• Journal of the Korean Society of Industry Convergence
• /
• v.12 no.3
• /
• pp.129-135
• /
• 2009

This paper describes traveling systems consisting of one major-wheel and three minor-wheels attached to each tip of three spokes. A link of inter-axle plays an important role of the system. It connects secondary axle to the major wheel axle. Its length is determined to ascend stably various stairs. The systems was designed to mount a cart for carrying agricultural products. The systems was applied to ascend stairs, travel on sand and cross a obstacle, despite of simple design.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.7 no.1
• /
• pp.21-24
• /
• 2001

This study was carried out to analyze the effects of packaging units and loading types in agricultural products(apple, pear, and sweet persimmon) palletization. In apple and pear packaging, an optimum loading type was pin wheel loading, and load effective corrugated box dimension was $330{\times}220{\times}170mmm(L{\times}W{\times}H)$ in 5 and 10kg packaging units, but in case of pear box was 10mm higher than apple box. However, in sweet persimmon packaging, block loading was available, and box dimension of $365{\times}275{\times}180mm(L{\times}W{\times}H)$ was the most effective to palletize.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.31-48
• /
• 1993

Economic background is discussed with consequences for tractor industry and tractor concepts. Particular reference is given to the question of frame chassis instead of block concept. Development trends of tractor components are analyzed for driving system (including four-wheel drive and brakes), diesel engines, transmissions, human engineering , hydraulics and implement control. Consideration is given to electronics and aspects of environmental protection as well. Expected further tractor design developments are summarized at the end of the paper.

• Journal of Biosystems Engineering
• /
• v.21 no.4
• /
• pp.399-405
• /
• 1996

In order to maintain a constant speed ratio between the tractor and attached seed planter, a feedback control unit to rotate the feed shaft of the planter in proportional to the ground speed of the tractor was designed. The fifth wheel was used as a ground speed sensor for the unit. Using this control unit a feed shaft driving system was developed and tested to estimate its performance both in laboratory and fields. The test results showed that the system rotates the feed shaft proportionally to the ground speed in the range of the normal planting speed of 0.5-0.8m/s with errors less than 5%.

• Journal of Biosystems Engineering
• /
• v.14 no.3
• /
• pp.158-167
• /
• 1989

This study was conducted to investigate the applicability of true model theory in a powered lugged wheel-soil system and to examine the possibility of using principles of similitude in investigating the dimensions of soil parameters pertinent to a powered lugged wheel-soil system concerning the sinkage prediction. The following conclusions were derived from the study; 1) The sinkage of prototype wheels proved to be predicted by those of the model wheels for the range of the dynamic weight tested. 2) A conditional equation which can be used for the prediction of sinkage of prototype by model test was derived as $n_f=n{_\ell}{^{-b}}$. The range of the numerical value of b, which is the exponent on the length dimension of the soil property ${\alpha}$, was found to be -1.48~-2.54. 3) Considering a relatively wide variation of b values, it was concluded that there are several soil properties which are pertinent to the powered lugged-wheel soil system concerning the sinkage prediction.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.1125-1131
• /
• 2012

According to abrupt decrese in number of farmer and ageing society, there has been a need for development of low cost agricultural robot. In this paper, a H/W and S/W platform of caterpillar type agricultural chemical dusting robot based on XP embedded system were described. The developed agricultural robot has 2 d.o.f caterpillar type driving wheel and 2 d.o.f chemical dusting spray mechanical system. The H/W platform of the agricultural robot consists of robot controller, remote controller and sensor controller. In S/W platform, 5 processes work concurrently, which are task manager, TCP-IP communication process, localization process, wheel control, and sensor control process. This robot platform has been developed for chemical dusting robot. We proved this system's validity through field test.

• Journal of Biosystems Engineering
• /
• v.33 no.4
• /
• pp.217-223
• /
• 2008

In this study, a garlic clove planter which is capable of planting holes in soil and planting a clove at the same time was designed and tested for film mulched beds. Planting characteristics of the planter were measured through field experiment. Some characteristics were analyzed with multibody dynamic simulation software. Simulation was performed on opening time of the planting hopper. Measured characteristics were position, angle, and reposition amount of garlic in sowing hole. Experiment results showed that the planted position of garlic in planting was 23.0 mm from the hole wall. The reposition amount of garlic was varied with its position and angle when the planted garlic was pressed by an angled compaction wheel. In case of type II position, the position movement of garlic was larger than type I. Average position movement of type II was 11.5 mm at $20^{\circ}$ of compaction wheel angle. These data suggest that cutting diameter of film opening must be larger than 33 mm to provide enough space for garlic sprouting. Also, simulation results showed that the maximum opening time of the planting hopper was 0.26 second.

• Korean Journal of Agricultural Science
• /
• v.50 no.4
• /
• pp.773-784
• /
• 2023

In this study, we developed a dynamic model and steering controller model for an autonomous tractor and evaluated their performance. The traction force was measured using a 6-component load cell, and the rotational speed of the wheels was monitored using proximity sensors installed on the axles. Torque sensors were employed to measure the axle torque. The PI (proportional integral) controller's coefficients were determined using the trial-error method. The coefficient of the P varied in the range of 0.1 - 0.5 and the I coefficient was determined in 3 increments of 0.01, 0.05, and 0.1. To validate the simulation model, we conducted RMS (root mean square) comparisons between the measured data of axle torque and the simulation results. The performance of the steering controller model was evaluated by analyzing the damping ratio calculated with the first and second overshoots. The average front and rear axle torque ranged from 3.29 - 3.44 and 6.98 - 7.41 kNm, respectively. The average rotational speed of the wheel ranged from 29.21 - 30.55 rpm at the front, and from 21.46 - 21.63 rpm at the rear. The steering controller model exhibited the most stable control performance when the coefficients of P and I were set at 0.5 and 0.01, respectively. The RMS analysis of the axle torque results indicated that the left and right wheel errors were approximately 1.52% and 2.61% (at front) and 7.45% and 7.28% (at rear), respectively.

• Journal of Biosystems Engineering
• /
• v.30 no.2 s.109
• /
• pp.69-74
• /
• 2005

This study was carried out to investigate experimentally the effect of the ground condition and tire inflation pressure on rolling characteristics of towed wheel, including the deformation, sinkage, effective rolling radius and motion resistance of tire. The experiment was performed at soil bin for the three levels of off-road conditions(ground-I, ground-II and ground-III) and a on-road condition(ground-IV), and for the four levels of tire inflation pressure which were 80 kPa, 160 kPa, 240 kPa and 320 kPa. The results of this study are summarized as follows: 1. As the tire inflation pressure of towed wheel increased, the tire deformation decreased exponentially, but the tire sinkage increased exponentially. This trend was getting bigger as ground condition was getting softer. 2. The increase of tire inflation pressure increased the effective rolling radius of towed wheel, and this kind of trend occurred greatly as ground condition was soft. As a result, the effective rolling radius for the off-road condition was always larger than that for on-road condition. 3. For the on-road condition, as the tire inflation pressure of towed wheel increased, the motion resistance decreased, but for the off-road condition, augmentation of tire inflation pressure increased the motion resistance. Also, the effect of inflation pressure on motion resistance appeared great as ground condition was soft. Therefore, in order to improve the tire performance by the control of inflation pressure, it is desirable to reduce the tire inflation pressure for off-road condition and to increase the tire inflation pressure for on-road condition.

• Journal of Biosystems Engineering
• /
• v.5 no.2
• /
• pp.26-39
• /
• 1980

A study was investigated to find out the mechanical optimum conditions of power tiller-plow system on both paddy field and upland. Mathematical model was developed for the theoretical analysis of this system and the experimentation on the field was carried out with two different sizes of 5PS and 8PS power tiller equipped with rubber tire. 1) The relationship between the plowing depth and draft resistance of the power tiller-plow system was a quadratic function. 2) The minimum point of the specific draft resistance of the 5 PS plow was found at the smaller plowing depth than that of 8 PS plow, therefore we can find that the curved surface of 5PS plow bottom should be improved for the effective plowing operation. 3) As the improvement of the mechanical balance by the desirable change of the curved surface of plow bottom, the relative position of hitch point and dimension of plow beam would be realized, the 5 PS power tiller could be used to plow deeply (about 16-17cm). 4) The virtual acting point of the total draft resistance on the plow bottom approached to the land side as the plowing depth increased. 5) The resultant of vertical reaction force $R_2$ on the landside was increased with the plowing depth, while the vertical reaction force $R_1$ on the wheel was decreased as the slope angle of the body of power tiller increased. 6) For the effective plowing operations ; a) The slope angle of the body should be as small as possible. b) The diameter of the wheel should be as small possible. c) The horizontal and vertical distances $l_2, h_1$ between the wheel axis and plow bottom should be as large as possible. 7) To use the 5PS power tiller as the major unit of agricultural machinery, the curved surface of the 5 PS plower bottom and the mechanism of attachment between the power tiller and the plow should be changed as the indications of this study, and in addition to these, the new operation method of the field work should be developed.