• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.5
• /
• pp.403-413
• /
• 2010

Transition location of boundary layers over airfoils is predicted by using PSE(Parabolized Stability Equations) and $e^N$-method. Growth rates of disturbances are obtained from the PSE analysis and the N-factor curves are calculated by integrating the growth rates. The computational code developed in the present study is validated by comparing the computed results with the well known data for the cases of flat plate boundary layers and airfoils. Predictions of transition location are made for the boundary layers over NACA0012, NLF(1)-0414F, and NLF(1)-0416 airfoil. Predicted transition locations are found to be in good agreement with the experimental data.

• Journal of Biosystems Engineering
• /
• v.37 no.1
• /
• pp.1-10
• /
• 2012

Purpose: The most important element of an agricultural helicopter is the rotor blade realizing lift force. In order to improve the performance of the rotor blades, two types (KA152313 and KB203611) of airfoils were designed and compared. Methods: The nose shape of the KB203611 airfoil was 'drooped' and 'sharp' compared to the leading edge of the KA152313 airfoil. The performance of the experimental airfoils was simulated using CFD-ACE program, and lifts were measured in situ using the 'AgroHeli-4G', a prototype helicopter. Results: Simulated lifts of the blade with the KA152313 airfoil showed proper values for a wide range of angles of attack between $14^{\circ}{\sim}18^{\circ}$, while the simulated lift of the KB203611 blade exhibited maximum values near $13^{\circ}{\sim}14^{\circ}$. In the lift measurements, the range of operable angles of attack was a collective pitch angle at the grip (GP) of $12^{\circ}{\sim}18^{\circ}$ for the KA152313 blade. On the other hand, the range of angles of attack for the KB203611 blade was a GP of $12^{\circ}{\sim}14^{\circ}$. Conclusions: The blade of KA152313 performed well over a wide range of AoAs and the blade of KB203611 performed better at low AoAs. In this study, a variative airfoil blade, gradually emerging from grip to tip using the two different airfoils, was suggested.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.1 no.1
• /
• pp.145-153
• /
• 1998

In the direct numerical optimization method, the aerodynamic coefficients of the airfoil designed by one-point design can be deteriorated at other operating points. Therefore, the capacity of the multi-point design is indispensable for actual airfoil design. In this paper, the two-point design of transonic airfoils is studied based on the Navier-Stokes equations flow solver and the feasible direction optimization algorithm, and the effects of weighting parameter were analyzed and compared. The results show that the airfoils designed by two-point design satisfy the performances at the peripheral regions of two operating points concurrently and have the favorable aerodynamic characteristics at the point which has larger weighting parameter than the other point.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.46-52
• /
• 2010

In the present work, the aerodynamic characteristics of elliptic airfoils which have a 12% thickness ratio are numerically investigated based on Reynolds-averaged Navier-Stokes equations and a transition SST model at a Reynolds number 8.0$\times$105. The numerical simulation of a synthetic jet actuator which is a well-known zero-net-mass active flow control actuator located at x/c = 0.00025, was performed to control massive flow separation around the leading edge of the elliptic airfoils. Four cases of non-dimensional frequencies were simulated at an angle of attack of 12 degree. It is found that the size of the vortex induced by synthetic jets was getting smaller as the jet frequency becomes higher. Comparison of the location of synthetic jets between x/c = 0.00025 (around the leading edge) and x/c = 0.9 (near the separation) shows that the control near the leading edge induces closed recirculation flow regions caused by the interaction of the synthetic jet with the external flow, but the control applied at 0.9c (near the trailing edge) induces a very small and weak vortex which quickly decays due to weak intensity.

• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.4
• /
• pp.374-382
• /
• 2014

This paper presents the computational aerodynamic analysis of a long-endurance UAV that was developed by the Korea Aerospace Research Institute (KARI), named EAV-2. EAV-2 is a technical demonstrator of aerodynamically efficient design, as well as a hybrid electric-propulsion system for future long-endurance UAVs. We evaluated the aerodynamic characteristics of six low-Reynolds number airfoils, using a panel method code, XFOIL, to select an optimal airfoil for the long-endurance mission of EAV-2. The computational results by a CFD code, FLUENT, suggested that the aerodynamic performance of EAV-2 would be notably improved after adopting SG6043 airfoil, and modifying the fuselage design. This reduced the total drag by 43%, compared to that of a previous KARI model, EAV-1, at the target lift of $C_L=1.0$. Also, we achieved a drag reduction of approximately 14% by means of the low-drag fuselage configuration.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.90-96
• /
• 2009

In this study, a generic airfoil designed by the inverse method was evaluated with several candidate airfoils as a first step. Each airfoil was compared with respect to aerodynamic performance to meet the requirement of HALE(high altitude long endurance) aircraft. The second step was to optimize the candidate airfoil using the couple of optimization formulations to down select an optimum airfoil. For the analysis of low Reynolds number 2D flow, Drela's MSES was used. After comparing the aerodynamic results, the best airfoil was chosen to construct the baseline 3D wing. The Navier-Stokes code was used to evaluate the overall aerodynamic performance of designed wing with other wings. The results show that the designed wing has the best performance compared with other wings.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.51-56
• /
• 2009

Optimization with metamodel is one of numerical optimization methods. Response surface method is performed for making metamodel. The Hcks-Henne function is used for designing 2D shape of the airfoil and spring analogy is used to change the grid according to the change in shape of the airfoil. Aerodynamic coefficient required for response surface method are obtained by using Navier-Stokes solver with $\kappa-\omega$ shear stress transport turbulence model. For the baseline airfoils, OA 312, OA 309, and OA 407 airfoils select and optimize to improve aerodynamic performance.

• Journal of computational fluids engineering
• /
• v.4 no.3
• /
• pp.44-51
• /
• 1999

A modified version of SST turbulence model is suggested to simulate unsteady separated flows over oscillating airfoils. The original SST model, which shows good performance in predicting various steady flows, often results in oscillatory behavior of aerodynamic loads in large separated flow regions. It is shown that this oscillatory behavior is due to the adoption of the absolute value of vorticity in generalizing the original model. As a remedy, a modification is made such that the vorticity in the original SST model is replaced by strain rate. The present model is verified for a mild separated airfoil flow at fixed angle of incidence and for unsteady flowfields about oscillating airfoils. The results are compared with BSL model and original SST model. It is illustrated that the present model gives a better agreement with the experimental results than other two models.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.28-34
• /
• 2012

In this study, the reliability-based design optimization of the airfoil was performed. PARSEC function was used to consider the uncertainty of the aerodynamic shape for the reliability-based shape optimization of airfoils. Among various reliability analysis methods, the moment method was used to compute the probability of failure of the aerodynamic performance. The accuracy of the reliability analysis was compared with other methods and it was found that the moment method predicts the probability of failure accurately. Deterministic and reliability-based optimizations were performed for the shape of the airfoil and it was demonstrated that reliability-based optimum assures the aerodynamic performances under uncertainties of the shape of the airfoil.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.512-515
• /
• 2009

This research describes on airfoil shape design, crucial to core technique and algorithm optimization for the wind turbine blade development. We grasped the parameter to define the airfoil shape in the wind turbine blade and aircraft, and the important performance characteristic of the airfoil. The airfoil shape function is selected by studying which is suitable for wind turbine blade airfoil development. The selected method is verified by to compare the generated airfoil shape with base airfoil. The new airfoils were created by the selecting shape function based on the well-known airfoil for wind turbine blades. In addition, we performed aerodynamic analysis about the generated airfoils by XFOIL and estimated the point of difference in the airfoil shape parameter using the aerodynamic performance results which is compared with basic airfoil. This result data applies to the fundamental research for a wind turbine blade optimization design and accomplished the aerodynamic analysis manual.