• Korean Journal of Materials Research
• /
• v.17 no.4
• /
• pp.215-221
• /
• 2007

The effect of $CF_4$ plasma treatment condition on the interfacial adhesion energy of inkjet printed Ag/polyimide system is evaluated from $180^{\circ}$ peel test by calculating the plastic deformation energy of peeled metal films. Interfacial fracture energy between Ag and as-received polyimide was 5.5 g/mm. $CF_4$ plasma treatment on the polyimide surface enhanced the interfacial fracture energy up to 17.6 g/mm. This is caused by the increase in the surface roughness as well as the change in functional group of the polyimide film due to $CF_4$ plasma treatment on the polyimide surface. Therefore, both the mechanical interlocking effect and the chemical bonding effect are responsible for interfacial adhesion improvement in ink jet printed Ag/polyimide systems.

• Journal of Surface Science and Engineering
• /
• v.48 no.4
• /
• pp.158-162
• /
• 2015

To substitute indium tin oxide (ITO), many substituents have been studied such as metal nanowires, carbon based materials, 2D materials, and conducting polymers. These materials are not good enough to apply to an electrode because theses exhibit relatively high resistance. So metal grids are required as an additionalelectrode to improve the conductivities of substituents. The metal grids were printed by electrohydrodynamic printing system using Ag nanoparticle based ink. The Ag grids showed high uniformity and the line width was about $10{\mu}m$. The Ag nanoparticles are surrounded by dispersants such as unimolecular and polymer to prevent aggregation between Ag nanoparticles. The dispersants lead to low conductivity of Ag grids. Thus, the sintering process of Ag nanoparticles is strongly recommended to remove dispersants and connect each nanoparticles. For sintering process, the interface and microstructure of the Ag grid were controlled in 1.0 torr Ar atmosphere at aound $400^{\circ}C$ of temperature. From the sintering process, the uniformity of the Ag grid was improved and the defects on the Ag grids were reduced. As a result, the resistivity of Ag grid was greatly reduced up to $5.03({\pm}0.10){\times}10^{-6}{\Omega}{\cdot}cm$. The metal grids embedded substrates containing low pressure Ar sintered Ag grids showed 90.4% of transmittance in visible range with $0.43{\Omega}/{\square}$ of sheet resistance.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.18.2-18.2
• /
• 2010

For the past a few years, we have intensively researched the printable inorganic conductors and ZnO-based amorphous oxide semiconductors (AOSs) for thin-film transistors. For printable conductor materials, we have focused on the aqueous Ag and Cu ink which possess a variety of advantages, comparing with the conventional metal inks based on organic solvent system. The aqueous Ag ink was designed to achieve the long-term dispersion stability using a specific polymer which can act as a dispersant and capping agent, and the aqueous Cu ink was carefully formulated to endow the oxidation stability in air and even aqueous solvent system. The both inks were successfully printed onto either polymer or glass substrate, exhibiting the superior conductivity comparable to that of bulk one. For printable ZnO-based AOSs, we have researched the noble way to resolve the critical problem, a high processing-temperature above $400^{\circ}C$, and recently discovered that Ga doping in ZnO-based AOSs promotes the formation of oxide lattice structures with oxygen vacancies at low annealing-temperatures, which is essential for acceptable thin-film transistor performance. The mobility dependence on annealing temperature and AOS composition was analyzed, and the chemical role of Ga are clarified, as are requirements for solution-processed, low-temperature annealed AOSs.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.11-15
• /
• 2010

In this study, to fabricate a low-resistance and high optical transparency electrode film, the following steps were performed: the design and manufacture of electroforming stamp, the fabrication of a thermal roll-imprinted polycarbonate (PC) patterned films, the filled low-resistance Ag paste using doctor blade process on patterned PC films and spin coating by conductive polymers. As a result of PC films imprinted line width of $26.69{\pm}2\;{\mu}m$, channel length of $247.57{\pm}2\;{\mu}m$, and pattern depth of $7.54{\pm}0.2\;{\mu}m$. Ag paste to fill part of the patterned film with conductive polymer coating and then the following parameters were obtained: a sheet resistance of $11.1\;{\Omega}/sq$ optical transparency values at a wavelength of 550 nm was 80.31 %.

• Journal of Aerospace System Engineering
• /
• v.13 no.4
• /
• pp.37-42
• /
• 2019

The objective of this study was to study the bending characteristics of Ag nano ink using EHD (Electrohydrodynamics) inkjet printing technology for flexibility and miniaturization of devices. The optimal conditions for the technology were derived, and bending characteristics of the Ag nano circuit obtained. For the EHD printing, it is essential to find the optimal point for each parameter such as material characteristics, density, flow rate, voltage, discharge height etc. Therefore, it was derived as the point from the working height and the applied voltage. Also, bending characteristics are confirmed by measuring resistance with each radius of curvature using a fabricated bending module. It was confirmed that rate of resistance change increases rapidly as the radius of curvature increases.

• Journal of the Korean Vacuum Society
• /
• v.22 no.3
• /
• pp.156-161
• /
• 2013

We fabricated transparent conductive electrodes with silver (Ag) nanofibers by electrospinning process. Ag nanofibers have high aspect ratio and fused junctions which result in low sheet resistance. Electrospinning is a fast and efficient process to fabricate continuous one-dimensional (1D) nanofibers. Ag/polymer ink were prepared in polymer matrix solution by a sol-gel method. Then, Ag/polymer nanofibers precursors are heated at $200{\sim}500^{\circ}C$ in air for 2 h to eliminate partially the polymers. The topographical features of the Ag nanofibers were characterized by FE-SEM, and the electrical property was analyzed through I-V measurement system. Finally, optical property was measured using UV/VIS spectroscopy. The transparent conductive electrodes with Ag nanofibers exhibited a sheet resistance (Rs) of $250{\Omega}/sq$ at a transparency (T) of 83%. Transparent conductive films, contain the Ag nanofibers as conductive materials, have good electrical, optical, and mechanical properties. Therefore, it is expected to be useful for the application of flexible display in the future.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.955-956
• /
• 2008

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.743-744
• /
• 2011

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1340_1341
• /
• 2009

In this report, high-resolution metal electrode patterning is demonstrated by using selective surface treatment and dip casting for low-cost printed electronic applications. On hydrophobic octadecyltrichlorosilane treated $SiO_2$ surface, deep UV irradiation was performed through a patterned quartz photomask to selectively control the surface energy of the $SiO_2$ layer. The deep UV irradiated region becomes hydrophilic and by dipping into Ag nano-ink, Ag patterns were formed on the surface. Using this patterning technique, line patterns and dot arrays having less than $10{\mu}m$ pitch were fabricated.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.2.3-2.3
• /
• 2011

With increased interest in printed devices, various metal nano inks have been investigated as candidates materials for printed electrodes and wiring as well as conductive film substituting photo-lithography process. Recent advances in organic conductive polymer allow us to fabricate high performance printed device. Meanwhile, there was several attempts to fabricate conductive films by mixing conductive polymer with metal nano-particle or nano-wires. The presence of Ag nanowires in conductive polymer mixture have shown good potential in organic photovoltaic devices.