• 대한소아치과학회지
• /
• 제26권3호
• /
• pp.479-485
• /
• 1999

복합레진을 이용한 수복은 재료의 낮은 강도와 중합수축으로 인한 변연 누출 그리고 상아질과의 결합력 등으로 인해 제한된 범위에서만 사용되었으나, 최근 물성의 향상 및 상아질 결합제의 발달로 심미수복이 필요한 여러 부위에 이용되고 있다. 반직접법을 이용한 레진 인레이는 와동의 크기가 너무 크거나 직접 수복이 곤란한 경우 사용될 수 있으며, 어린 환자의 영구구치 수복시 적절한 비용으로 가급적 오랫동안 보철치료를 받지 않고 사용할 수 있도록 한다. 반직접법의 장점으로는 중합수축으로 인한 변연누출이 적고, 2차 중합을 통해 중합도가 증가하여 강도가 증가되며, 간접법시 필요한 기공실 과정이 불필요하여 1회의 내원으로 치료 가능하다는 것 등이 있다. 본 증례는 심미적 치료를 원하는 환자의 구치부 수복시 반직접법을 이용한 레진 인레이를 사용하여 양호한 치료결과를 얻었기에 이를 보고하는 바이다.

• Restorative Dentistry and Endodontics
• /
• 제21권2호
• /
• pp.642-651
• /
• 1996

The purpose of this study was to evaluate the relationship between monomer compositions and the changes in the degree of conversion in the various layers of composites after additional heat curing. Four types of composites and 3 types of inlay ovens were used in this study. Composite was placed in a 4-mm thick teflon mold, and light cured from the top for 60 seconds. Ten samples were prepared for each composite ; 5 of these were additionally heat cured in an inlay oven as the manufacturer recommended. After light curing or light and heat curing, the samples were sectioned into four parts and assigned to groups A, B, C, or D according to their distance from the light source. These sections were then thinned to 50-$70{\mu}m$, and these wafers were analyzed with a Fourier Transform Infrared Spectrometer(FI-IR) to determine the degree of conversion. A standard baseline technique was used to calculate the degree of conversion. $^{13}C$ NMR spectra of bis-GMA, TEGDMA and bis-EMA, were acquired using a Varian Gemini spectrometer operated at 200 MHz. $CDCl_3$ solvent was used for qualitative analysis. The degree of conversion was affected by bis-GMA : TEGDMA ratio but it seemed to be also affected by other factors. When the composites were heat cured, significant increases in the degree of conversion were noted throughout the samples, but the amount of increase differed between materials. Thus, clinical performance of a heat-treated composite inlay may be different depending on materials.

• 한국결정성장학회지
• /
• 제31권6호
• /
• pp.247-257
• /
• 2021

본 연구는 오토클레이브 양생시편이 예상과 달리 초기강도는 잘 발현되지 않는 반면, 수중에 장기 침지할 경우 압축강도가 향상되는 현상을 규명하기 위해 시작되었다. 증류수 및 알칼리 용액에 침지하였고, 세 가지 양생방법이 시도되었다. 알칼리용액에 침지할 경우 증류수 침지 시편이 추가적인 지오폴리머 반응에 의해 보다 더 높은 압축강도를 가질 것으로 예상하였으나, 실제로 추가적인 지오폴리머 반응에 의해 생성된 결정립들과 알칼리골재 반응에 의한 시편의 팽창 때문에 21일 침지 후 침지용액에 의한 압축강도의 변화는 크게 나타나지 않은 것으로 사료되었다. 지오폴리머의 수중 및 알칼리용액 내 장기공용성을 확보하기 위해서는 오토클레이브를 이용하여 양생 후 21일 이상 수중 침지를 시키면서 숙성(aging) 시키는 것이 바람직 한 것으로 결론지을 수 있었다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.861-865
• /
• 2000

During the placement of concrete in cold weather, there are serious problems due to frozen concrete in the early stage. These adverse effects prevent the hardening of concrete. There are special mixing, handling, placement and crying to minimize problems. Heat crying and sheet curing have been used in crying steps in order to reduce problems. However, these curing methods are not efficient because it is hard to obtain the good quality and strength of concrete, and moreover, it needs additional works for curing. In this study, we evaluate the application of cold weather concrete by the dose antifreezing admixture in concrete mix design. Because it is easy to handle inconstruction site and improve the quality of concrete. As the result of this paper is to present a successful case for the practical use of cold weather concrete.

• 대한소아치과학회지
• /
• 제29권3호
• /
• pp.328-336
• /
• 2002

본 연구의 목적은 일반 halogen lamp 광조사기와 비교하여 plasma xenon arc lamp 광조사기의 광중합 능력을 평가하기 위한 것이다. 7mm의 내경과 1mm, 2mm, 3mm 두께를 갖는 레진 시편을 aluminum 주형상에서 제작하여 plasma xenon arc lamp 광조사기는 2초, 3초, 6초, halogen lamp 광조사기는 20초, 40초, 60초 동안 광조사한 후 Raman spectroscopy를 이용하여 레진 시편 표면과 후면의 중합률을 측정하였다. 표면 중합률은 광조사 시간이 증가함에 따라 halogen lamp 광조사기와 plasma xenon arc lamp 광조사기 모두에서 유의성있게 증가하였으며 전반적인 중합률은 halogen lamp 광조사기에서 더 높았으나 plasma xenon arc lamp 광조사기와 유의한 차이는 없었다. 광조사 시간이 증가함에 따라 halogen lamp 광조사기의 경우 후면 중합률은 모든 두께에서 점차 증가하였으나 1.2mm 두께에서는 유의한 차이가 없었으며 plasma xenon arc lamp 광조사기로 중합한 경우에는 모든 두께에서 조사시간이 증가할수록 중합률은 유의성있게 증가하였다. 이상의 결과로 plasma xenon arc lamp 광조사기의 강한 광도가 광조사 시간의 감소를 완전히 보상하지는 못하는 것으로 판단되므로 plasma xenon arc lamp 광조사기로 광중합 복합레진을 중합할 경우 2mm이내의 적층 충전이 요구되며 또한 제조회사가 제시한 조사 시간보다 추가적인 광조사가 필요할 것으로 판단된다.

• The Journal of Advanced Prosthodontics
• /
• 제5권4호
• /
• pp.464-470
• /
• 2013

PURPOSE. The aim of this Fourier transform infrared (FTIR) spectroscopic study was to measure the degree of conversion (DC) of dual-cured resin cements light-irradiated through zirconia ceramic disks with different thicknesses using various light-curing methods. MATERIALS AND METHODS. Zirconia ceramic disks (KT12) with three different thicknesses (1.0, 2.0, and 4.0 mm) were prepared. The light transmittance of the disks was measured using ultraviolet visible near-infrared spectroscopy. Four different light-curing protocols were used by combining two curing light modes (Elipar TriLight (standard mode) and bluephase G2 (high power mode)) with light-exposure times of 40 and 120 seconds. The DCs of the two dual-cured resin cements (Duo-Link and Panavia F2.0) light-irradiated through the disks was analyzed at three time intervals (3, 7, and 10 minutes) by FTIR spectroscopy. The data was analyzed using repeated measures ANOVA (${\alpha}$=.05).Two-way ANOVA and Tukey post hoc test were used to analyze the 10 minute DC results. RESULTS. The 1.0 mm thick disk exhibited low light transmittance (<25%), and the transmittance decreased considerably with increasing disk thickness. All groups exhibited significantly higher 10 minute DC values than the 3 or 7 minute values (P<.05), but some exceptions were observed in Duo-Link. Two-way ANOVA revealed that the influence of the zirconia disk thickness on the 10 minute DC was dependent on the light-curing methods (P<.001). This finding was still valid even at 4.0 mm thickness, where substantial light attenuation took place. CONCLUSION. The curing of the dual-cured resin cements was affected significantly by the light-curing technique, even though the additional chemical polymerization mechanism worked effectively.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.172-175
• /
• 2001

The co-cured Joining method, which is regarded as an adhesively bonded Joining method, is an efficient joining technique because both curing and bonding processes for the composite structures can be achieved simultaneously. It requires neither surface treatment onto the composite adherend nor an additional adhesive joining process because the excess resin, which is extracted from composite materials during consolidation, accomplishes the co-cured Joining process. Since the adhesive of the co-cured joint is the same material as the resin of the composite adherend, the analysis and design of the co-cured joint for composite structures are simpler than those of an adhesively bonded joint, which uses an additional adhesive. In this paper, effects of the manufacturing parameters, namely surface roughness, stacking sequence of the composite adherend, and manufacturing pressure in the autoclave during curing process, on the tensile load bearing capacity of the co-cured single lap joint will be experimentally investigated.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.232-235
• /
• 2002

Recently developed liquid silicone rubber (LSR) can be cured by platinum catalyzed additional hydrosilylation mechanism and has the advantage of no byproduct compared to traditional millable peroxide curing silicone rubber. We investigated the characteristics of dielectric breakdown of silicone rubber and adhesion properties between semi-conductive LSR and insulating LSR for high voltage application of pre-molded joint (PMJ). In order to understand the dielectric breakdown characteristics, we used the sheet samples and the paired type rogowski insert electrode system. The breakdown strength and adhesion strength of LSR (E-3) were superior to those of several silicone rubbers. Adhesion strength could be improved by curing at high temperature without post-curing process or enhanced by post-curing process. When LSR (E-3) was cured at $(150^{\circ}C{\times}10min$ semi-conductive )${\times}$ ($175^{\circ}C{\times}10min$ insulation), it showed the high breakdown strength with low standard deviation, and good adhesion strength. In this results, we could apply this process to the fabrication of PMJ without post-curing.

• 보존과학회지
• /
• 제32권2호
• /
• pp.223-234
• /
• 2016

2액형 에폭시 수지는 문화재 보존처리에 매우 광범위하게 사용되고 있으나 사용 시 주제와 경화제의 배합비율에 따라 경화특성, 기계적 강도, 화학 구조 등이 달라질 수 있고 대상 문화재의 안정성에 영향을 미칠 수 있다. 설문조사 결과, 보존처리 실무자들은 소량의 에폭시수지를 눈대중으로 혼합하거나 가사시간을 줄이기 위해 인위적으로 경화제를 과량 첨가하는 경우가 있는 것으로 조사되었다. 이 연구에서는 속경화형 2종과 일반경화형 2종의 에폭시수지를 대상으로 주제에 대한 경화제의 비율을 0.25~4배로 설정하여 각 경우의 경화특성, 기계적 강도, 화학 작용기를 분석하였다. 그 결과 속경화형 에폭시수지는 경화제가 0.5~2배일 때 높은 반응열과 함께 경화반응이 빠르게 나타났으며, 경화제 비율이 제조사에서 공시된 정비율보다 적을 때 더 높은 기계적 강도가 나타났고 에폭시의 가교결합도 활발히 일어난 것으로 관찰되었다. 일반경화형 에폭시수지는 대부분 경화반응열이 낮고 느린 반응속도로 경화가 진행되며, 경화제가 정비율 이하에서 가장 높은 기계적 강도를 나타냈다. 그러나 경화제 비율이 2배 이상 일 때는 경화속도가 매우 느려지고 접착강도도 낮아지는 것으로 나타났다. 따라서 배합비가 정비율 이하에서는 비교적 빠른 반응속도와 유사한 기계적 강도를 나타내는 반면 정비율 이상에서는 물성이 급격하게 저하되므로 구현하고자 하는 성능에 영향을 미칠 수 있을 것으로 판단된다.

• Fibers and Polymers
• /
• 제1권2호
• /
• pp.116-121
• /
• 2000

It has been considered that malic acid, $\alpha$-hydroky succinic acid, could not form crosslinks in the cellulosic materials unless activated by other polycarboxylic acids such as butanetetracarboxylic acid or citric acid because there are only two carboxylic acids per molecule available fur the formation of one anhydride intermediate. However we found that the dicarboxylic malic acid with sodium hypophosphite catalyst without the addition of other crosslinkers was able to improve wrinkle resistance of cotton up to $294^{\circ}$(dry WRA) and $285^{\circ}$ (wet WRA), which is a measure of crosslinking level in cotton. $^1$H FT-NMR, FT-IR and GPC analysis indicated the in-situ formation of an trimeric $\alpha$, $\beta$-rnalic acid with a composition of 1:3 through the esterification between hydroxyl group and one of carboxylic groups in malic acid during curing. The crosslinking of cotton was attributed to the trimeric $\alpha$, $\beta$-malic acid, a tetracarboxylic acid, which can form two anhydride rings during curing. The influence of crosslinking conditions such as concentrations of malic acid and catalyst, pH of the formulation bath, and curing temperature were investigated in terms of imparted wrinkle resistance and whiteness. The addition of reactive polyurethane resin in the formulation slightly increased the mechanical strength retention of crosslinked fabric coupled with additional increase in wrinkle resistance.