• Journal of Bio-Environment Control
• /
• v.11 no.1
• /
• pp.5-11
• /
• 2002

In this study, new development of natural ventilation window was accomplished to control environment of greenhouse with no use of farced ventilation during hot season. The ventilation effect of developed ventilation window was investigated in experimental greenhouse which was designed using side wall panel and folding type panel fur natural ventilation. Folding panel type ventilation window was designed to open upper part of the side wall and top of the roof using two hinges which are located bottom of the side wall and the roof panel to grab one side of each panels and guide the other side along with the guidance rail. Developed ventilation window has top ventilation part with maximum moving distance X=ι (1-cos$\theta$)=848.5 mm and side ventilation part with maximum moving distance Y=ι/2 $\times$sin$\theta$=1,184.4 mm at 45$^{\circ}$ of theoretical opening angle. It took 4.5 minutes to open roof vent fully and temperature at 1.2 and 0.8 m height decreased after 1 minute from starting opening and became equilibrium state maintaining 3-4$^{\circ}C$ difference after 2 minutes from complete opening. Air exchange rate was 15.2~39.3 h$^{-1}$ which was more than 10~15 h$^{-1}$ of continuous type and Venlo type greenhouse. The descent effect of temperature by ventilation windows was two times higher than Venlo type greenhouse.

• Journal of Biosystems Engineering
• /
• v.5 no.1
• /
• pp.1-14
• /
• 1980

Threshing operation may be one of the most important processes in the paddy post-production system as far as the grain loss and labor requirement are concerned . head-feeding type threshers commercially available now in Korea originally were developed for threshing dry paddy in the range of 15 to 17 % in wet basis. However, threshing wet-paddy with the grain moisture content above 20 % has been strongly recommended, especially for new high-yielding Indica -type varieties ; (1) to reduce high grain loss incurred due to the handling operations, and (2) to prevent the quantitative and qualitative loss of milled -rice when unthreshed grains are rewetted due to the rainfall. The objective of this study were to investigate the adaptability of both a head-feeding type thresher and a throw-in type thresher to wet-paddy , and to find out the possiblilities of improving the components of these threshers threshing. Four varieties, Suweon 264 and Milyang 24 as Tongil sister line varieties, minehikari and Jinhueng as Japonica-type varieties, were used at the different levels of the moisture content of grains. Both the feed rate and the cylinder speed were varied for each material and each machine. The thresher output quality , composition of tailing return, and separating loss were analyzed from the sampels taken at each treatment. A separate experiment for measurement opf the power requirement of the head-feeding type thresher was also performed. The results are summarized as follows : 1. There was a difference in the thresher output quality between rice varieties. In case of wet-paddy threshing at 550 rpm , grains with branchlet and torn heads for the Suweon 264 were 12 % and 7 % of the total output in weight, respectively, and for the Minehikari 4.5 % and 2 % respectively. In case of dry paddy threshing , those for the Suweon 264 were 8 % and 5% , and for the Minehikari 4% and 1% respectively. However, those for the Milyang 23 , which is highly susceptable to shattering, were much lower with 1 % and 0.5% respectively, regardless of the moisture content of the paddy. Therefore, it is desirable to breed rice varieties of the same physical properties as well as to improve a thresher adaptable to all the varieties. Torn heads, which increased with the moisture content of rall the varieties except the Milyang 23 , decreased as the cylinder speed increased, but grains with branchlet didnt decrease. The damaged kernels increased with the cylinder speed. 3. The thresher output quality was not affected much by the feed rate. But grains with branchlet and torn heads increased slightly with the feed rate for the head-feeding type thresher since higher resistance lowered at the cylinder speed. 4. In order to reduce grains with branchlet and torn heads in wet-paddy threshing , it is desirable to improve the head-feeding type thresher by developing a new type of cylinder which to not give excess impact on kernels or a concave which has differenct sizes of holes at different locations along the cylinder. 5. For the head-feeding type thresher, there was a difference in separating loss between the varieties. At the cylinder speed of 600 rpm the separating losses for the Minehikari and the Suweon 264 were 1.2% and 0.6% respectively. The separating loss of the head-feeding type thresher was not affected by the moisture content of paddy while that of the Mini-aged thresher increased with the moisture content. 6. From the analysis of the tailings return , to appeared that the tailings return mechanism didn't function properly because lots of single grains and rubbishes were unnecessarily returned. 7. Adding a vibrating sieve to the head-feeding type thresher could increase the efficiency of separation. Consequently , the tailing return mechanism would function properly since unnecessary return could be educed greatly. 8. The power required for the head-feeding type thresher was not affected by the moisture content of paddy, but the average power increased linearly with the feed rate. The power also increased with the cylinder speed.

• Journal of Bio-Environment Control
• /
• v.23 no.3
• /
• pp.205-211
• /
• 2014

This study aimed to examine the effect of different fruit-loads on fruit yield, quality, and plant growth of 'Seolhyang' strawberry. Fruit loads were adjusted from the first to the fourth flower cluster so that the number of fruits became 20, 25, and 30, and non-flower thinning of some was made. The more the number of fruits per plant was, the greater the total yield obtained, but marketable yield decreased and non-marketable yield increased. Compared to the treatment whose fruit load was adjusted, the control with non-flower thinning had more fruit yield in the first and second flower clusters but tended to have less fruit yield in the third and fourth flower clusters. The lower the fruit load was, the more soluble solids content of fruits increased. The lower the fruit load of a flower cluster was, the faster its harvest time reached. Harvest of fruit load of 20 was faster by 10 days in the second and fourth flower clusters relative to the control. On November 24, 2012, flowering thinning of the first flower cluster was made. On March 7, 2013, fruit dry weight of the second flower cluster was most heavy in the control. Dry weight of roots decreased in the control and the fruit load of 30 compared to November 24. On April 9, fruit dry weight of the third flower cluster did not have significant difference according to fruit load, however the more the fruit load was, the smaller dry weight of leaf, root, and crown became, which were vegetative organs. On May 12, the more the fruit load, the smaller leaf area and dry weight of vegetative organs and differences from varying fruit-loads became considerable in later period of growth. Appropriate fruit load of 'Seolhyang' strawberry were from 20 to 25. Maintaining balance between vegetative and fruit growth by adjusting fruit load is very important for stable fruit production.

• Journal of Mushroom
• /
• v.12 no.3
• /
• pp.220-225
• /
• 2014

This study was conducted to set the proper sterilization standards of casing soil for the stable production of button mushroom(Agaricus bisporus) from mushroom disease that occurs in infection of casing soil material. Changes of aerobic bacteria are increased as the longer grow-out period and sharply increased after second flushes. Fluorescence Psuedomonas showed high density at high sterilization temperature and $100^{\circ}C$ treatment has extremely high density at 30 min and 60 min in casing 22 days. Density of thermophilic actinomyces is sharply increase from casing with soil and the highest density at 22 days of casing and rapidly decrease after first flushes. Sterilizing temperature of casing soil affects quality and quantity of button mushroom. Treatment of 60 min, 90 min at $80^{\circ}C$ and 30 min at $100^{\circ}C$ produced the highest mushroom yields, especially mushrooms yields of A grads were the highest at treatment of 90 min at $80^{\circ}C$. Treatment of 60min at $100^{\circ}C$ products many yields, however, this treatment has low economic feasibility for its yields. Sterilizing temperature of casing soil has an effect on generating diseases and insect pests. Treatment of 60 min, 90 min at $80^{\circ}C$ and 30 min $100^{\circ}C$ showed lower incidence than the other treatment. Although treatment of 30 min at $100^{\circ}C$ causes low diseases and mushroom fly damage, it has low mushroom yields. Furthermore, although treatment of 60 min at $100^{\circ}C$ has high mushroom yields, it causes high diseases and mushroom fly damage. Therefore the best conditions for the sterilization of casing soils was 60 min and 90 min at $80^{\circ}C$.

• Korean Journal of Organic Agriculture
• /
• v.26 no.2
• /
• pp.297-316
• /
• 2018

The golden apple snail (GAS, Pomacea canaliculata) is an invasive freshwater snail. The GAS was introduced in Korea without prior studies on the possibility of crop damage or its impact on the natural ecosystem. The freshwater apple snails can be found typically in ponds, rice paddies, irrigation canals, roadside ditches or slower portions of streams. In this study, we were carried out to investigate the assessment of physiological and ecological characteristics, environmental characteristics inhabited area in winter season and cause of massive death at one time of golden apple snails used for weed control in wet rice paddies. The GAS was introduced from Japan to Korea for commercial production as a dietary protein supplement. The golden apple snail was also used a recently for weed control in wet rice cultivation. The species of freshwater Pomacea snails is belonging to the genus Pomacea, family ampulariidae, order mesogastropoda, subclass pulmonata, class gastropoda, phylum mollusca. The GAS spread into irrigation ditches and natural waterways. It is now distributed in ponds and canals near rice fields of southern parts of the country and has overwintered. It increases its cold hardiness before winter. However, the physiological mechanism of cold hardiness in molluscs is poorly understood, especially in freshwater molluscs. Our results on physio-ecological characteristics of the Pomacea apple snail showed that the ratio of males to females was 1: 1.99~2.33. The daily growth was 87.7 mg in weight, 0.31 mm in height and 0.33 mm in width of the their shell. On the other hand, the golden apple snails were very high to resistance on drying condition and survived rate about 80% up to 3 months. The inhabitation of GAS was no statistical significant impacts on the water quality. An important property of aqueous solutions is agricultural water quality because it affects chemical and biochemical properties such as chemical reactions, equilibrium conditions, and biological toxicity. The death rate of weed control apple snails by Ostracoda (Stenocypris hislopi) was only 2.86% and 5.71% depending on the density. Therefore, GAS was not a direct death caused by Ostracoda (Stenocypris hislopi).

• Proceedings of the Technology Innovation Conference
• /
• 1997.07a
• /
• pp.222-223
• /
• 1997

By analyzing the successful innovation case of potato microtuber mass production technology, a representative case of technology-push type creative innovation in an imitation oriented research culture, this paper attempts to figure out conceptual model of creative innovation that is initiated by the public laboratories in catching-up country, Stages of creative innovation can be divided into the internal R&D stage and the external commercialization stage. Success of the internal R&D stage depended on autonomy to secure creative research idea and commitment of individual researchers. Psychological pressure evoked from sportlights of mass media and commitment of sponsor increased the intensity of research efforts of the researcher Recognition of research problem and its significance was intensified by site visits of agricultural fields, and the recognized higher impacts of expected research results and knowledge creation achieved were a fundamental source of self-motivation. In the stage of commercialization stage, various legal, socio-economic, and psychological barriers were confronted. In a catching-up country lacking of experiences of creative innovation, creative innovation process can be regarded as a barrier elimination and cultural revolution process. Among the barriers, psychological refusal of farmers to corn-sized potato seeds was critical, which finally enforced to further researches to enlarge the size of potato seeds. In addition, the researcher has concentrated his research efforts in one specialized research area by getting a series of similar research project funds rather than diversification. It was lucky for him to have a chance to carry out a series of similar researches in one research area during the last 10 years. In getting research funds from government and private companies continuously in one research area, both internal and external promoters played significant roles.

• Journal of Animal Science and Technology
• /
• v.55 no.1
• /
• pp.1-6
• /
• 2013

This study was aimed to solve the problems of current national genetic evaluation systems in Korea and its development to pass the verification processes as required by International Bull Evaluation Service (Interbull). This will enable Korea to participate in international genetic evaluation program. A total of 1,416,589 test-day milk records with calving dates used in this study were collected by National Agricultural Cooperative Federation from 2001 to 2009. Parity was limited up to fifth calving and milk production records were adjusted to cumulative 305 day lactation. The pedigree consisted of 2,279,741 animals where 2,467 bulls had 535,409 parents. A newly developed multiple trait model was used in calculation of breeding values for milk yield, milk fat, and protein yield. Data were edited with SAS (version 9.2) and R programs, and genetic parameters were estimated using VCE 6.0. Results showed a continuous increase in genetic potentials, in general, and no remarkable differences were found between performances by parity. Except fat yield, potentials in milk yield and protein yield were well calculated. We found an increased number of daughters per each top ranked 1,000 bulls in recent years of calf births compared to the cases of previous evaluations. Of the bulls ranked top 100 by our new models (multiple-trait models) we found that increased numbers of bulls were included. Of twenty eight bulls born in 2006, twenty bulls born in 2007 and eight bulls born in 2008 that were listed by new models, only 23, 12, and 2 bulls born in respective years were represented on top 100 by old single-trait models. Re-ranking of the daughters or sires by multiple-trait models suggest that this new multiple trait approach should be used for dairy cattle genetic evaluation and seed-stock selection in the future to increase the accuracy of multiple trait selection. Breeding values for these traits should also be calculated by new method for international genetic evaluation.

• Current Research on Agriculture and Life Sciences
• /
• v.6
• /
• pp.87-91
• /
• 1988

We studied the effects of the seed root weight and the local varieties on the yield and the quality of Cnidium officinale Makino root. The fresh and dried root weight per plant was found to be 92.7 g and 18.5 g in the large seed root(20-25 g), while 94.5 g and 17.0 g in the small seed root(15-20 g), respectively. The fresh and dried roots were produced 906.8kg/10a and 190.2kg/10a in the large seed root, but 721.2kg/10a and 165.2kg/10a in the small seed root, respectively. The root weight per plant, root yield per 10a and diethyl ether extract contents in root of Ul-Reung cultivar were higher than those of the other varieties. The root weight per plant and root yield per 10a were positively correlated with the contents of diethyl ether extracts in the large seed root, and with the ash contents of root in the small seed root. It is recommended for the high quality root production of cnidium officinale Makino to select and cultivate the large seed root(20-25 g) of Ul-Reung cultivar.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.17-28
• /
• 2018

In this study, catalytic activation using sulfuric acid lignin (SAL), the condensed solid by-product from saccharification process, with potassium hydroxide at $750^{\circ}C$ for 1 h in order to investigate its potential to nanoporous carbon In this study, catalytic activation using sulfuric acid lignin (SAL), the condensed solid by-product from saccharification process, with potassium hydroxide at $750^{\circ}C$ for 1 h in order to investigate its potential to nanoporous carbon material. Comparison study was also conducted by production of activated carbon from coconut shell (CCNS), Pinus, and Avicel, and each activated carbon was characterized by chemical composition, Raman spectroscopy, SEM analysis, and BET analysis. The amount of solid residue after thermogravimetric analysis of biomass samples at the final temperature of $750^{\circ}C$ was SAL > CCNS > Pinus > Avicel, which was the same as the order of activated carbon yields after catalytic activation. Specifically, SAL-derived activated carbon showed the highest value of carbon content (91.0%) and $I_d/I_g$ peak ratio (4.2), indicating that amorphous large aromatic structure layer was formed with high carbon fixation. In addition, the largest changes was observed in SAL with the maximum BET specific surface area and pore volume of $2341m^2/g$ and $1.270cm^3/g$, respectively. Furthermore, the adsorption test for three kinds of organic pollutants (phenol, 2,4-Dichlorophenoxyacetic acid, and carbofuran) were conducted, and an excellent adsorption capacity more than 90 mg/g for all activated carbon was determined using 100 ppm of the standard solution. Therefore, SAL, a condensed structure, can be used not only as a nanoporous carbon material with high specific surface area but also as a biosorbent applied to a carbon filter for remediation of organic pollutants in future.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.48-59
• /
• 2018

This study was conducted to suggest the effective management and recycling processes of coffee waste, which can be easily obtained from coffee shops and coffee-related products industries. Prior to the fabrication of pellets, the potential of coffee waste as a raw material of pellet was investigated through the examination of its chemical compositions and fuel characteristics. Major gradient included in coffee waste was holocellulose, followed by fat/oil and protein. Coffee waste contained a small quantity of ash (0.7%), such as calcium, sodium, potassium and magnesium. Interestingly, coffee waste was easily dried probably due to its porous structure. Pellets fabricated with coffee waste and larch sawdust showed good fuel characteristics, such as moisture content, ash content, density and durability. The pellets exceed greatly the minimum requirements of $1^{st}$-grade wood pellet standard designated by National Institute of Forest Science (NIFOS). Particularly, the high calorific value of coffee waste showed the potential as a raw material of pellet. However, owing to high nitrogen and sulfur contents, coffee waste is like to be used as a raw material of wood pellet for combined heat and power plants equipped with a reduction system of $NO_x$ and $SO_x$ gases. On the other hand, 91 wt% larch sawdust and 9 wt% coffee waste are required to fabricate the $1^{st}$-grade wood pellets designated by NIFOS. Pellets fabricated with the conditions are estimated to have nitrogen content of 0.298% and sulfur content of 0.03%. Lastly, if amounts of coffee waste and sawdust in the production of wood pellets are adequately adjusted according to its purchasing price, the manufacturing cost of pellet can effectively be reduced. In addition, it is expected tp prepare the effective recycling process of waste and to relieve the environmental burden with the reduction of waste from the commercialization of coffee waste/larch pellets.