• Journal of Biosystems Engineering
• /
• 제39권1호
• /
• pp.1-10
• /
• 2014

Purpose: This research was conducted to evaluate feasibility of a crank-type walking cultivators for weeding in furrowed upland. Methods: A walking cultivator developed by RDA was selected and evaluated with its working speed (S), cultivation depth (CD) and weeding performance (WP). The evaluation was performed in upland field on July and August, 2012. Also kinematic analysis of the machine was performed to draw out design improvements. Results: S in flat, uphill and downhill were about 0.11 m $s^{-1}$, 0.11 m $s^{-1}$, and 0.13 m $s^{-1}$ respectively. It was found that S had a low relevance with user conditions. The CD was 35 ~ 40 mm which was satisfied with the RDA guide for weeding machine. A wide variation was observed in values of WP depending on the growth stages of weeds and field conditions. The cultivator showed low performance in eliminating the well-grown weeds. Kinematic simulation revealed that high forward speed caused a high ratio of un-weeded area. Conclusions: The weeding performance of the cultivator was satisfactory for weeds in early growth stage but it showed difficulties in handling on up-slope and in entering up-land. Specifically, the weight of the cultivator was judged as overweight for female workers. The crank-hoe type cultivator was judged as unsuitable for small walking type machine due to weight of the four-bar linkage system. Kinematic analysis revealed that the ratio of crank speed to the ground speed must be 850 rpm s $m^{-1}$ (255 rpm based on 0.3 m $s^{-1}$) or greater to avoid uncultivated area. Selection of forward speed is a decisive factor in designing the weeding cultivator.

• 농업과학연구
• /
• 제48권4호
• /
• pp.1027-1037
• /
• 2021

This study aims to evaluate the performance of an electric multi-purpose cultivator through a simulation analysis. The simulation model was developed using commercial software, Simulation X, by applying the specifications of certain parts, such as an electric motor, a battery, and so on. The input parameter of the simulation was the engine load data according to the rotary tillage level using a conventional multi-purpose cultivator. The data were collected by configuring a load measurement system, and the load cycle was developed by repeating the data collection process under the most severe conditions. The average output engine torque values of conventional multi-purpose cultivator were 10.7, 13.0, 9.4, and 11.2 Nm in the D1P1, D1P2, D2P1, and D2P2 conditions, respectively. As a result of the simulation, the maximum values of the motor torque, rotational speed, and power of the electric multi-purpose cultivator were 16.8 Nm, 2,033.3 rpm, and 3.3 kW, respectively, and the motor was driven in sections within 70, 68, and 45% of the maximum output range. The rate of decrease of the battery state of charge (SOC) level per minute was approximately 0.6%, and it was possible to supply electric power to the motor for 9,550 sec. In the future study, research to verify and improve simulation models of electric multi-purpose cultivators should be conducted.

• Journal of Biosystems Engineering
• /
• 제39권4호
• /
• pp.274-282
• /
• 2014

Purpose: In this study, a hybrid power system was developed for agricultural machines with a 20-KW output capacity, and it was attached to a multi-purpose cultivator to improve the performance of the cultivator, which was evaluated using output tests. Methods: The hybrid system combined heterogeneous sources: an internal-combustion engine and an electric power motor. In addition, a power splitter was developed to simplify the power transmission structure. The cultivator using the hybrid system was designed to have increased fuel efficiency and output power and reduced exhaust gas emissions, while maintaining the functions of existing cultivators. Results: The fuel consumption for driving the cultivator in the hybrid engine vehicle (HEV) mode was 341 g/KWh, which was 36% less than the consumption in the engine (ENG) mode for the same load. The maximum power take off output of the hybrid power system was 12.7 KW, which was 38% more than the output of the internal-combustion engine. In the HEV mode, harmful exhaust gas emissions were reduced; i.e., CO emissions were reduced by 36~41% and NOx emissions were reduced by 27~51% compared to the corresponding emissions in the ENG mode. Conclusions: The hybrid power system improved the fuel efficiency and reduced exhaust gas emissions in agricultural machinery. Lower exhaust gas emissions of the hybrid system have considerable advantages in closed work environments such as crop production facilities; therefore, agricultural machinery with less exhaust gas emissions should be commercialized. However, the high manufacturing cost and complexity of the proposed system are challenges which need to be solved in the future.

• 제어로봇시스템학회논문지
• /
• 제21권5호
• /
• pp.447-452
• /
• 2015

A hybrid power system was developed for agricultural machines with a 20kW output capacity, and it was attached to a multi-purpose cultivator to improve the performance of the cultivator. The hybrid system combined heterogeneous sources: an internal-combustion engine and an electric power motor. In addition, a power splitter was developed to simplify the power transmission structure. The cultivator using a hybrid system was designed to have increased fuel efficiency and output power and reduced exhaust gas emissions, while maintaining the functions of existing cultivators. The fuel consumption for driving the cultivator in the hybrid engine vehicle (HEV) mode was 341g/kWh, which was 36% less than the consumption in the engine (ENG) mode for the same load. The maximum power take off output of the hybrid power system was 12.7kW, which was 38% more than the output of the internal-combustion engine. In the HEV mode, harmful exhaust gas emissions were reduced; i.e., CO emissions were reduced by 36~41% and NOx emissions were reduced by 27~51% compared to the corresponding emissions in the ENG mode. The hybrid power system improved the fuel efficiency and reduced exhaust gas emissions in agricultural machinery. The hybrid system's lower exhaust gas emissions have considerable advantages in closed work environments such as crop production facilities. Therefore, agricultural machinery with less exhaust gas emissions should be commercialized.

• Journal of Biosystems Engineering
• /
• 제38권4호
• /
• pp.270-278
• /
• 2013

Purpose: Using agricultural machinery was not easy in the conventional shading structure, specified as a standard facility by standard cultivation methods for ginseng. Thus, this study designed the new types of facility allowing machine access by modifying the conventional type. Methods: Two types of facility (i.e. wide roof type and long & short roof type) were designed and installed in an experimental site to evaluate its growing environments and applicability of riding-type cultivator. Results: From the results of incoming light measurement, all three types (i.e. two new types and a conventional type) of shading structures blocked the incoming light after 9:00 am. The temperature distribution inside the new types was similar with the one in the conventional type, so the growth of ginseng was in good condition in all three types of facility. The riding-type cultivator was operated well with the low speed first gear of 0.13 m/s in the new types. However, a long & short typed roof needs to be raised 18 cm height in order to use the cultivator. Conclusions: With the results of this study, the new types of roof can be used in the ginseng farm in that they satisfied the growing environments for ginseng and the needs for agricultural mechanization.

• Journal of Biosystems Engineering
• /
• 제21권1호
• /
• pp.3-9
• /
• 1996

Sowing with an automatic seed metering device is increasing in popularity. Since 100% planting is not likely, a major problem is to find any place which contains no seeds between row spacings in the agricultural field. Automatic sowing technology, including the implementation of a microcomputer, appears to be an attractive alternative to the use of manual labor for accomplishing this task. Thus, the multi-purpose seeder attached to a cultivator was designed and constructed with an automatic seed metering device. This seeder proved to be a reliable system for sowing seeds in the agricultural field. Multi-purpose seeder for cultivator consists of an automatic seed metering device, a trench device, a covering device, and a press wheel

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 학술발표대회 논문집
• /
• pp.187-191
• /
• 1996

• Journal of Biosystems Engineering
• /
• 제39권1호
• /
• pp.11-20
• /
• 2014

Purpose: Walking type cultivator used for weeding generated excessive handle vibration as well as bouncing motion depending on the weeding speed. This research was conducted to define a design factor of the rotary weeding blades for reducing soil reaction forces as well as hand vibration. Methods: The motion and forces acting on the rotary blades were reviewed to find out the most influencing parameter on hand vibration. The installation angle (IA) of the blade was selected and analyzed to determine the condition of no reaction force less. For removing the unnecessary upward soil reaction, the design factor theory of weeding blade was suggested based on geometrics and dynamics. For evaluation of design factor theory, the experiment in situ was performed base on ISO 5349:1. The vibration $a_{hv}$ and theoretical value $X_{MF}$ were compared with two groups that one was positive group ($X_{MF}$ > 0) and the other was negative group ($X_{MF}$ < 0). Results: $X_{MF}$ was derived from rotational velocity, forward velocity, disk diameter, weeding depth, blade's width and IA of blade. Two groups had significant difference (p < 0.05). In aspect of the group mean total exposure duration, positive group was 17.53% bigger than negative group. When disk radius 100, 150 and 200 mm, minimum IAs were $4{\sim}27^{\circ}$, $3{\sim}15^{\circ}$ and $2{\sim}10^{\circ}$, respectively. A spread sheet program which calculated XMF was developed by Excel 2013. Conclusions: According to this result, minimum IA of weeding blade for soil reaction reduction could be obtained. For reduction hand-arm vibration and power consumption, minimum IA is needed.

• 드라이브 ㆍ 컨트롤
• /
• 제20권2호
• /
• pp.31-39
• /
• 2023

The aim of this study was to measure and analyze engine load factor (LF) according to working conditions (operation type and gear stage) of small agricultural multi-purpose cultivator to estimate the emission of air pollutants. To calculate LF, a torque sensor capable of collecting torque and rotational speed was installed on the engine output shaft and DAQ was used to collect data. A field test was conducted with major operation of a cultivator and tillage operations (plow tillage and rotary tillage). Engine power was calculated using engine torque and rotational speed and LF was calculated using real-time power and rated power. In addition, unified LF was calculated using the weight for each operation and the average LF for each operation. As a result, average LF values at 1.87 and 3.10 km/h by plow tillage were 0.50 and 0.69, respectively. Average LF values at 1.87 and 3.10 km/h by rotary tillage were 0.70 and 0.78, respectively. Furthermore, unified LF calculated in consideration of the weight factor showed a value of 0.65, which was 135% higher than the conventional LF (0.48). Results of this study could be used as basic information for realizing LF values in the field of agricultural machinery.

• 한국토양비료학회지
• /
• 제17권2호
• /
• pp.155-160
• /
• 1984

토양(土壤) 물리성(物理性)이 농기계(農機械) 작업능률(作業能率)에 미치는 영향(影響)을 구명(究明)하기 위하여 토성(土性)과 수분조건(水分條件)이 각각 상이(相異)한 논토양(土壤)에서 제반(諸般) 토양물리성(土壤物理性)을 조사(調査)하고 경운기(耕耘機)와 트랙타를 이용(利用)한 작업능률(作業能率)을 조사(調査)한 결과(結果)는 다음과 같다. 1. 토양(土壤)의 경도(硬度), 전단저항(剪斷抵抗), 마찰저항(摩擦低沆), 판(板) 및 차륜침하량(車輪沈下量), 진행저하율(進行低下率) 및 족적심등(足蹟深等)은 토성(土性)과 수분함량(水分含量)에 따라 변화(變化)되었으며 이에 따라 작업능률(作業能率)도 큰 차이(差異)가 있었다. 2. 동력경운기(動力耕耘機)의 작업능률(作業能率)은 전단저항(剪斷抵抗)이 $200{\sim}450g/cm^2$ 범위(範圍)에서 가장 양호(良好)하며 $200g/cm^2$ 이하(以下)에서는 경운기(耕耘機)와 트랙타 작업(作業)이 불량(不良)하였다. 3. 작업능률(作業能率)이 높은 경도범위(硬度範圍)는 트랙타가 $8{\sim}12kg/cm^2$ 이었고 경운기(耕耘機)는 $6{\sim}10kg/cm^2$이었다. 4. 족적심(足跡深)은 기존(旣存) 기기(器機)의 측정치(測定値)와 상관(相關)이 높았고 적정(適正) 족적심(足跡深)은 1~2cm, 작업(作業) 불가능(不可能) 범위(範圍)는 경운기(耕耘機) 2cm이상(以上), 트랙타 5cm이상(以上)이었다.