• 한국유체기계학회 논문집
• /
• 제16권1호
• /
• pp.5-10
• /
• 2013

The performance of screw air compressor is affected by rotor profile, lobe number, air end wrap angle, rotor L/D ratio, suction and discharge ports, revolutions of air end and load regulation control, etc. In general, an efficient screw compressor needs a rotor profile of which has a large flow cross-section area, short sealing lines and a small blow-hole. In this study, experimental study was performed with newly designed $5{\times}6$ rotor profile and various shapes of air end. Results show that the measured specific power consumption of the newly designed screw compressor appeared to be lower than any other published data for the equivalent screw compressors manufactured.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.9-18
• /
• 1998

The vortex tube is a simple device for separating a compressed gaseous fluid stream into two flows of high and low temperature without any chemical reactions. Recently, vortex tube is widely used to local cooler of industrial equipments and air supply system. The phenomena of energy separation through the vortex tube was investigated experimentally. This study is focused on the effect of the diameter of cold end orifice diameter on the energy separation. The experiment was carried out with various cold end orifice diameter ratio from 0.22 to 0.78 for different input pressure and cold air flow ratio. The experimental results were indicated that there are an optimum diameter of cold end orifice for the best cooling performance. The maximum cold air temperature difference was appeared when the diameter ratio of the cold end orifice was 0.5. The maximum cooling capacity was obtained when the diameter ratio of the cold end orifice was 0.6 and cold air flow ratio was 0.7.

• Fibers and Polymers
• /
• 제6권3호
• /
• pp.250-258
• /
• 2005

The present paper is concerned with the influence of opening roller speed, drum speed difference and suction air pressure on properties of polyester and acrylic open-end friction spun yams. The results shows that the opening roller speed and the suction air pressure have considerable influence on the characteristics of polyester and acrylic open-end friction spun yams. In case of polyester yams the unevenness, imperfection and hairiness decreases and the yam tenacity increases with the increase in opening roller speed and suction air pressure. However for acrylic yams the unevenness and imperfections decreases and tenacity increases with the increase in opening roller speed and suction air pressure.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.352-357
• /
• 2016

More recently, workers and passengers of casualties has increased by rear-end collisions of unexpected while working on the road. Recently attracted air chamber TMA mounting car accidents which occurred in 3 years, and analyzed the effect of reducing the shock absorption and protection performance and casualties. There is a risk of the vehicle AIS4 more injury of high five accidents of casualties risk, also, was the analysis that there is risk of death was avoided by the air chamber TMA and SGT. Therefore, by mounting the TMA in the rear-end accident, so you can reduce the death and casualties, it must be increased this of attach rate for road construction vehicle.

• Tribology and Lubricants
• /
• 제22권5호
• /
• pp.252-259
• /
• 2006

Air foil bearing supports the rotating journal using hydrodynamic force generated at thin air film. The bearing performances, stiffness, damping coefficient and load capacity, depend on the rotating speed and the performance of the elastic foundation, bump foil. The main focus of this study is to decide the dynamic performance of corrugated bump foil, structural stiffness and Coulomb damping caused by friction between bump foil and top foil/bump foil and housing. Structural stiffness is determined by the bump shape (bump height, pitch and bump thickness), dry-friction, and interacting force filed up to fixed end. So, the change of the characteristics was considered as the parameters change. The air foil bearing specification for analysis follows the general size; diameter 38.1 mm and length 38.1 mm (L/D=1.0). The results show that the stiffness at the fixed end is more than the stiffness at the free end, Coulomb damping is more at the fixed end due to the small displacement, and two dynamic characteristics are dependent on each other.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1135-1141
• /
• 2006

Air foil bearing supports the rotating journal using hydrodynamic force generated at thin air film. The bearing performance, stiffness, damping coefficient and load capacity, depends on the rotating speed and the performance of the elastic foundation, bump foil. The main focus of this study is to decide the dynamic performance of corrugated bump foil, structural stiffness and Coulomb damping caused by friction between bump foil and top foil/bump foil and housing. Structural stiffness is determined by the bump shape (bump height, pitch and bump thickness), dry-friction, and interacting force filed up to fixed end. So, the change of the characteristics was considered as the parameters change. The air foil bearing specification for analysis follows the general size; diameter 38.1 mm and length 38.1mm (L/D=1.0). The results show that the stiffness at the fixed end is more than the stiffness at the free end, Coulomb damping is more at the fixed end due to the small displacement, and two dynamic characteristics are dependent on each other.

• Corrosion Science and Technology
• /
• 제19권4호
• /
• pp.189-195
• /
• 2020

Two air vents situated on a heat transport pipe in district heating system were exposed to the same environment for 10 years. However, one air vent was more corroded than the other. It also had a hole on the top of the front-end pipe. Comparative analysis was performed for these air vents to identify the cause of corrosion and establish countermeasures. Through experimental observation of the damaged part and analyses of powders sampled from air vents, it was found that corrosion was initiated at the top of the front-end pipe. It then spread to the bottom. Energy dispersive X-ray spectroscopy results showed that potassium and chlorine were measured from the corroded product in the damaged air vent derived from rainwater and insulation, respectively. The temperature of the damaged air vent was maintained at 75 ~ 120 ℃ by heating water. Rainwater-soaked insulation around the front-end pipe had been hydrolyzed. Therefore, the damaged air vent was exposed to an environment in which corrosion under insulation could be facilitated. In addition, ion chromatography and inductively coupled plasma measurements indicated that the matrix of the damaged front-end pipe contained a higher manganese content which might have promoted corrosion under insulation.

• 국제학술발표논문집
• /
• The 6th International Conference on Construction Engineering and Project Management
• /
• pp.740-741
• /
• 2015

the downscaled air temperature data over study region for the projected 2001 - 2099 period were then ensemble averaged, and the ensemble averages of 6 realizations were compared against the corresponding historical downscaled data for the 1961 - 2000 period in order to assess the impact of climate change on air temperature over study region by graphical, spatial and statistical methods. In order to evaluate the seasonal trends under future climate change conditions, the simulated annual, annual DJF (December-January-February), and annual JJA (June-July-August) mean air temperature for 5 watersheds during historical and future periods were evaluated. From the results, it is clear that there is a rising trend in the projected air temperature and future air temperature would be warmer by about 3 degrees Celsius toward the end of 21^st century if the ensemble projections of air temperature become true. Spatial comparison of 30-year average annual mean air temperature between historical period (1970 - 1999) and ensemble average of 6-realization shows that air temperature is warmer toward end of 21^st century compared to historical period.

• 대한전기학회논문지
• /
• 제36권4호
• /
• pp.240-251
• /
• 1987

In this paper, with the end effect taken into consideration, the fundamental characteristics of a linear induction motor-the eddy currents of the secondary conducting sheet (traveller), the flux density in the air gap-are analysed by means of electromagnetic field theory. Accordingly, the derived governing eqations of the chatacteristics with goodness factor, presents that it was possible not only to predict the performance characteristics, but to obtain the data that needs to optimize a design of a motor with the reduction of the end effect.

• 생물환경조절학회지
• /
• 제3권1호
• /
• pp.36-41
• /
• 1994

본 시험의 목적은 온실의 주년계획이용을 위해서 하기주간 냉방의 방법으로 heat pump를 이용한 냉수냉방과세무냉방의 효율성을 검사했고 하기 토마토 배꼽썩음병 발생을 억제하기 위하여 냉방과 함께 과실에 송풍처리와 식물체 전체의 공기유동을 촉진시켜주는 처리를 했다. 시험결과는 다음과 같다. 1) 냉수냉방구간 기온은 13시경 온실내 기온보다 약 1$0^{\circ}C$이상 낮았고, 세무냉방구간 하부의 기온은 13시경 온실내 기온보다 약 5$^{\circ}C$ 낮았다. 2) 과실에 송풍처리는 냉방방법에 상관없이 배꼽썩음병이 방지됐고, 냉수냉방 무송풍구의 배꼽썩음병 발생율은 34.5%, 세무냉방 무송풍구는 54.5%, 세무순환냉방구는 78%였다. 냉방효율면에서는 냉수냉방 방법이 충분히 생육한계온도 이하로 냉각되었고, 배꼽썩음병 발생율에서도 세무냉방보다 낮았다. 세무냉방은 재배구간의 공기를 유동시킴으로서 약 24%증가했다. 그러므로 토마토 배꼽썩음병 발생에 관한 환경요인은 온도보다는 습도가 밀접한 관계가 있는 것으로 생각되어진다.