range and thrust. With the assistance of two-staged fuel injection of H2, the engine operating range was extended to Ф0.95 and the maximum thrust was tripled to 2560 N. The Mach 6 tests showed that a bleed of 30 g/s (0.6% of captured air in the engine) extended the start limit from Ф0.48 to Ф1 to deliver a maximum thrust of 2460 N.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.18 no.5
• /
• pp.95-100
• /
• 2014

In hypersonic aircraft, increase of aerodynamic heat and engine heat leads heat loads in airframe. It could lead structural change of aircraft's component and malfunctioning. Endothermic fuels are liquid hydrocarbon fuels which are able to absorb the heat load by undergoing endothermic reactions. In this study, exo-tetrahydrodicyclopentadiene was selected as a model endothermic fuel and experiments on endothermic properties were investigated with pore structure controlled zeolite catalyst using metal deposition. We secured the catalyst that had better endothermic performance than commercial catalyst. The object of this study is inspect catalyst properties which have effect on heat absorption improvement. Synthetic catalyst could be applied to system that use exo-THDCP as endothermic fuel instead of other commercial catalyst.

• Journal of Aerospace System Engineering
• /
• v.17 no.1
• /
• pp.16-23
• /
• 2023

The aircraft fuel system performs a number of functions such as supplying fuel, transferring fuel between fuel tanks, and measuring the amount of residual fuel in each fuel tank. Since it is a direct cause of fire hazard in crash incident, it is a must to improve survivability of crew members by designing the airframe to tolerate expected crash impact. The civil aviation authority requires intensive verification of the fuel system design to determine precise application of the airworthiness requirement. Research activity on airworthiness certification criteria and verification scheme is still insufficient, although it has a significant importance. In this paper, as part of a study to improve flight safety by developing guidelines for demonstrating fuel system crash resistance, analysis results of fuel system crash-related airworthiness certification standards, verification scheme, and cases study applicable to military rotorcraft have been reviewed.

• Journal of Aerospace System Engineering
• /
• v.17 no.4
• /
• pp.110-117
• /
• 2023

In this paper, the optimal placement of the rotary wing's communication and navigation antennas was evaluated by measuring their performance through ground simulations and flight tests. To select the mounting position of the communication and navigation antenna on the helicopter, after considering the shape and characteristics of the airframe, the radiation patterns, coupling analysis, equipment operation profiles, and antenna type analysis were performed for the aircraft-mounted antenna. Based on the analysis results, a procedure for sequentially performing voltage standing wave ratio (VSWR) measurement and antenna pattern test was established through ground and flight tests of the antenna. The systematic performance measurement method and procedure proposed in this paper were verified through ground and flight tests of the Light Armed Helicopter (LAH) system.

• Journal of the Korean Society of Systems Engineering
• /
• v.19 no.1
• /
• pp.64-78
• /
• 2023

This paper introduces urban air mobility (UAM) and the definition and types of vertiports required for UAM operations. It also examines domestic policy trends related to UAM and identifies UAM routes in Seoul currently planned by the government. To do so, we reviewed prior research on vertiports, analyzed new regulations from the European Aviation Safety Agency, and studied domestic vertiport specifications and deployment plans for UAM operations based on the size of the S-A1 airframe being developed by Hyundai, and applied them to Samsung Station, the core area of the demonstration routes. Next, using the 'Travel Time Savings Ratio', a method for evaluating transportation economics, we compared and analyzed the time taken by passenger vehicles and the time saved by using UAMs to derive a highly economical demonstration route. As a result, the Samsung Station↔Cheongnyangri Station section was found to be the most efficient. These findings are expected to be utilized for adjusting the distribution of UAMs when operating the demonstration route in the future.