• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.17-22
• /
• 2014

Recently, the quick heating performance is an important issue in the car because engine power becomes so high. So car makers have been adapted the additional heating devices as like PTC(Positive Temperature Coefficient) heater. And the quick cooling performance is also important issue because its result is used in the IQS(Initial Quality Study). In this paper, control of the HVAC(Heating, Ventilation and Air Conditioning) intake door has been studied for the quick heating and cooling performance. Heating performance is improved $4.0^{\circ}C$ at $-20^{\circ}C$ ambient temperature after 20 minutes. And cooling performance is improved $1.5^{\circ}C$ at $35^{\circ}C$ ambient temperature after 10 minutes. In addition, intake door control system brings on the cost reduction because the flab door can be eliminated. This intake door control system has been adapted to the new developing cars.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.1-8
• /
• 2002

The flow and combustion patterns have been investigated inside the gasoline engine cylinder with the swirl or tumble flow, whereas the air flow characteristics, which are generated in the part of intake system before entering into the intake manifold, have not been known completely. It is necessary to analyze the flow field in the intake system consisting of air rater, throttle valve and intake manifold. The throttle valve, used to control the intake air flow rate, is important because it makes various mass flow rate and flow patterns. Three-dimen-sional How characteristics such as velocities, turbulent intensities and Reynolds shear stresses are measured by the hot wire anemometer at the exit of the throttle valve with the variation in the valve opening angle($15^{\circ}$, $45^{\circ}$, $75^{\circ}$ and $90^{\circ}$) and the Reynolds numbers (45000, 70000 and 140000). There are a lot of changes in flow characteristics at $75^{\circ}$ due to the large recirculation flow comparing with those of the other cases, and the streamwise velocity is especially enforced strongly below the valve shaft. The other component velocities are relatively large near the centerline parallel to the valve shaft. The effects of the Reynolds number on the flow field are not severe.

• 동력기계공학회지
• /
• 제19권2호
• /
• pp.64-69
• /
• 2015

Marine diesel engines with high thermal efficiency and fuel diversity used for propulsive power have been taking charge of important position on marine transport. However, marine environment has recently focused on emissions such as nitrogen oxide and sulfur oxide which is generated from combustion of low grade fuels. EGR(Exhaust gas recirculation) system is one of effective methods to reduce the nitrogen oxide emission from marine diesel engines. In general, it is considered that recirculating gas influences fuel combustion and emissions in diesel engines. However, along with positive effects of EGR, the EGR system using fuels of including high sulfur concentration should be considered about re-combustion and activation of sulfur dioxide in recirculating gas. Therefore, in experimental study, an author investigates effects of sulfur dioxide mixture concentration in intake air on combustion and exhaust emission characteristics in a direct injection diesel engine. In results, change of sulfur dioxide concentrations in intake air had negligible impact on combustion chamber pressure, rate of heat release and emissions compared with effects of oxygen decreasing and carbon dioxide increasing of EGR.

• 한국항공우주학회지
• /
• 제41권9호
• /
• pp.714-719
• /
• 2013

본 연구 대상 터보 프롭 항공기는 주어진 항공기 임무 수행을 위해 결빙 조건하에서도 운용이 가능하여야 한다. 동 연구에 적용된 터보 항공기의 공기 흡입구 계통은 정상 비행조건하에서 엔진 입구에 최대 전압력을 공급할 수 있도록 설계 및 검증이 되어야 할 뿐만 아니라 결빙조건하에서 생길 수 있는 얼음과 같은 입자가 엔진 흡입구 망으로 들어가서 엔진 화염꺼짐이나 엔진에 심각한 손상을 주지 않도록 하기 위한 관성분리기를 포함하도록 개발이 되어야 한다. 따라서 결빙 조건하에서 형상이 변하는 가변형상의 공기흡입구 조립체를 설계하고 설계 결과 확인을 위해 조립체에 대한 전산 유동 및 구조해석을 수행하였다. 이후 35% 축소형 모델을 제작하여 풍동시험을 수행하였다. 동 논문에서는 흡입구 조립체 개발과정에서 요구되는 공기역학적 설계, 잔산 유동/구조 해석 및 풍동 시험평가 결과를 기술하였다.

• Architectural research
• /
• 제19권4호
• /
• pp.101-108
• /
• 2017

The use of the air conditioner is increasing due to the rise of the outdoor temperature during summer, and the problems of the fire and the cooling performance deterioration are caused due to lack of maintenance of the outdoor unit. In particular, overall performance of cooling system and efficiency in outdoor units have been degraded due to an intake of high-temperature outdoor air thereby increasing cooling energy and operating cost. Thus, this study aimed to increase efficiency of outdoor units by evaporating and cooling intake air through mist spray at the intake port surface in the outdoor unit. The measurements results showed that total power consumption of misting outdoor unit compared to that of conventional outdoor units was reduced by 21% approximately, and total power consumption of the entire system including pump was reduced by 16.7%. In addition, the operating cost including water use was reduced by 13.5% approximately. In summary, if a mist-spray nozzle kit is installed in air-cooled outdoor units, the reduction in the usage of cooling energy and operating cost will be achieved without replacement of existing cooling systems or a large scale of repairs.

• 한국유체기계학회 논문집
• /
• 제20권1호
• /
• pp.74-80
• /
• 2017

Pump sump system or pumping stations are built to draw water from a source such as river and used for irrigation, thermal power plants etc. If pump sump is improperly shaped or sized, air entraining vortices or submerged vortices may develop. This may greatly affect pump operation if vortices grow to an appreciable extent. Moreover, the noise and vibration of the pump can be increased by the remaining of vortices in the pump flow passage. Therefore, the vortices in the pump flow passage have to be reduced for a good performance of pump sump station. In this study, the effect of pump intake leaning angle and flow rate on the pump sump internal flow has been investigated. There are three cases with different leaning angle. Moreover, a pipe type with elbow also has been studied. The flow rate with three classes of air entraining vortices has been examined and investigated by decreasing the water level. The result shows that the air entraining vortices easily occurs at the pump intake with large leaning angle. Moreover, the elbow type of the pump intake easily occurs air entraining vortices at the high flow rate (or velocity) in comparison to other pump intake type.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.480-485
• /
• 2008

In this study, two types of ramjet intake were designed for the flight condition of Mach number 2 and 5 and numerical analysis was performed. In order to widen the flight envelope range(Mach number $2{\sim}6$), movable intake concept was applied. The central body was designed so that the capture area ratio which is one of most important factors of ramjet intake design could be adjusted. And various types of cowl and movable insert part of shell were designed in order to control throat area which could increase total pressure recovery. The numerical results showed that the designed ramjet intake could be applied in various flights Mach number.

• 대한기계학회논문집B
• /
• 제26권12호
• /
• pp.1756-1762
• /
• 2002

To effectively meet current regulations on the exhaust emissions of diesel engine required to control the deterioration of air pollution in the whole world, this study is to investigate the effects of water induction through the air intake system on the characteristics of combustion and exhaust emissions in IDI diesel engine. A method fur supplying water through the air intake system to reduce the exhaust emissions has been considered with other methods such as water introduction in the form of water-in-fuel emulsion or water injection directly into the combustion chamber, but it has not been studied about the effects of water on the combustion concepts and the characteristics of exhaust emissions in detail until now. In this study, the formation of NOx was significantly suppressed by decreasing the gas peak temperature during the initial combustion process because the water play a role as a heat sink during evaporating in the combustion chamber, but the smoke was slightly increased by increasing water amount.

• 대한기계학회논문집
• /
• 제18권12호
• /
• pp.3315-3325
• /
• 1994

To study the variation of charging efficiency in the engine intake, the method to change the natural frequency of intake system using the intake control valve was studied and it has been used in actual engine to increase the intake air. In this paper, the method of characteristics was used to analyze the non-steady state and compared with the experimental data of the 6-cylinder diesel engine showing the effectiveness of the method theoretically.

• Journal of Radiation Protection and Research
• /
• 제38권4호
• /
• pp.234-236
• /
• 2013

비밀봉 방사성물질을 취급하는 시설에서 이들 물질에 의한 작업환경의 다소간의 오염은 피할 수 없다. 오염의 우려가 있는 작업환경에서 오염관리의 일차적인 목적은 방사성물질의 잠재적 체내섭취로 인한 영향이다. 본 논문은 보수적 가정과 간단한 계산에 의거하여 공기오염에 따른 방사성물질의 공기중 농도와 흡입에 의한 연간 섭취량을 산출한 후, 관련 고시에서 정하는 유도공기중농도와 연간섭취한도와 비교함으로써 종사자의 내부피폭 정도를 평가하는 절차를 제공한다. 제시된 절차는 공기중 방사성물질 측정 및 내부피폭 감시의 필요성, 적합한 방호용구의 착용, 배기설비 설계를 위한 정보 획득 등 공기오염과 종사자의 내부피폭 감시를 위한 실무적 요건을 판단할 목적으로 활용될 수 있다.