• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.82-87
• /
• 2012

Research and development of the spinning system which become bigger, faster and more detailed has been making progress continuously due to the increasing use of yarn which is considered as raw material to make industrial goods such as tire cord, air bag, filter, seatbelt and fiber-optic cable along with a remarkable growth of industry. In this paper, the desirable procedure and design requirements concerning a method of vibration reduction for "Godet Roller" considered as the main source of high vibration in the spinning system were suggested, and then verified those by analysis and actual test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.412-415
• /
• 2003

[ $Si_3N_4$ ] thin film is the good material to fabricate the capacitors at MMIC processes. Normally, $Si_3N_4$ thin films is used to dielectric in the MIM capacitor and film thickness is $2000\;{\AA}$. Insulator(or dielectric) was deposited by PECVD at our MIM structure with air bridge which connect between top metal and contact pad. We optimized PECVD process to fabricate the good capacitors which can be applied at the true MMIC. The thickness of our $Si_3N_4$ thin films was $1000\;{\AA}$ shallower than $2000\;{\AA}$, and their breakdown voltages were above 70V.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.176-181
• /
• 2001

Reflow soldering characteristics of Sn-3.5Ag and Sn-37Pb balls for BGA(Ball grid Array) were investigated. Diameter of 0.76mm ball was set on a Cu/Ni/Au-coated pad and reflowed in air with changing peak soldering temperature and conveyor speed. Peak temperatures were changed from 240 to 28$0^{\circ}C$ for Sn-3.5Ag, and from 220 to 26$0^{\circ}C$ for Sn-37Pb balls. As results, heights of solder balls increased and widths decreased with peak soldering temperature. Through aging treatment at 10$0^{\circ}C$ for 1.000 hrs, average hardness of Sn-3.5Ag balls bonded at 25$0^{\circ}C$ cecreased from 14.90Hv to 12.83Hv And with same aging conditions, average shear strength of Sn-3.5Ag balls bonded at 26$0^{\circ}C$ decreased from 1727gf to 1650gf.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.59-60
• /
• 2015

Wireless power transfer is a technique that supplies the necessary power to the various electronic devices over the air without wires. The technology is classified as near-field wireless power transfer technology using inductive coupling and far-field wireless power transfer technology using antenna. In this paper, RTLS tag for high-precision positioning and wireless power transfer module was designed in order to solve the power supply problem for facility management. was designed for high-precision positioning is possible RTLS tags and wireless charging. The wireless charging pad provides the capability to charge up to four devices using he magnetic resonance system.

• Textile Coloration and Finishing
• /
• v.10 no.3
• /
• pp.50-56
• /
• 1998

Nonwoven fabric was treated with chitosan solution to impart antimicrobial activities by pad-dry method. Antimicrobial activity was measured by Shake Flask Method. Two chitosans of different molecular weight(Mw) with similar degree of deacetylation(DDA) were used : ca. 1,800(chitosan oligomer : DDA 84%) and 180,000(DDA 86%). Chitosan oligomer displayed high antimicrobial activity against P. vulgaris at 0.01%, S. aureus and E. coli at 0.05% treatment concentration, shelving above 90% of reduction rate. Chitosan of Mw 180,000 was effective against S. aureus, E. coil and P. vulgaris at 0.05% treatment concentration, showing almost 100% reduction rate. While chitosan of Mw 180,000 shelved reduction rate above 75% against K. pneumoniae and P. aeruginosa at 0.5% treatment concentration, chitosan oligomer was not effective against them. Fabrics become stiffer and less air permeable as treatment concentration increases. Liquid strike-through time of the sample treated with 0.5% chitosan oligomer solution (3.0 sec) was comparable with a hydrophilic finished sample commercially available(2.6 sec).

• Restorative Dentistry and Endodontics
• /
• v.4 no.1
• /
• pp.29-34
• /
• 1978

The purpose of this study was to measure penetration of dye stuff(5% Methylene blue, Hematoxylin, Crystal violet and Safranin-O) on silicate cement, Adaptic, Hi-pol and unfilled resin. Each filling material was mixed on the mixing pad and the mixed material was inserted with condensation force of 500gr, 1000gr and 2000gr and without condensation force into preformed glass tube (10mm in diameter and 10mm in height). The specimen was stored in the air for 24 hours, then specimen was immersed in various dye solution (5% methylene blue, hematoxin, crystal violet and safranin-O) for different period of time (l hour and 24 hours). These dye-treated specimen was cut horizontally at the middle portion and the dye penetration in cut surface was measured. Following results were obtained. 1. Pentration of various dye was excessive in silicate cement with and without Condensation force. 2. There has been no evidence of dye penetration in unfilled resin. 3. Dye penetration occurced with in 1 hour period and the extending time didn't affect the dye penetration.

• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.312-320
• /
• 2001

In magnetic hard disk drives, higher areal recording density requires reduction of head-disk spacing. To overcome the increase of stiction associated with reduction of head-disk spacing, a padder slider, which adds pads to slider's air bearing surface, can be one of the practical solution for sub 20 nm flying height, and even for near contact recording. This study investigated the tribological characteristics of a padder slider. A padder slider took off slowly but showed less friction force than a normal slider. The hot/dry CSS test and drag test indicated that pad wear of a padder slider was negligible. The tribological performance of disk is an important factor to be considered. In particular, less carbon overcoat layer of the disk will result in higher stiction and wear in slider/disk interface. In conclusion, a padder slider shows encouraging tribological performances for practical use in HDD.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.543-544
• /
• 2014

In this paper, we present the design of a compound sensing platform to share environment information with other smart devices such as a gateway, a phone, a pad, etc. The proposed compound sensing platform is designed as a single-board hardware to support air temperature and humidity, soil temperature and humidity, solar visible radiation, etc. It sends the measured information to a smart gateway which shares the information with smart phones and pads by Twitter.

• Journal of Bio-Environment Control
• /
• v.9 no.4
• /
• pp.201-206
• /
• 2000

A certain system to overcome high temperature should be introduced for the stable year-round cultivation in greenhouses. There are efficient methods to overcome high temperature such as ventilation system with shading screen, fan and pad system with screen, and fog system with screen. This study was carried out to find a means to determine the capacity of such system. Heat balance equations for each system were established and verified by experimental results. The calculated ventilation rates from heat balance equations showed a good agreement with the measured ones. The evapotranspiration coefficient was the most important parameter affecting the ventilation requirement among input parameter affecting the ventilation requirement among input parameters except weather data. When the evaportanspiration coefficient increased 1%, the ventilation requirement decreased 1.3%. Therefore the data of evapotranspiration coefficient should be accumulated by various experiments, and then design standards and selection guidelines should be provided. The simulation results for same design conditions shown that air exchanges requirement and evaporating water of fan and pad system were 5.1∼7.7% and 6.8∼9.3% larger than those of fog system, respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1149-1156
• /
• 2008

The principle of self clamping friction clutch is presented in this paper and the transmitted torque capacity is also calculated. In order to enlarge the friction force, a part of rotating force of driving side is converted to normal force of friction materials by clamping arm. The increased normal force of friction materials assures the large friction force and the transmitted torque capacity of clutch becomes large. The self clamping friction clutch is adopted in the tube type air pressure clutch and the condition of stability is investigated. It is proven that the inclined angle of clamping arm and the friction factor of friction materials are the essential elements in stability and torque capacity of self clamping friction clutch. The transmitted torque capacity of self clamping friction clutch is compared with air pressure clutch. The normal force of friction lining is magnified by 1/(1-k) and the transmitted torque capacity is also magnified with same proportion comparing with air pressure clutch. The larger the friction factor of friction lining, the larger the magnification factor. The longer the clamping arm, the smaller the magnification factor. It must be also noted that the value of k=${\mu}Y/X$ is the criterion of stability. If the value of k=${\mu}Y/X$ is greater than or equal to 1, the self clamping friction clutch is unstable and it can not be used as clutch.