• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.169-178
• /
• 2001

Among the recent research ideas to reduce hydrocarbon emissions emitted from SI engines till light-off of catalyst since cold start are those exploiting non-thermal plasma technique and photo-catalyst that draws recent attention by virtue of its successful application to practical use to clean up the atmosphere using the feature of its relative independence on temperature. Based on the previous research results obtained with model exhaust gases using an experimental emissions reduction system that utilizes the non-thermal plasma and photo-catalyst technique, further investigation was conducted on a production N/A 1.5 liter DOHC engine during cold start to warm-up. For the effects of non-thermal plasma-photocatalyst combined reactor, 10% concentration reduction was achieved with the fuel component paraffins, and the large increase in non-fuel paraffinic components and acetylene concentrations were similar to those of base condition. However the absolute value was locally a bit higher than those of base condition since the products was made from the dissociation and decomposition of highly branched paraffins by plasma-photocatalyst reactor. Olefinic components were highly decomposed by about 75%, due to these excellent decompositions of olefins which have relatively high MIR values, and the SR value was 1.87 that is 30% reduction from that of base condition, then, the photochemical reactivity was lowered.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.40 no.1
• /
• pp.35-40
• /
• 2017

A most important progress in civilization was the introduction of mass production. One of main methods for mass production is die-casting molds. Due to the high velocity of the liquid metal, aluminum die-casting is so complex where flow momentum is critical matter in the mold filling process. Actually in complex parts, it is almost impossible to calculate the exact mold filling performance with using experimental knowledge. To manufacture the lightweight automobile bodies, aluminum die-castings play a definitive role in the automotive part industry. Due to this condition in the design procedure, the simulation is becoming more important. Simulation can make a casting system optimal and also elevate the casting quality with less experiment. The most advantage of using simulation programs is the time and cost saving of the casting layout design. For a die casting mold, generally, the casting layout design should be considered based on the relation among injection system, casting condition, gate system, and cooling system. Also, the extent or the location of product defects was differentiated according to the various relations of the above conditions. In this research, in order to optimize the casting layout design of an automotive Oil Pan_BR2E, Computer Aided Engineering (CAE) simulation was performed with three layout designs by using the simulation software (AnyCasting). The simulation results were analyzed and compared carefully in order to apply them into the production die-casting mold. During the filling process with three models, internal porosities caused by air entrapments were predicted and also compared with the modification of the gate system and overflows. With the solidification analysis, internal porosities occurring during the solidification process were predicted and also compared with the modified gate system.

• Food Science and Preservation
• /
• v.16 no.2
• /
• pp.253-258
• /
• 2009

This study investigated the effects of mycelium and culture supernatant of Cordyceps ochraceostromat(Co) on air way hyper-responsiveness, pulmonary immune cell infiltration, and Th2 cytokine expression in animal models of atopy and asthma. After ConA(+/-) activation of mouse primary spleen cells, decreased IL-4 and IL-13 cytokine production were seen in the presence of Co mycelium extracts and culture supernatant. The asthma model involved mice sensitized to ovalbumin by i.p. injection treatment; Co mycelium extract was also injected. The atopy model was the dinitrofenylbenzene-treated mouse ear. Ear thicken ing induced by DNFB was decreased by Co mycelium extract, and the extract also inhibited lung cell infiltration in ovalbumin-induced asthmatic mice. The results thus indicated that the Co mycelial extract reduced the undesirable immune responses seen in asthma and atopy.

• 연구논문집
• /
• s.27
• /
• pp.75-86
• /
• 1997

Combined cycle power plant is a system where a gas turbine or steam turbine is used to produce shaft power to drive a generator for producing electrical power and the steam from the HRSG is expanded in a steam turbine for additional shaft power. Combined cycle plant is a one from of cogeneration. The temperature of the exhaust gases from a gas turbine ranges from $400^\circC$ to $600^\circC$, and can be used effectively in a heat recovery steam generator to produce steam. Combined cycle can be classed as a "topping(gas turbine)" and a "bottoming(steam turbine)" cycle. The first cycle, to which most of the heat is supplied, is called the topping cycle. The wasted heat it produces is then utilized in a second process which operates at a lower temperature level and is therefore referred to as a "bottoming cycle". The combination of gas/steam turbine power plant managed to be accepted widely because, first, each individual system has already proven themselves in power plants with a single cycle, therefore, the development costs are low. Secondly, the air as a working medium is relatively non-problematic and inexpensive and can be used in gas turbines at an elevated temperature level over $1000^\circC$. The steam process uses water, which is likewise inexpensive and widely available, but better suited for the medium and low temperature ranges. It, therefore, is quite reasonable to use the steam process for the bottoming cycle. Only recently gas turbines attained inlet temperature that make it possible to design a highly efficient combined cycle. In the present study, performance analysis of a dual pressure combined-cycle power plant is carried out to investigate the influence of topping cycle to combined cycle performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.4
• /
• pp.371-377
• /
• 2011

The aim of this study is to investigate the effects of aromatics and T90 temperature for high cetane number (CN) of diesel fuels on combustion and exhaust emissions in low-temperature diesel combustion in a 1.9 L common rail direct injection diesel engine at 1500 rpm and 2.6 bar BMEP. Four sets of fuels with CN 55, aromatic content of 20% or 45% (vol. %), and T90 temperature of $270^{\circ}C$ or $340^{\circ}C$ were tested. Given engine operating conditions, all the fuels showed the same tendency of decrease of PM with an increase of an ignition delay time. At the same ignition delay time, the fuels with high T90 produced higher PM. At the same MFB50% location the amount of NOx was similar for all the fuels. Furthermore, at the same ignition delay time the amounts of THC and CO were similar as well for all the fuels. The amount of THC and CO increased with an extension of the ignition delay time mainly because of the increase of fuel-air over-mixing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.5
• /
• pp.724-732
• /
• 2002

Although the demands for diesel engine is increased, our world is faced with very serious problems related to the air pollution due to the exhaust emissions of the diesel engine. In this study, the potential possibility of oxygenated fuel such as Methyl tertiary butyl ether (MTBE) was investigated for the sake of exhausted smoke reduction from diesel engine. MTBE has been used as a fuel additive blended into unleaded gasoline to improve octane number, but the study of application for diesel engine was incomplete. Because MTBE includes oxygen content approximately 18%, it is a kind of oxygenated fuel that the smoke emission of MTBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at high load and speed in diesel engine. But, the NOx emission of MTBE blended fuel is increased compared with commercial diesel fuel. And. it was tried to analyze not only total hydrocarbon but individual hydrocarbon components from $C_1$to $C_{6}$ in exhaust gas using gas chromatography to seek the reason for remarkable reduction of smoke emission. The results of this study show three conclusions. 1. The smoke omission of the MTBE blended fuel is lower than that of the diesel fuel at all experimental region in direct injection diesel engine. 2. Individual hydrocarbons(C$_1$~ $C_{6}$) as well as total hydrocarbon of oxygenated fuel are reduced remarkably compared with diesel fuel. 3. Smoke emission from diesel engines was strongly depended on oxygen content in fuel regardless of operating condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.3
• /
• pp.31-39
• /
• 1999

In this paper, numerical experiment is attempted to analyze and compare the combustion efficiency of the burning sprays due to OFO, FOF triplet / FOOF split doublet injectors. Preconditioned Wavier-Stokes equation system with low Reynolds number $\kappa$-$\varepsilon$ model for turbulence closure, is LU-SGS time-integrated. Spray processes are modeled by DSF analysis with experimentally determined injection characteristics. n-heptane/air global reaction model approximates the combustion for simplicity, and the influence of turbulence on the chemical reaction is included using eddy dissipation model. The results showed the FOF triplet injector of highest combustion efficiency, whereas the OFO type of poet performance. It was also observed that the droplet mean diameter and the average gas temperature due to the mixing efficiency, are the representative parameters for the performance design of combustion.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.5
• /
• pp.24-31
• /
• 2010

Combustion-stability rating of impinging-jet injector is conducted numerically using hot-fire simulation in a subscale chamber with the five-element injector head. A sample F(fuel)-O(dxidizer)-O-F impinging-jet injector is adopted. In this work, instantaneous chemical reaction is adopted for hot-fire simulation based on the assumption that mixing process of fuel and oxidizer streams is controlling. The model chamber was designed based on the methodologies proposed in the previous work regarding geometrical dimensions and operating conditions. The present stability boundaries are in a good agreement with air-injection and hot-fire experimental data. The proposed numerical method can be applied cost-effectively to stability rating of jet injectors when mixing of fuel and oxidizer jets is the dominant process in instability triggering.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.1
• /
• pp.83-87
• /
• 2008

We have a lot of interest in alternative fuels to provide energy independence from oil producing country and to reduce exhaust emissions for air pollution prevention. Biodiesel, which can be generated from natural renewable sources such as new or used vegetable oils or animal fats, may be used as fuel without change of engine structure in diesel engine of compression ignition engine. In this paper, the test results on specific fuel consumption and exhaust emissions of neat diesel oil and biodiesel blends(10 vol.% biodiesel and 20 vol.% biodiesel) were presented using four stroke, direct injection diesel engine. Especially this biodisel was produced from rape oil at our laboratory by ourselves. This study showed that specific fuel consumption and NOx emission were slightly increased, on the other hand CO emission and Soot were tolerably decreased more in the case of biodiesel blends than neat diesel oil.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.2
• /
• pp.157-163
• /
• 2020

Recently, fine dust has been known to cause cardiovascular diseases here, raising interest in ways to reduce emissions by efficiently using fuel from cars that cause air pollution. Accordingly, a driving assistance system was developed to save fuel by eco-driving and improve the driver's bad driving habits. The system was developed using raspberry pi, arduino and Android. Using RPM, speed, fuel injection information obtained from OBD-II, and gyro-sensor values, Fuel-Cut is induced to create an optimal inertial driving environment. It also provides various information system such as weather, driving environment, and preventing drowsy driving through GUI and voice recognition functions. It is possible to check driving records and vehicle fault information using Android application and has low overhead for message transmission using MQTT protocol optimized for IoT environment.