• Asian Journal of Atmospheric Environment
• /
• v.6 no.2
• /
• pp.118-126
• /
• 2012

To investigate the effect of aircraft traffic emissions on soil pollution, metal levels were analyzed for 8 metals (Fe, Cr, Pb, Zn, Cu, Ni, Mn and Cd) from the vicinity of the Indira Gandhi International (IGI) airport in Delhi, India. The texture of the airport soil was observed to be sandy. Among the metals, Cd showed minimum concentration ($2.07{\mu}g\;g^{-1}$), while Fe showed maximum concentration ($4379{\mu}g\;g^{-1}$). The highest metal accumulation was observed at the landing site. Significant correlations were observed between metals and different textures (sand, silt, and clay) as well as with organic carbon (OC). The results indicate that grain size play a major role in OC retention in soil and subsequently helps in adsorption of metals in soil. M$\ddot{u}$ller's geoaccumulation index (I-geo) showed that airport soil was contaminated due to Cd and Pb with the pollution class 2 and 1, respectively. Pollution load index of the airport site was 1.34-3 times higher than the background site. The results of factor analysis suggested that source of the soil metal is mainly from natural weathering of soil, aircraft exhaust, and automobile exhaust from near by area. With respect to Dutch target values, the airport soils showed ~3 times higher Cd concentration. The study highlighted the future risk of enhanced metal pollution with respect to Cd and Pb due to aircraft trafficking.

• International Journal of Aeronautical and Space Sciences
• /
• v.13 no.2
• /
• pp.229-237
• /
• 2012

In this study, the failure mechanism of sandwich-to-laminate T-joints under pull-off loading was investigated by experiment and the finite element method. A total of 26 T-joint specimens were manufactured and tested in order to investigate the effects of both adhesive thickness (0.4, 2.0, and 4.0 mm) and environmental conditions on the failure of the joints. The results showed that failure occurred mainly as intralaminar failure in the first layer of the sandwich face, which was contacted to the paste adhesive. The failure load did not significantly change with increasing adhesive thickness in both RTD (Room Temperature and Dry) and ETW (Elevated Temperature and Wet) conditions. In the case of ETW conditions, however, the failure load increased slightly with an increase in adhesive thickness. The joints tested in ETW conditions had higher failure loads than those tested in RTD conditions. In addition to the experiment, a finite element analysis was also conducted to investigate the failure of the joint. The stress inside the first ply of the sandwich face was of interest because during the experiment, failure always occurred there. The analysis results showed good agreement with the trend of experimental results, except for the case of the smallest adhesive thickness. The highest stress was predicted in the regions where initial failure was observed in the experiment. The maximum stress was almost constant when the adhesive thickness was beyond 2 mm.

• Advances in aircraft and spacecraft science
• /
• v.6 no.2
• /
• pp.117-144
• /
• 2019

High Altitude and Long Endurance (HALE) aircraft are capable of providing intelligence, surveillance and reconnaissance (ISR) capabilities over vast geographic areas when equipped with advanced sensor packages. As their use becomes more widespread, the demand for additional range, endurance and payload capability will increase and designers are exploring non-conventional configurations to meet the increasing demands. One such configuration is the joined-wing concept. A joined-wing aircraft is one that typically connects a front and aft wings in a diamond shaped planform. One such example is the Boeing SensorCraft configuration. While the joined-wing configuration offers potential benefits regarding aerodynamic efficiency, structural weight, and sensing capabilities, structural design requires careful consideration of elastic buckling resulting from the aft wing supporting, in compression, part of the forward wing structural loading. It has been shown already that this is a nonlinear phenomenon, involving geometric nonlinearities and follower forces that tend to flatten the entire configuration, leading to structural overload due to the loss of the aft wing's ability to support the forward wing load. Severe gusts are likely to be the critical design condition, with flight control system interaction in the form of Gust Load Alleviation (GLA) playing a key role in minimizing the structural loads. The University of Victoria Center for Aerospace Research (UVic-CfAR) has built a 3-meter span scaled and flexible wing UAV based on the Boeing SensorCraft design. The goal is to validate the nonlinear structural behavior in flight. The main objective of this research work is to perform Ground Vibration Tests (GVT) to characterize the dynamic properties of the scaled flight vehicle. Results from the experimental tests are used to characterize the modal dynamics of the aircraft, and to validate the numerical models. The GVT results are an important step towards a safe flight test program.

• Steel and Composite Structures
• /
• v.43 no.1
• /
• pp.19-30
• /
• 2022

The static strength and fatigue crack resistance of the aircraft skin structures depend on the materials used and joint type. Most of the commercial aircraft's skin panel structures are made from aluminium alloy and carbon fibre reinforced epoxy. In this study, the fatigue resistance of four joint configurations (metal/metal, metal/composite, composite/composite and composite/metal) with riveted, adhesive bonded, and hybrid joining techniques are investigated with experiments and finite element analysis. The fatigue tests were tension-tension because of the typical nature of the loads on aircraft skin panels susceptible of experimenting fatigue. Experiment results suggest that the fatigue life of hybrid joints is superior to adhesive bonded joints, and these in turn much better than conventional riveted joints. Thanks to the fact that, for hybrid joints, the adhesive bond provides better load distribution and ensures load-carrying capacity in the event of premature adhesive failure while rivets induce compressive residual stresses in the joint. Results from FE tool ABAQUS analysis for adhesive bonded and hybrid joints agrees with the experiments. From the analysis, the energy release rate for adhesive bonded joints is higher than that of hybrid joints in both opening (mode I) and shear direction (mode II). Most joints show higher energy release rate in mode II. This indicates that the joints experience fatigue crack in the shear direction, which is responsible for crack opening.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.7
• /
• pp.507-514
• /
• 2022

The EO/IR targeting pod mounted on a fighter to acquire information about tactical targets is typically mounted and operated at the bottom of the aircraft fuselage. Since the aircraft equipped with such an external attachment has complexed aerodynamic and inertial characteristics compared to the aircraft flying without an external attachment, a method of system performance analyses is required to identify development risk factors in the early stages of development and reflect them in the design. In this study, a development plan was presented to provide the necessary modeling and simulation tools to develop a pod that can acquire measurement data stably in a highly maneuverable environment. The limiting operating conditions of the pods mounted on the highly maneuverable aircraft were derived, the aerodynamics and inertial loads of the mounted pods were analyzed according to the limiting operating conditions, and a flight data generation and transmission system were developed by simulating the mission of the aircraft equipped with the mounted pods.

• Journal of Aerospace System Engineering
• /
• v.15 no.1
• /
• pp.80-85
• /
• 2021

In this study, for conducting a static load test of an external fuel tank used for an aircraft, the flight load acting on the external fuel tank was converted to the test load and the suitability of the converted test loads was confirmed. In order to calculate the test load from the flight load, the external fuel tank was divided into several sections. Shear load, moment by unit shear load, and unit moment were calculated for each section. Test loads for each section were then calculated by computing the shear load, the moment of each section, and flight load condition. In actual static load tests, it might not be possible to impose the test load in the calculated position due to physical constraints. Therefore, after determining positions in which the load could be imposed in the actual test, the test load calculated for each section was redistributed to selected positions. Finally, a test load plan was established by applying a whiffle tree to enhance the efficiency of the test performance while making it easier to operate the actuator. The reliability of the test load plan was verified by comparing it with flight load conditions.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1647-1650
• /
• 1997

This paper presents the control law of Automatic Rudder Trim System(ARTS) for the KTX-1. The proposed ARTS is designed mainly t reduce the pilot's work load for trimming in the various conditiions of engine torque. airspeed, and aircraft configuration. The ARTS partially compensates the transient yawing motion due to change of engine power in turboprop aircraft because of the limitation of the actuation speed of the trim motor. In this paper flight test data are analyzed to understand the phenomena and the dynamics of the reversible rudder flight control system is derived. Finally, the control concept and conrtol law of ARTS are described and the characteristics of the ARTS are analyzed through simulation study.

• Journal of Aerospace System Engineering
• /
• v.9 no.2
• /
• pp.19-24
• /
• 2015

Export basic trainer was designed to add armed configuration required by customer. Design configuration of main wing was changed to satisfy changed internal load caused by armed configuration. It was verified that design changed main wing airframe of export basic trainer satisfy the requirement through the structural detail analysis, structural ground test and flight test. This paper presents the durability test procensure and test result for the main wing of export basic trainer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.514-519
• /
• 2003

The aircraft engine is usually supported by rolling element bearings and has a small damping rate, which is vol y sensitive to external force. The high-performance requirement of the rotors leads to complex assembly designs and are more flexible. Squeeze film dampers (SFDs) are introduced to provide damping while crossing the critical speeds and stability to the rotor s :stem. Hence, the focus of the present investigation is on the decision of an optimal size of the flexible rotor system supported by the squeeze film dampers to minimize the maximum transmitted load and unbalance response over a range operating speeds. The enhanced genetic algorithm (EGA), which was developed by authors, is used in the optimization process. This algorithm is based on the synthesis of a modified genetic algorithm and simplex method. The results show significant benefits in using EGA when compared with nonlinear programming (NLP).

• Journal of Aerospace System Engineering
• /
• v.1 no.4
• /
• pp.22-27
• /
• 2007

The 150 gal Ion EFT(External Fuel Tank) used to enlarge the aircraft operation range was adopted an import equipment in T-50 FSD phase. But in Production phase the EFT was planed to develop for the stable ILS(Integrated Logistics Support) and technical ability improvement by using the composite materials. The design for configuration and fuel system is intended to maintain compatibility with aircraft systems and the development test is performed on component, assembly and aircraft. This study is conducted to provide the technology of design and test for the 150 gallon composite EFT in LRU level. The test results show that the composite EFT is satisfied with structural, functional and environment requirements which are described in specification.