• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.6
• /
• pp.647-653
• /
• 2012

A short reaction mechanism for premixed $CH_4$-air flames at high pressure was developed using a reduction method based on the combined application of the simulation error minimization connectivity method and the iterative species-removal sensitivity method. It consisted of 43 species and 554 elementary reactions under the condition that it produces less than 5% of the maximum error. The flame structures obtained using a detailed reaction mechanism and the short reaction mechanism were compared for $CH_4$-air flames with various initial temperatures and equivalence ratios at high pressure, and the results were in good agreement. Therefore, the short reaction mechanism developed could reproduce the flame speeds, temperatures, and concentrations of major and minor species at high pressure.

• Journal of the Korea Convergence Society
• /
• v.9 no.10
• /
• pp.265-270
• /
• 2018

In this study, the flow analysis due to the car body configuration of air breather was carried out. As the resistance force whose flow affects car body has been studied, it is published that the electricity can be decreased. When the inner pressure of air breather is evaluated, there is the study of efficiency in order to raise the flow rate of inner body. At a total of five models, it is shown that the air resistance and pressure happen differently and the air pressure of side flow is changed. This study result was analyzed by using the analysis program of ANSYS, a study model was modelled using the CATIA V5 modelling program. It was investigated that the air flow rate was distributed uniformly as the curved surface of air breather configuration increases. It is thought as the most effective design method to design the air breather by considering the effect on the air resistance and flow. Also, through the design of the vehicle's airbrid configuration, the design of the product can incorporate a aesthetic sense into the design.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.2
• /
• pp.57-60
• /
• 2005

Semiconductor carbon nanotube was grown on oxided silicon wafer with atmosphere pressure chemical vapor deposition (APCVD) method and investigated the electrical property after thermal oxidation at $300^{\circ}C$ in air. The electrical property was measured at room temperature in air after thermal oxidation at $300^{\circ}C$ for various times in air. Semiconductor carbon nanotube was steadily changed to metallic carbon nanotube as increasing of thermal oxidation times at $300^{\circ}C$ in air. Some removed area of carbon nanotube surface was shown with transmission electron microscopy (TEM) after thermal oxidation for 6 hours at $300^{\circ}C$ in air.

• Journal of Chest Surgery
• /
• v.36 no.11
• /
• pp.834-838
• /
• 2003

Background: Deairing from the heart after open heart surgery(cardiopulmonary bypass) is a very important procedure. Artificial arteriovenous fistula was used to remove air, and the efficiency was evaluated by transesophageal echocardiography. Material and Method: Just before termination of cardiopulmonary bypass, a standard pressure transducer line is connected between the stopcocks of the connections in the arterial and venous circuits, creating a small controlled arteriovenous fistula between the arterial and venous cannulas. The degree of intracardiac air and air removal time were evaluated either by transesophageal echocardiography or direct vision of pressure transducer line. Result: By simple procedure, cardiopulmonary time was shortened and air clearing can be confirmed using echocardiography in a few minutes. Conclusion: Creation of arteriovenous fistula using small connecting line between aortic and venous cannula is a very simple and effective method of deairing and preventing of air embolism after open heart surgery.

• Tribology and Lubricants
• /
• v.22 no.2
• /
• pp.93-98
• /
• 2006

The numerical analysis of the negative pressure porous gas bearings is presented. The pressure distribution is calculated using the finite difference method. The Reynolds equation and Darcy's equation are solved simultaneously. The air bearing stiffness and damping are evaluated using the perturbation method. Rectangular uniform grid is employed to model the bearing. The vacuum preloading is considered. The pressure in the vacuum pocket is assumed to be a constant negative pressure. The total load, stiffness, damping and flow rate are calculated fur several geometrical configurations and several values of negative pressure. It is found that too large vacuum pocket can result in negative total force.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.24-27
• /
• 2002

The environmental problems by using coolant demanded the new cooling methods. As one of them, the studies on the finding with compressed cold air and oil mist have been done. The cooling method using compressed cold air was effective through going down the temperature of compressed air supplied below $-25^{\circ}$ and increasing the amount of compressed cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using oil mist newly were suggested. This method can satisfy both cooling effect and lubrication with only small amount of coolant, also have the benefit in the point of decreasing the environmental pollution. This paper focused on analyzing the grinding characteristics of the cooling method using oil mist. The grinding test according to compressed cold air, oil mist spray pressure and oil mist supply direction were done.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.67-74
• /
• 2001

A synchronized secondaty air injection method has been developed to hydrocarbon emission by injecting secondary air intermittently into exhaust port. The method has been tested in a single cylinder spark-ignition engine operating at cold-steady / cold-start conditions. Effects of air injection timing, intake pressure and engine air-fuel ratio have been investigated at cold-steady condition. Also, hydrocarbon emission and exhaust gas temperature with catalytic conberter are compared with a continuous SAI method and base condition at cold-start condition. Resules show that hydrocarbon reduction rate and exhaust gas temperature are sensitive to the timing of synchronized SAI. At cold-steady condition, HC emission is minimum at engine air-fuel ratio of 10. At cold-start condition, the accumulated hydrocarbon emission during the first 120 s decreases about 56% and 22% with the synchronized and continuous SAI, respectively, compared to that of base condition.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.11
• /
• pp.1020-1030
• /
• 2000

A crossflow finned tube evaporator has been investigated using tube-by-tube method. The refrigerant flows inside tubes while the air passes outside the finned tue. R134a for a refrigerant and wet air were used in this analysis. Three refrigerant circuitries, complex or simple, were compared. The effects of refrigerant circuitry and airside condensation on thermal performance such as heat transfer rate, enthalpy of refrigerant, temperature of refrigerant and air, pressure of refrigerant and average condensate layer thickness were investigated. It was found that this method could be applied to the analysis of finned tube evaporator for dehumidification and air conditioning.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1211-1221
• /
• 1990

The purpose of this study is to get experimental data on the distribution of CWM (Coal- Water Mixture) droplets size and the presence of pulverized coal particles inside CWM droplets. Atomization of CWM is done by Twin-Fluid Atomizer. The operational parameters are atomizing air pressure, coal particle loading, mean size of pulverized coal particles and sampling positions across spray. Th data analysis is initiated by Impression Sampling Method(Magnesium Oxide Technique) and Photo-technique and counting works are followed. Experimental work induces following research results. The variation of particle loadings in slurry makes no appreciable effects on the mean size of CWM droplets. It is evident that atomizing air pressure has very strong effect on the atomization of slurry. The mean size of atomized fuel droplets is dramatically reduced with the increasing air pressure. The population ratio of droplets without coal particles to total number of droplets is decreased as atomizing air pressure or loading rises and the same trend is obtained as the mean size of coal particles becomes smaller but a certain tendency of coal particle presence inside droplets could not be found from the change of sampling positions.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.65 no.1
• /
• pp.61-72
• /
• 2023

The increase in the rearing intensity of pigs has caused deterioration in the pig house's internal environment such as temperature, humidity, ammonia gas, and so on. Traditionally, the widely used method to control the internal environment was through the manipulation of the ventilation system. However, the conventional ventilation system had a limitation to control the internal environment, prevent livestock disease, save energy, and reduce odor emission. To overcome this problem, the air-recirculated ventilation system was suggested. This system has a semi-closed loop ventilation type. For designing this system, it was essential to evaluate the ventilation rates considering the pressure loss of ducts. Therefore, in this study, pressure loss calculation and experiment were conducted for the quantitative ventilation design of a semi-closed loop system. The results of the experiment showed that the inlet through which external air flows should always be opened. In addition, it was also found that for the optimum design of the semi-closed loop ventilation system, it was appropriate to install a damper or a backflow prevention device rather than a ventilation fan.