• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.205-212
• /
• 1998

In this study, the effects of water vapor in inlet air on combustion efficiency, general performance, knock characteristics and emission gas concentration were investig- ated through the experiments of combustion and vibration analyses, emission gas analysis by changing water vapor quantity in inlet air with temperature and humidity auto control unit. With partial vapor pressure increase, the brake torque at wide open throttle status decreased and the average ignition delay angle increased, IMEP (indicated mean effective pressured using the integral and 3rd derivatives of filtered cylinder pressure as knock intensity, which matched well with the method of frequency power spectrum of block vibration signal. Water vapor in intake air had influence on the spark knock sensitivity. With the increase of water vapor content in intake air NOx emission was decreased and HC emission was increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.7
• /
• pp.877-884
• /
• 2004

In this paper, structural analysis is performed to investigate the deformation of porous media in a proton exchange membrane fuel cell (PEMFC). Structural deformation of air plate of the fuel cell causes the change in configuration and cross sectional area of the channel. The distributions of mass flow rate and pressure are major factors to decide the performance of a PEMFC. These factors are affected by channel configuration of air plate. Two kinds of numerical air plate models are suggested for flow analyses. Deformed porous media and undeformed porous media are considered for the two models. The Numerical flow analysis results between deformed porous media and undeformed porous media have some discrepancy in pressure distribution. The pressure and velocity distribution under a working condition are numerically calculated to predict the performance of the air plates. Pressure and velocity distributions are compared for two models. It is shown that structural deformation makes difference in flow analysis results.

• Journal of the Society of Disaster Information
• /
• v.18 no.2
• /
• pp.241-251
• /
• 2022

Purpose: In the event of a fire in a high-rise building, if the smoke control area is not effectively protected, smoke or flames enter the stairwell, making it difficult to evacuate. When inflowing air is discharged from a closed corridor, a negative pressure is formed in the corridor, the pressure in the smoke control area becomes excessively high, and the force required to open the door during evacuation is exceeded. Also, if the air introduced into the hallway is not exhausted, the smoke may flow back into the smoke control area. This paper tried to identify the problems caused by the inflowing air and to find out how to improve the performance. Method: Using the CONTAM program, simulations were performed with the basic conditions and the modified conditions. Result: If the inflowing air was discharged from the sealed corridor, overpressure occurred in the Smoke Control Area and exceeded the opening force, and the prevent smoke backflow was insufficient in the layer where the inflowing air was not discharged. Conclusion: "Differential pressure exhaust damper" application, simultaneous opening of two exhaust dampers, and automatic window installation between corridors and outdoors improved the exhaust performance of inflowing air.

• Tribology and Lubricants
• /
• v.21 no.3
• /
• pp.114-121
• /
• 2005

As fuel cell system is environmental friendly generator, its performance depends on its air supply system. Because, fuel cell stack generates electrical energy by electron and the electron is generated by reacting between air and hydrogen. So, more and more compressed air is supplied, more and more the energy can be obtained. In this study, turbo-expander supported by air foil bearing is introduced as the air supply system used by fuel cell systems. The turbo-expander is a turbo machine which operates at high speed, so air foil bearings suit its purpose for the bearing elements. Analysis for confirming the stability and endurance is conducted. Based on FDM and Newton-Raphson method, characteristics of air foil bearing, dynamic coefficients, pressure field and load capacity, are obtained. Using the characteristics of air foil bearing, the rotordynamic analysis is performed by finite element method. The analysis (stability analysis and critical speed map) shows that turbo-expander is stability at running speed. After the analysis, the test process and results are presented. The goals of test are running up to 90,000 RPM, flow rate of 150 $m^3/h$ and pressure ratio of 1.15. The test results show that the aerodynamic performance and stability of turbo-expander are satisfied to the primary goals.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.1
• /
• pp.123-128
• /
• 1994

A high speed spindle system for machine tools can be used to reduce the machining time, to improve the machining accuracy, to perform the machining of light metals and hard materials, and to unite the cutting and grinding processes. In this study, a high speed spindle system is developed by applying the oil-air lubrication method, angular contact ball bearings, injection nozzles with dual orifices, cooling jacket and so on. And an air cooling experiment for evaluating the performance of the spindle system is carried out. Especially, in ofder to establish the air cooling conditions related to the development of a high speed spindle system, the effects of cooling air pressure, oil supply rate, air supply rate and rotational spindle speed are studied and discussed on the bearing temperature rise and frictional torque. Also the effects of cooling air pressure, rotational spindle speed and spindle system structure is investigated on the bearing temperature distribution. The experiment on the test model reveals the usefulness of the air cooling method.

• PNF and Movement
• /
• v.13 no.1
• /
• pp.47-53
• /
• 2015

Purpose: This study examined the effects of space fabric type air insole pressure differences on young adults' dynamic balance ability. Method: The subjects of this study were 17 young female adults without musculoskeletal system disease. Balance ability was measured by dividing the subjects into three groups: an experimental group which did not wear an air insole (insole-off group), an experimental group which wore an air insole to which air pressure of $0.55kg/cm^2$ was applied (insole-0.55 group), and an experimental group which wore an air insole to which air pressure of $0.75kg/cm^2$ was applied (insole-0.75 group). For dynamic balance, the subjects stood on a balance pad, and perimeter length and medium speed were measured three times. The averaged values were recorded and statistically processed. Result: There were significant differences in average speed, and the insole-0.75 group's average speed decreased compared to the insole-off group and the insole-0.55 group. Although the total movement distance did not statistically differ, the insole-75 group's movement distance decreased compared to the insole-off group and the insole-0.55 group. Conclusion: Application of a space fabric type air insole, in particular insole-0.75, was helpful in improving balance ability. This is considered to occur because the space fabric structure was conducive to decreasing sway and producing balance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.1
• /
• pp.17-25
• /
• 2008

To achieve the unidirectional airflow in a cleanroom, we need to predict accurately the static pressure losses at the lower plenum and to control properly the opening pressure ratio of access floor panels based on these pressure losses. At first, the present study proposed a correlation to predict the velocity distribution at the lower plenum, because the accuracy to predict pressure losses at the lower plenum depends on how to calculate the velocity correctly against the inner structures at the lower plenum. In the second place, this study proposed correlations which considered the effect of inner structures such as columns, ducts and equipments at the lower plenum on pressure losses. In order to test the accuracy of these correlations, we compared air flow patterns before regulating the opening ratio of access floor with those after regulating. Results after regulating the opening ratio of access floor show good unidirectional uniform airflow pattern. So the present method can be used as an important tool to control the air flow in a cleanroom.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.12
• /
• pp.1327-1333
• /
• 2013

Air bearings are widely used in precision stages because of low friction and high motion accuracy, however, they suffer from low stiffness in comparison with rolling bearings or hydrostatic bearings. So, several preloading methods using weight, magnet and vacuum force, and opposing pads have been used to increase the stiffness of the air bearings. In this paper, pressure distributions of the vacuum preloaded porous air bearings are calculated using the proposed method. And then, the load capacity and stiffness are analyzed. For the vacuum preloaded air bearings, the stiffness is increased owing to reduced bearing clearance by vacuum force. The simulation results indicate that variation of vacuum pressure with clearance in the vacuum pocket gives rise to low stiffness, so the vacuum pocket should be designed for pressure to be constantly maintained regardless of the bearing clearance by means of large effective pumping speed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.31-38
• /
• 2005

Aerodynamic influence coefficient linearly relates pressure with downwash in panel method for load analysis in which the viscosity of a flow is ignored and the compressibility cannot be taken into account in transonic region. Since the planform of an aerodynamic surface determines the coefficient, the panel method has a limit to the analysis of low Reynolds number flow. The accuracy of the pressure distribution can be improved by a direct correction to the pressure or a correction to the downwash, which is considered the change of camber or thickness, using the aerodynamic coefficients from wind tunnel test as constraints. A premultiplying correction method as well as a postmultiplying correction method is applied to a micro air vehicle to provide more accurate aerodynamic pressure for trim and load analyses. Theoretical aerodynamic pressure is obtained from the panel method. Correction factor matrix and correct pressure coefficient are computed for the conditions with two constraints in addition to single constraint. The postmultiplying correction method gives a better improvement in pressure distribution on micro air vehicle due to the flow characteristics on it.

• Journal of the Korean Solar Energy Society
• /
• v.39 no.6
• /
• pp.27-40
• /
• 2019

Kitchen hoods are limited in discharging all contaminants produced during cooking. Contaminants that have not been discharged can rise to the upper part of the kitchen and become stacked. To solve this problem, there is a way to increase the air volume of the kitchen hood, but there are limits, so a new system is required. This study proposes the Duct System (IADK : Inducing Airflow Duct system for Kitchen hood )through 3D printers and experiments. To do this, the pressure is measured to verify the three levels of air volume provided by the kitchen hood. To check the degree of loss of flow in the existing kitchen hood system, install flexible ducts alone to measure the pressure. Change the internal diameter and type of connection of the IADK and measure the pressure. The air pressure, static pressure difference, and loss factor are calculated and analyzed using the pressure measured through the experiment.