• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.456-459
• /
• 2010

Icing is one of the most serious hazards for aircraft. The amount and rate of icing depend on a number of meteorogical and aerodynamic factors. Of primary importance are amount of liquid water content of droplets, their size, the temperature of aircraft surfaces, the collection efficiency, and the extent of supercooled droplets. In this study, in-flight icing analysis of low reynolds number high aspect ratio wing is carried out by using FENSAP-ICE. Each liquid water contents with altitude is obtained from FAR 25 Appendix-C. And the collectoin efficiency is calculated to check out the ice accretion position of wing with two angles of attack. The degradation of aerodynamic characteristics of aircraft are figured out by investigating the accretion of rime and glaze ice.

• Wind and Structures
• /
• 제10권5호
• /
• pp.421-435
• /
• 2007

A two-dimensional flutter analysis method (2d-3DOF method) was developed to simultaneously investigate the relationship between oscillation parameters and aerodynamic derivatives of three degrees of freedom, and to clarify the coupling effects of different degrees of freedom in flutter instability. With this method, the flutter mechanism of two typical bridge deck sections, box girder section and two-isolated-girder section, were numerically investigated, and both differences and common ground in these two typical flutter phenomena are summarized. Then the flutter stabilization effect and its mechanism for long-span bridges with box girders by using central-slotting were studied by experimental investigation of aerodynamic stability and theoretical analysis of stabilizing mechanism. Possible explanation of new findings in the evaluation trend of critical wind speed through central vent width is finally presented.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.262-267
• /
• 2016

In this paper, to design Human Powered Aircraft(HPAC) with high aspect ratio wing which behave with large displacement under lift distribution causing a failure itself, then steel wire has been designed to prevent its failure. unit load method is used to calculate reaction force on wire and Optimal Triangle(OPT) membrane is employed to analyze its main wing spar with large displacement. EDISON CSD solver, linear static analysis and co-rotational nonlinear static anaysis both using OPT membrane produce behaviors of beam for each case of wire location about main wing spar, and aerodynamic coefficient also, by using aerodynamic analysis tool.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.638-642
• /
• 2008

Computational methods based on the solution of the flow model are widely used for the analysis of lowspeed, inviscid, attached-flow problems. Most of such methods are based on the implementation of the internal Dirichlet boundary condition. In this paper, the time-domain panel method uses the piecewise constant source and doublet singularities. The present method utilizes the time-stepping loop to simulate the unsteady motion of the rotary wing blade. The wake geometry is calculated as part of the solution with no special treatment. To validate the results of aerodynamic characteristics, the typical blade was chosen such as, Caradonna-Tung blade and present results were compared with the experimental data and the other numerical results in the single blade condition and two blade condition. This isolated rotor blade model consisted of a two bladed rotor with untwisted, rectangular planform blade. Computed flow-field solutions were presented for various section of the blade in the hovering mode.

• 한국항공우주학회지
• /
• 제40권11호
• /
• pp.957-962
• /
• 2012

비행체 구조는 공기력에 의해 변형이 발생하고 이 구조의 변형은 다시 공기력의 변화를 유발하므로 비행체 구조 시스템의 고정밀 설계를 위해서는 공력/구조 연계 해석이 필요하다. 그러나 발생하는 변형이 비선형 구조 해석을 요구할 정도로 큰 경우, 선형 시스템에서와 같이 공력 해석과 구조 해석을 순차적으로 반복하는 연계 해석 기법은 바람직하지 않다. 구조적 변형에 따라 변하는 공기력을 충분히 고려하지 못하며, 소요 시간 또한 크기 때문이다. 본 연구는 공력장 내부의 비선형 구조의 거동을 보다 효율적으로 예측할 수 있는 공력/구조 연계 해석 기법을 다룬다. 즉, 비선형 구조 해석 단계 도중에 주기적으로 공력 해석을 통한 외력 업데이트를 수행하는 알고리즘을 제안한다. 또한 고세장비의 유연날개를 가지는 글로벌 호크 모델을 사용하여 여러 가지 기법의 비선형 공력/구조 연계 해석의 결과를 비교하였다.

• 한국전산유체공학회지
• /
• 제16권1호
• /
• pp.48-52
• /
• 2011

Aerodynamic analysis was done for a fuselage and wing configuration of a mid-sized aircraft using unsteady 3-dimensional Navier-Stokes solver. Various turbulent models including a transitional SST were used to observe a dynamic stall as well as cruise characteristics. Also, different mesh moving methods were evaluated. Flow hysteresis which causes dynamic stall was investigated through flow field investigations.

• Wind and Structures
• /
• 제18권2호
• /
• pp.155-180
• /
• 2014

The safety of road vehicles on the ground in crosswind has been investigated for many years. One of the most important fundamentals in the safety analysis is aerodynamic characteristics of a vehicle in crosswind. The most common way to study the aerodynamic characteristics of a vehicle in crosswind is wind tunnel tests to measure the aerodynamic coefficients and/or pressure coefficients of the vehicle. Due to the complexity of wind tunnel test equipment and procedure, the features of flow field around the vehicle are seldom explored in a wind tunnel, particularly for the vehicle moving on the ground. As a complementary to wind tunnel tests, the numerical method using computational fluid dynamics (CFD) can be employed as an effective tool to explore the aerodynamic characteristics of as well as flow features around the vehicle. This study explores crosswind effects on a high-sided lorry on the ground with and without movement through CFD simulations together with wind tunnel tests. Firstly, the aerodynamic forces on a stationary lorry model are measured in a wind tunnel, and the results are compared with the previous measurement results. The CFD with unsteady RANS method is then employed to simulate wind flow around and wind pressures on the stationary lorry. The numerical aerodynamic forces are compared with the wind tunnel test results. Furthermore, the same CFD method is extended to investigate the moving vehicle on the ground in crosswind. The results show that the CFD results match with wind tunnel test results and the current way using aerodynamic coefficients from a stationary vehicle in crosswind is acceptable. The CFD simulation can provide more insights on flow field and pressure distribution which are difficult to be obtained by wind tunnel tests.

• Wind and Structures
• /
• 제38권1호
• /
• pp.59-74
• /
• 2024

Large Eddy Simulation (LES) is used to explore the influence of vibration frequency and amplitude on the aerodynamic performance of a rectangular cylinder with an aspect ratio of B/D=5 (B: breadth; D: depth of cylinder) at a Reynolds number of 22,000 near resonance frequency. In smooth flow conditions, the research employs a sequence of three-dimensional simulations under forced vibration with diverse frequency ratios f_e / f_o = 0.8-1.2 (f_e : oscillation frequency; f_o : Strouhal frequency when the rectangular cylinder is stationary ) and oscillation amplitudes A_h/D = 0.05 - 0.3. The individual influences of f_e / f_o and A_h/D on the characteristics of integrated and distributed aerodynamic forces are the focal points of discussion. For the integrated aerodynamic force, particular emphasis is placed on the analysis of the dependence of velocity-proportional component C₁ and displacement-proportional component C₂ of unsteady aerodynamic force on amplitude and frequency ratio. Near the resonance frequency, the dependencies of C₁ and C₂ on amplitude are stronger than that of frequency ratio. For the distributed aerodynamic force, the increase in frequency and amplitude promotes the position of the main vortex core and reattachment to the leading edge in the streamwise direction. In the spanwise direction, vibration enhances the spanwise correlation of aerodynamic force to weaken the three-dimensional effect of the flow field, and a lower frequency ratio and larger amplitude amplify this effect.

• 한국입자에어로졸학회지
• /
• 제19권4호
• /
• pp.155-164
• /
• 2023

APS (Aerodynamic Particle Sizer) and OPC (Optical Particle Counter) have been widely used to real-time measurement of indoor and outdoor aerosols. The APS measures the size distribution based on an aerodynamic diameter, while the OPC uses optical diameter to measure the size distribution of aerosols. Since obtaining a size distribution based on aerodynamic diameter is important to understand aerosol characteristics, lots of researcher had been developed experimental equations which can convert optical diameter into aerodynamic diameter. However, previous studies have conducted repeated experiments on particles having a single diameter. In this study, an experimental method of converting optical diameter into aerodynamic diameter through a single experiment was presented. The collection efficiencies of an axial cyclone were measured using APS and OPC at the same time, and the correlation equation between aerodynamic diameter and optical diameter was driven through a theoretical model. Using the proposed method, the size distribution of NaCl particles measured by OPC showed a high correlation with the size distribution obtained by APS (0.93 of R-squared value). In the tests conducted on ISO A1, A2, and A4 test particles, the converted OPC size distribution tended to be similar to the APS size distribution, and for each of test particles (ISO A1, A2, and A4), the R-squared values for the APS particle size distribution were 0.75, 0.86, and 0.89, respectively.

• 한국터널지하공간학회 논문집
• /
• 제15권6호
• /
• pp.625-635
• /
• 2013

유럽 등 해외에서는 TBM 굴착방식을 이용한 터널이 다수 건설되고 있지만, 국내에서는 거의 적용되고 있지 않다. TBM 철도터널의 적용성을 높이기 위해서는 토목적 설계요소와 공기역학적 영향을 고려한 최적단면을 선정할 필요가 있다. 이러한 최적단면의 선정시에는 터널 연장, 열차 속도, 전차선 높이, 공동규 규격 등 토목적인 설계요소에 대한 고려와 함께 공기역학적 영향을 검토하여 적정 단면 계획의 수립이 필요하다. 공기역학적 검토시에는 최근 철도터널의 고속화를 고려하고 적절한 분석기준의 수립이 필요하지만 현재 국내에서는 관련기준이 없어 터널마다 상이한 공기압 분석기준이 적용되고 있는 실정이다. 따라서 본 연구에서는 국내외 이명감 및 미기압 분석기준에 대하여 검토하고, TBM 터널단면별 공기역학적 분석을 통해서 TBM 철도터널의 단면선정시 공기역학적 영향과의 상관관계에 대해 분석하였다.