• Phonetics and Speech Sciences
• /
• v.3 no.1
• /
• pp.103-110
• /
• 2011

Idiopathic Parkinson's Disease patients' speech is hypokinetic dysarthria and their speech is possibly the consequence of impaired respiratory support. The purpose of this study was focused on the respiratory characteristics of speech breathing in de novo IPD who were not given prior vocal or anti-Parkinson treatment. A total of 40 subjects participated in the study: 20 de novo IPD patients between the ages of 50 and 80, and 20 normal subjects with similar age, height, and weight matches. Forced Expiratory Vital Capacity (FVC), Forced Expiratory Volume in 1 sec (FEV1) and $FEV_1$ as a percentage of FVC (FEV1/FVC) was measured with a PC-based spirometer (Cosmed). In addition, Maximum Phonation Time (MPT), Mean Airflow Rate (MFR), Subglottal Pressure (Psub) and the number of syllables produced per breath were measured with a Phonatory Aerodynamic System (Kay PENTAX). All subjects were asked to read a standardized Korean paragraph and the following measurements were obtained from the task. Results indicated no statistically significant differences in respiratory function (FEV1/FVC%) and aerodynamic function between the two groups, but the number of syllables per breath was significantly lower in the IPD patient group than in the normal group and it could be predicted by FVC and MFR. Therefore, the study shows that the MFR from the lungs during speech in de novo IPD patients is used inefficiently.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.25 no.2
• /
• pp.94-100
• /
• 2013

A convergent-divergent nozzle or venturi nozzle has been used to accelerate the wind speed at its throat. The wind speed at the throat is inversely proportional to its area according to the continuity equation. In this numerical study, an airflow phenomena in the venturi system placed at a vertical structure was investigated to understand the vortex effect occurred at the rear-side of the vertical structure on the air speed increment at the throat of the venturi system. For this study, a venturi system sized by $20(m){\times}20(m){\times}6(m)$ was modelled and the area ratio(AR) of the model venturi was 2.86. To see the vortex effect on the air flow acceleration in the venturi throat, two different boundary conditions was defined From the study, it was found that the pressure coefficient(CP) of the venturi system with the vortex formed at the exit of the venturi was about 2.5times of the CP of the venturi system without the vortex effect. The velocity increment rate of the venturi system with the vortex was 61% but 9.5% only at the venturi system without the vortex. Conclusively, it can be said that the venturi system installed in a vertical structure has very positive effect on the flow acceleration at its throat due to the vortex formed at the rear-side of the vertical structure.

• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.18 no.1
• /
• pp.44-50
• /
• 2007

Background and Objectives: The 585-nm pulsed dye laser (PDL) has recently been adopted by otolaryngologists because of its epithelial-sparing properties. Many authors have reported the use of PDL for treatment of various vocal cord lesions. This purpose of this study is to examine the effectiveness of 585-nm PDL in the treatment of vocal polyp. Materials and Methods: Eight patients with vocal polyp were treated with 585-nm PDL from Sep. 2006 to Nov. 2006 in Yong-dong Sevrance hospital. 5 of them went through local anesthesia and 3 of them went through general anesthesia. In order to control laser fiber, flexible digital transnasal laryngoscope was applied under local anesthesia and general anesthesia using LMA, and micromanipulator was used under general anesthesia using endotracheal tube. The evaluations of vocal function was done at pre-and postoperation. Results: All patients improved in the perceptual evaluation of voice after PDL surgery. The aerodynamic study revealed that 5 of 8 patients showed improvement in maximal phonation time, and 6 of 8 showed improvement in mean airflow rate during phonation. The acoustic analysis revealed that all patients showed improvement in Jitter and Shimmer, and 7 of 8 showed improvement in noise to harmony ratio. Conclusion: This study demonstrates promising results in the efficacy of 585-nm PDL for the treatment of vocal polyps, and it illustrates a new option for vocal polyp treatment as well as the advantage of PDL surgery.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.5
• /
• pp.9-16
• /
• 2022

Syngas, also known as synthesis gas, synthetic gas, or producer gas, is a combustible gas mixture generated when organic material (biomass) is heated in a gasifier with a limited airflow at a high temperature and elevated pressure. The present research was aimed at modifying the existing LPG engine generator for fully operated syngas. During this study, the designed gasifier-powered woodchip biomass was used for syngas production to generate power. A 6.0 kW LPG engine generator was modified and tested for operation on syngas. In the experiments, syngas and LPG fuels were tested as test fuels. For syngas production, 3 kg of dry woodchips were fed and burnt into the designed downdraft gasifier. The gasifier was connected to a blower coupled with a slider to help the air supply and control the ignition. The convection cooling system was connected to the syngas flow pipe for cooling the hot produce gas and filtering the impurities. For engine modification, a customized T-shaped flexible air/fuel mixture control device was designed for adjusting the correct stoichiometric air-fuel ratio ranging between 1:1.1 and 1.3 to match the combustion needs of the engine. The composition of produced syngas was analyzed using a gas analyzer and its composition was; 13~15 %, 10.2~13 %, 4.1~4.5 %, and 11.9~14.6 % for CO, H₂, CH₄, and CO₂ respectively with a heating value range of 4.12~5.01 MJ/Nm³. The maximum peak power output generated from syngas and LPG was recorded using a clamp-on power meter and found to be 3,689 watts and 5,001 watts, respectively. The results found from the experiment show that the LPG engine generator operated on syngas can be adopted with a de-ration rate of 73.78 % compared to its regular operating fuel.

• Advances in aircraft and spacecraft science
• /
• v.10 no.2
• /
• pp.107-125
• /
• 2023

Drag reduction is significant research in aircraft design due to its effect on the cost of operation and carbon footprint reduction. Aircraft currently use conventional solid winglets to reduce the induced drag, adding extra structural weight. Fluidic on-demand winglets can effectively reduce drag for low-speed flight regimes without adding any extra weight. These utilize the spanwise airflow from the wingtips using hydraulic actuators to create jets that negate tip vortices. This study develops a computational model to investigate fluidic on-demand winglets. The well-validated computational model is applied to investigate the effect of injection velocity and angle on the aerodynamic coefficients of a rectangular wing. Further, the turbulence parameters such as turbulent kinetic energy (TKE) and turbulent dissipation rate are studied in detail at various velocity injections and at an angle of 30°. The results show that the increase in injection velocity shifted the vortex core away from the wing tip and the increase in injection angle shifted the vortex core in the vertical direction. Further, it was found that a 30° injection is efficient among all injection velocities and highly efficient at a velocity ratio of 3. This technology can be adopted in any aircraft, effectively working at various angles of attack. The culmination of this study is that the implementation of fluidic winglets leads to a significant reduction in drag at low speeds for low aspect ratio wings.

• Membrane Journal
• /
• v.21 no.1
• /
• pp.46-54
• /
• 2011

In this study, combined effect of airflow rate, $TiO_2$ concentration, solution pH and $Ca^{+2}$ addition on HA (humic acid) fouling in submerged, photocatalytic hollow-fiber microfiltraiton was investigated systematically. Results showed that UV irradiation alone without $TiO_2$ nanoparticles could reduce HA fouling by 40% higher than the fouling obtained without UV irradiation. Compared to the HA fouling without UV irradiation and $TiO_2$ nanoparticles, the HA fouling reduction was about 25% higher only after the addition of $TiO_2$ nanoparticles. Both adsorptive and hydrophilic properties of $TiO_2$ nanoparticles for the HA can be involved in mitigating membrane fouling. It was also found that the aeration itself had lowest effect on fouling mitigation while the HA fouling was affected significantly by solution pH. Transient behavior of zeta potential at different solution pHs suggested that electrostatic interactions between HA and $TiO_2$ nanoparticles should improve photocatalytic efficiency on HA fouling. $TiO_2$ concentration was observed to be more important factor than airflow rate to reduce HA fouling, implying that surface reactivity on $TiO_2$ naoparticles should be important fouling mitigation mechanisms in submerged, photocatalyic microfiltraiton. This was further supported by investigating the effect of $Ca^{+2}$ addition on fouling mitigation. At higher pH (= 10), addition of $Ca^{+2}$ can play an important role in bridging between HA and $TiO_2$ nanoparticles and increasing surface reactivity on nanoparticles, thereby reducing membrane fouling.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.2
• /
• pp.73-78
• /
• 2022

This experiment was conducted to establish the technology for artificial hay preparation in Korea. Using far-infrared heater, a device that can control temperature, airflow, and far-infrared radiation was produced and conducted on the fourth harvested alfalfa. The drying conditions were carried out by selecting a total of four conditions. For each condition, the radiation rate was set to around 40% (33-42%), and the temperature was set at 58~65℃, and the speed of the airflow was fixed at 60m/s. The overall drying time was set to 30 min in the single and 60 min (30-30 min) and 90 min (30-30-30 min) in the complex condition, and the radiation rate and temperature were changed by time period. In the case of drying condition 1, the final dry matter (DM) content was 46.26%, which did not reach a DM suitable for hay. However, all of the alfalfa corresponding to the remaining drying conditions 2 to 7 showed a DM content of 80% or more, resulting in optimal alfalfa hay production. In power consumption according to the drying conditions, the second drying condition showed the lowest at 4.7 KW, and the remaining drying conditions were as high as 6.5 to 7.1 KW. The crude protein content was found to be high at an average of 25.91% and it showed the highest content in the 5th drying condition (26.93%) and the lowest value in the 6th drying condition (25.16%). The digestibility showed a high value with an average of 84.90%, and there was no significant difference among treatments (p>0.05). Considering the above results, it was judged that drying condition 2 was the most advantageous.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.4
• /
• pp.378-383
• /
• 2013

A butterfly throttle valve has been used to control the brake power of an SI engine by controlling the mass flow-rate of intake air in the induction system. However, the valve has a serious effect on the volumetric efficiency of the engine due to the pressure resistance in the induction system. In this study, a new intake air controlling valve named "Variable Geometry Throttle Valve(VGTV)" is proposed to minimize the pressure resistance in the intake system of an SI engine. The design concept of VGTV is on the application of a venturi nozzle in the air flow path. Instead of change of the butterfly valve angle in the airflow field, the throat width of the VGTV valve is varied with the operating condition of an SI engine. In this numerical study, CFD(computational fluid dynamics) simulation technique was incorporated to have an aerodynamics performance analysis of the two air flow controlling systems; butterfly valve and VGTV and compared the results to know which system has lower pressure resistance in the air intake system. From the result, it was found that VGTV has lower pressure resistance than the butterfly valve. Especially VGTV is effective on the low and medium load operating condition of an SI engine. The averaged pressure resistance of VGTV is about 49.0% lower than the value of the conventional butterfly throttle valve.

• Journal of Korean Society of Environmental Engineers
• /
• v.30 no.9
• /
• pp.948-954
• /
• 2008

Membrane bioreactor(MBR) processes have been widely applied to wastewater treatment for last decades due to its excellent capability of solid-liquid separation. However, membrane fouling was considered as a limiting factor in wide application of the MBR process. Excess aeration into membrane surface is a common way to control membrane fouling in most MBR. However, the excessively supplied air is easily dissipated in the reactor, which results in consuming energy and thus, it should be modified for effective control of membrane fouling. In this study, cylindrical tube was introduced to MBR in order to use the supplied air effectively. Membrane fibers were immersed into the cylindrical tube. This makes the supplied air non-dissipated in the reactor so that membrane fouling could be controlled economically. Two different air supplying method was employed and compared each other; nozzle and porous diffuser which were located just beneath the membrane module. Transmembrane pressure(TMP) was monitored as a function of airflow rate, flux, and ratio of the tube area and cross-sectioned area of membrane fibers(A$_m$/A$_t$). Flow rate of air and liquid was regulated to obtain slug flow in the cylindrical tube. With the same flow of air supply, nozzle was more effective for controlling membrane fouling than porous diffuser. Accumulation of sludge was observed in the tube with the nozzle, if the air was not suppled sufficiently. Reduction of membrane fouling was dependent upon the ratio, A$_m$/A$_t$. For diffuser, membrane fouling was minimized when A$_m$/A$_t$ was 0.27, but 0.55 for nozzle.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.42 no.4
• /
• pp.258-263
• /
• 2022

This experiment was conducted to confirm the possibility of manufacturing artificial Italian ryegrass hay using far-infrared rays in Korea. The machine used in this experiment was a far-infrared ray dryer capable of adjusting temperature, airflow, and far-infrared radiation, and was conducted on Italian ryegrass harvested in May. Conditions for drying were performed by selecting a total of nine conditions, and each condition was set to emission rate of 42 to 45%, and the internal temperature was set to 65℃. The speed of the air flow in the machine was 40-60 m/s, and the overall drying time was 30 minutes for 42% radiation, 25 minutes for 43% radiation, and 20 minutes for 45% radiation. The final dry matter content according to each drying condition was 88.5% on average, and the dry matter content suitable for hay was shown in the all treatment. Looking at the power consumption according to the drying conditions, the lowest was found in the treatment that dried for 20 minutes at 45% radiation. In the drying rate, there was no difference in drying conditions 1 to 5, but a significantly low tendency was shown in conditions 6 to 7. In terms of feed value, CP and IVDMD were higher than raw materials in most drying conditions, and ADF and NDF contents were low, and tended to be high in drying conditions 4, 7, and 8. Through the above results, it was judged that drying conditions 7 and 8 were the most advantageous when considering drying speed, power consumption, and quality.