• 한국추진공학회지
• /
• 제24권5호
• /
• pp.56-64
• /
• 2020

29.7% 축소 NASA 표준 연구 모형에 대하여 소형 저속 풍동에서 시험을 수행하였다. 풍동시험 모형은 NASA Langley 연구소와 AIAA 항력추정 워크숍 위원회의 지침에 따라 알루미늄으로 제작하였다. 풍동의 능력 한계 등으로 상대적으로 낮은 레이놀즈수인 0.3 × 10⁶ 에서 정적 힘과 모멘트를 측정하였다. 세 가지 타입(핀 스팅, 블레이드 스팅, 벨리 스팅) 모형지지부에 대하여 피칭모멘트를 비교하였다. 보정된 벨리 스팅과 핀 스팅에 의한 피칭모멘트 보정량은 비슷하였으며 블레이드 스팅에 의한 피칭모멘트 값이 가장 적었다.

• Advances in aircraft and spacecraft science
• /
• 제9권3호
• /
• pp.263-278
• /
• 2022

The time-varying structural reliability of an aeroelastic launch vehicle subjected to stochastic parameters is investigated. The launch vehicle structure is under the combined action of several stochastic loads that include aerodynamics, thrust as well as internal combustion pressure. The launch vehicle's main body structural flexibility is modeled via the normal mode shapes of a free-free Euler beam, where the aerodynamic loadings on the vehicle are due to force on each incremental section of the vehicle. The rigid and elastic coupled nonlinear equations of motion are derived following the Lagrangian approach that results in a complete aeroelastic simulation for the prediction of the instantaneous launch vehicle rigid-body motion as well as the body elastic deformations. Reliability analysis has been performed based on two distinct limit state functions, defined as the maximum launch vehicle tip elastic deformation and also the maximum allowable stress occurring along the launch vehicle total length. In this fashion, the time-dependent reliability problem can be converted into an equivalent time-invariant reliability problem. Subsequently, the first-order reliability method, as well as the Monte Carlo simulation schemes, are employed to determine and verify the aeroelastic launch vehicle dynamic failure probability for a given flight time.

• 한국항공우주학회지
• /
• 제50권11호
• /
• pp.755-762
• /
• 2022

유도무기 형상에 대한 풍동시험 데이터를 다양한 반경험식 기반 코드 및 CFD해석 코드를 이용한 공력 해석 결과와 비교하였다. 주날개 형상 2종과 주날개와 꼬리날개가 일렬로 늘어선 inline 형상 및 서로 교차되는 interdigitate 형상 등 총 3가지 형상에 대해 시험결과와 비교하였으며, 형상의 특징에 따라 코드별로 차이가 있는 것을 확인하였다. 추가적으로 CFD해석결과를 유동가시화 시험결과와 비교함으로써 CFD 해석 코드가 와류의 흐름을 정확하게 예측하는 것을 확인하였다.

• 한국전자파학회논문지
• /
• 제29권3호
• /
• pp.233-240
• /
• 2018

레이다를 사용한 미사일 표적의 정확한 탐지 및 추적을 위해서는 채프 구름의 레이다 반사 단면적(Radar Cross Section: RCS)에 대한 분석이 반드시 필요하다. 따라서 본 논문에서는 다양한 환경에서 보다 효과적인 채프 구름의 RCS 분석을 위해 채프 구름 내 채프들을 개별적으로 계산하여 합하는 RCS 예측 방법과 공기역학 모델 기반의 확률밀도분포 모델을 사용한 RCS 예측 방법을 비교 및 분석하였다. 여기서, 상기 두 기법을 보다 더 정밀하게 비교 및 분석하기 위해 본 논문에서는 상용 전자기 수치해석 소프트웨어인 FEKO 7.0을 활용하여 반 파장 다이폴 형태의 단일 채프 CAD 모델의 RCS 값을 획득하여 채프 구름의 RCS를 모사하였다. 분석 결과, 확률 밀도 분포 모델을 사용한 경우 보다 효율적으로 체프 구름의 RCS 값을 예측할 수 있음을 확인하였다.

• Journal of Mechanical Science and Technology
• /
• 제20권12호
• /
• pp.2292-2314
• /
• 2006

Efficient numerical method is developed for the prediction of aerodynamic noise generation and propagation in low Mach number flows such as aeolian tone noise. The proposed numerical method is based on acoustic/viscous splitting techniques of which acoustic solvers use simplified linearised Euler equations, full linearised Euler equations and nonlinear perturbation equations as acoustic governing equations. All of acoustic equations are forced with immersed surface dipole model which is developed for the efficient computation of aerodynamic noise generation and propagation in low Mach number flows in which dipole source, originating from unsteady pressure fluctuation on a solid surface, is known to be more efficient than quadrupole sources. Multi-scale overset grid technique is also utilized to resolve the complex geometries. Initially, aeolian tone from single cylinder is considered to examine the effects that the immersed surface dipole models combined with the different acoustic governing equations have on the overall accuracy of the method. Then, the current numerical method is applied to the simulation of the aeolian tones from twin cylinders aligned perpendicularly to the mean flow and separated 3 diameters between their centers. In this configuration, symmetric vortices are shed from twin cylinders, which leads to the anti-phase of the lift dipoles and the in-phase of the drag dipoles. Due to these phase differences, the directivity of the fluctuating pressure from the lift dipoles shows the comparable magnitude with that from the drag dipoles at 10 diameters apart from the origin. However, the directivity at 100 diameters shows that the lift-dipole originated noise has larger magnitude than, but still comparable to, that of the drag-dipole one. Comparison of the numerical results with and without mean flow effects on the acoustic wave emphasizes the effects of the sheared background flows around the cylinders on the propagating acoustic waves, which is not generally considered by the classic acoustic analogy methods. Through the comparison of the results using the immersed surface dipole models with those using point sources, it is demonstrated that the current methods can allow for the complex interactions between the acoustic wave and the solid wall and the effects of the mean flow on the acoustic waves.

• Wind and Structures
• /
• 제36권4호
• /
• pp.237-247
• /
• 2023

The emergence of high-rise buildings has necessitated frequent structural health monitoring and maintenance for safety reasons. Wind causes damage and structural changes on tall structures; thus, safe structures should be designed. The pressure developed on tall buildings has been utilized in previous research studies to assess the impacts of wind on structures. The wind tunnel test is a primary research method commonly used to quantify the aerodynamic characteristics of high-rise buildings. Wind pressure is measured by placing pressure sensor taps at different locations on tall buildings, and the collected data are used for analysis. However, sensors may malfunction and produce erroneous data; these data losses make it difficult to analyze aerodynamic properties. Therefore, it is essential to generate missing data relative to the original data obtained from neighboring pressure sensor taps at various intervals. This study proposes a deep learning-based, deep convolutional generative adversarial network (DCGAN) to restore missing data associated with faulty pressure sensors installed on high-rise buildings. The performance of the proposed DCGAN is validated by using a standard imputation model known as the generative adversarial imputation network (GAIN). The average mean-square error (AMSE) and average R-squared (ARSE) are used as performance metrics. The calculated ARSE values by DCGAN on the building model's front, backside, left, and right sides are 0.970, 0.972, 0.984 and 0.978, respectively. The AMSE produced by DCGAN on four sides of the building model is 0.008, 0.010, 0.015 and 0.014. The average standard deviation of the actual measures of the pressure sensors on four sides of the model were 0.1738, 0.1758, 0.2234 and 0.2278. The average standard deviation of the pressure values generated by the proposed DCGAN imputation model was closer to that of the measured actual with values of 0.1736,0.1746,0.2191, and 0.2239 on four sides, respectively. In comparison, the standard deviation of the values predicted by GAIN are 0.1726,0.1735,0.2161, and 0.2209, which is far from actual values. The results demonstrate that DCGAN model fits better for data imputation than the GAIN model with improved accuracy and fewer error rates. Additionally, the DCGAN is utilized to estimate the wind pressure in regions of buildings where no pressure sensor taps are available; the model yielded greater prediction accuracy than GAIN.

• 한국항공우주학회지
• /
• 제38권5호
• /
• pp.414-420
• /
• 2010

본 연구에서는 천음속 날개/동체 모텔에 대한 축소모델 (Reduced Order Model; ROM)의 정확성을 검증하고, Proper Orthogonal Decomposition(POD)을 이용한 최적설계를 통해 그 효율성을 검토하였다. full order 공력해석을 통한 Snapshot을 추출하기 위해 삼차원 오일러 방정식을 이용하였으며, 이들 Snapshot들을 통해 날개/동체 모델 주위 유동장의 거동을 모사하는 POD의 기저벡터를 계산 하였다. 이러한 과정을 거쳐 구축된 축소모텔은 6개의 Case들로 검증하였으며, 그 결과 ROM을 이용해 관심영역에 대한 유동장의 예측을 할 수 있다는 것을 확인하였다. 그리고 ROM을 통한 날개/동체 모델의 최적설계를 수행 하였으며, 그 결과는 반응면모델 (Response Surface Model; RSM)을 이용한 최적설계 결과와 비교 하였다. 이를 통해 ROM을 바탕으로한 최적설계가 RSM을 이용한 것보다 효율적임을 확인하였다.

• 한국유체기계학회 논문집
• /
• 제12권3호
• /
• pp.44-52
• /
• 2009

Small scale steam turbines are used as mechanical drivers in chemical process plant or power generators. In this study, a design technology was developed for a 100kW class steam turbine which will be used for removing $CO_2$ from the emission gas on a reheated cycle system. This turbine is operated at a low inlet total pressure of $5\;kgf/cm^2$. It consists of two stages and operates at the partial admission. For the meanline analysis, a performance prediction method was developed and it was validated through the performances on the operating small steam turbines which are using at plants. Their results showed that the output power was predicted within 10% deviation although the steam turbines adopted in this analysis were operated at different flow conditions and rotor size. The turbine blades was initially designed based on the computed results obtained from the meanline analysis. A supersonic nozzle was designed on the basis of the operating conditions of the turbine, and the first stage rotor was designed using a supersonic blade design method. The stator and second stage rotor was designed using design parameters for the blade profile. Finally, Those blades were iteratively modified from the flow structures obtained from the three-dimensional flow analysis to increase the turbine performance. The turbine rotor system was designed so that it could stably operate by 76% separation margin with tilting pad bearings.

• 한국항공우주학회지
• /
• 제41권4호
• /
• pp.261-267
• /
• 2013

본 논문에서는 헬리콥터 전진비행 조건에서 플래핑모션에 대하여 축소 로터 실험을 통하여 실험결과와 이론적인 예측결과를 비교하였다. 축소로터 성능 실험은 충남대학교 아음속 풍동에서 수행하였으며 1.8 x 1.8m의 개방형 시험부를 사용하였다. 전진비행조건에서의 실험 결과에 의하면 축소로터의 전진비행조건에서의 추력 결과를 고정한 조건에서 동력계수는 차이가 있는 것을 확인 할 수 있었다. 또한, 공력 성능 측정 결과와 이론적인 예측결과의 비교를 통하여 헬리콥터의 플랩핑 각도의 범위에 대하여 비교하여 보았다. Coning 각도, 횡방향과 종방향에 대한 플래핑 각도에 대해서는 실험결과와 예측결과의 유사함을 확인하였다.

• Smart Structures and Systems
• /
• 제15권6호
• /
• pp.1393-1410
• /
• 2015

An original sensor system based on Fiber Bragg Gratings (FBG) for the strain monitoring of an adaptive wing element is presented in this paper. One of the main aims of the SARISTU project is in fact to measure the shape of a deformable wing for performance optimization. In detail, an Adaptive Trailing Edge (ATE) is monitored chord- and span-wise in order to estimate the deviation between the actual and the desired shape and, then, to allow attaining a prediction of the real aerodynamic behavior with respect to the expected one. The integration of a sensor system is not trivial: it has to fit inside the available room and to comply with the primary issue of the FBG protection. Moreover, dealing with morphing structures, large deformations are expected and a certain modulation is necessary to keep the measured strain inside the permissible measure range. In what follows, the mathematical model of an original FBG-based structural sensor system is presented, designed to evaluate the chord-wise strain of an Adaptive Trailing Edge device. Numerical and experimental results are compared, using a proof-of-concept setup. Further investigations aimed at improving the sensor capabilities, were finally addressed. The elasticity of the sensor structure was exploited to enlarge both the measurement and the linearity range. An optimisation process was then implemented to find out an optimal thickness distribution of the sensor system in order to alleviate the strain level within the referred component.