• Journal of the Korean institute of surface engineering
• /
• v.48 no.2
• /
• pp.56-61
• /
• 2015

In this study, the wear performance of manganese phosphate coating on SM45C with addition agent of Tartaric acid and Citric acid were investigated. The Surface morphology of manganese phosphate coating was examined by Scanning Electron Microscope (SEM) and Energy Dispersive X-ray spectroscopy (EDS). It is found that Mn, P, Fe, O and C. The crystal structure and thee composition was analysis and determined by using XRD. The XRD results indicated that manganese phosphate coatings are mainly composed of $(Mn,Fe)_5H_2(PO_4)_44H_2O$ and consists of a lot of close packed lump crystalline. Based on the time dependence of morphology and the weight of manganese phosphate coating, it shows that the phosphating process mainly includes three stages: corrosion of the substrate, creation and growth of phosphate crystal nucleus and thickening of manganese phosphate coating. The wear tests were performed in a ball on disc apparatus as per ASTM G-99 Standard. It was showed that the initial wear was quite high followed by low sludge.

• Elastomers and Composites
• /
• v.52 no.3
• /
• pp.187-193
• /
• 2017

In this study, the effect of the cure, mechanical properties, and oil resistance of NBR (acrylonitrile-butadiene rubber)/peroxide compounds were investigated for various co-agents. NBR compounds were characterized using a swelling test, a rheometer (MDR), and a compression set test. Mechanical properties were tested with original compounds, heated in air and exposed to the ASTM No.1, IRM 903 oil. NBR compounds were prepared using peroxide as the crosslinking agent. Trimethylolpropane trimethacrylate (TMPTMA), triallyl isocyanurate (TAIC), and 1,2-polybutadiene (HVPBD) were used as co-agents. The NBR compounds containing TMPTMA and HVPBD lowered the scorch time, while the addition of TAIC did not significantly change the scorch time. NBR compounds containing TMPTMA increased the crosslinking density, while the addition of TAIC and HVPBD lowered the crosslinking density. Moreover, the addition of TMPTMA improved the oil resistance of the NBR compound.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.1
• /
• pp.1-6
• /
• 2015

Amino-carboxyl acid as a complexing agent in acid copper sulfate solution was utilized to improve the adhesion of immersion copper layer for steel wire. According to the tape test results, regardless of alloy composition of the wire, the adhesion of immersion copper layer was improved with the addition of amino-carboxyl acid. The incorporation of H and Fe in the plating layer was analyzed by TOF-SIMS. The H and Fe were detected at the entire coating layer without any addition of amino-carboxyl acid. However, with addition of amino-carboxyl acid, the H and Fe were scarcely detected at the coating layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.779-785
• /
• 2012

The epoxy/micro-and nano-mixed silica composites(EMNC) systems were prepared and the AC insulation breakdown strength was evaluated. Glass transition temperature (Tg) and crosslink density were also measured by dynamic mechanical analyzer(DMA) in order to correlate them with the electrical and mechanical properties, and the effect of silane coupling agent on the electrical properties was also studied. Electrical properties and crosslink density of epoxy/micro-silica composite were noticeably improved by addition of nano-silica and silane coupling agent, and the highest breakdown strength was obtained by addition of 0.5~5 phr of nano-silica and 2.5 phr of silane coupling agent, and the highest tensile and flexural strength were obtained by addition of 2.5 phr of nano-silica.

• Textile Coloration and Finishing
• /
• v.31 no.2
• /
• pp.118-126
• /
• 2019

This study aims to investigate the effect of polytriazolesulfone(PTS) addition on fracture toughness of diglycidyl ether of bisphenol A(DGEBA) and 4,4'-diaminodiphenylsulfone(DDS). Various amounts of PTS were added to DGEBA/4,4'-DDS in diazide and dialkyne monomer forms and polymerized during the epoxy curing process. Fracture toughness(K1C), tensile properties and thermal stability of the PTS added epoxy resin were evaluated and compared with those of PES, the conventional high Tg toughening agent, added epoxy resin. Fracture toughness of the PTS added epoxy resin was dramatically improved up to 133%, as the amount of PTS added increased, whereas that of the PES added epoxy resin was improved by only 67%. The tensile strength of PTS added DGEBA/4,4'-DDS was similar to the epoxy resin without PTS and tensile modulus was improved by 20%. And thermal stability of the PTS added epoxy resin was improved up to 14%. Therefore, PTS addition to DGEBA/4,4'-DDS, as a toughening agent, is very effective way to improve its fracture toughness without any lowering in other properties.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.4 s.107
• /
• pp.77-82
• /
• 2004

Expression-deliquoring tests using three types of paper sludges (tissue, newsprint, and paperboard) as deliquoring agent were carried out in order to investigate the effects of sludge dosage and pressure on the expression-deliquoring of slurry. The addition of deli­quoring agent causes expression-deliquoring of slurry to be faster than would be the case without the deliquoring agent. In case of the tissue sludge, the highest compression rate was achieved when $5\%$ of deliquoring agent was added, while in cases of the news­print and the paperboard sludge, $7\%$. Compression rate was increased as pressure increases. Porosity was decreased as pressure increases. The lowest porosity was observed when $5\%$ of tissue sludge was added. When compared the weight of cake where deliquoring agent was not added and the weight of cake that was fastest expression-deliquoring, there was about $17.5\%$ of the weight reduction

• Journal of environmental and Sanitary engineering
• /
• v.18 no.4
• /
• pp.1-5
• /
• 2003

For studying out the method of the effective purification of waste waters such as dying, paper pulp and plating wastewater, we measured the COD removal efficiency, color and turbidity of those pollutants by the physical and chemical method using the Inorganic Coagulating Agent (CM, RM) and a High Voltage Generator. The COD removal efficiency measured when applying the Inorganic Coagulating Agent (CM, RM) was mush higher than that using the Existing Coagulating Agent In addition to, when using those two methods above mentioned at the same time, both the COD removal efficiency and the reduction-effect of the inserting quantities of Coagulating Agent were higher than those were used singly. The system using both an Inorganic Coagulating Agent and a High Voltage Generator will be useful in various fields of wastewater treatment.

• Journal of Information Processing Systems
• /
• v.6 no.2
• /
• pp.185-196
• /
• 2010

This paper proposes a personal information protection model that allows a user to regulate his or her own personal information and privacy protection policies to receive services provided by a service provider without having to reveal personal information in a way that the user is opposed to. When the user needs to receive a service that requires personal information, the user will only reveal personal information that they find acceptable and for uses that they agree with. Users receive desired services from the service provider only when there is agreement between the user's and the service provider's security policies. Moreover, the proposed model utilizes a mobile agent that is transmitted from the user's personal space, providing the user with complete control over their privacy protection. In addition, the mobile agent is itself a self-destructing program that eliminates the possibility of personal information being leaked. The mobile agent described in this paper allows users to truly control access to their personal information.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.1
• /
• pp.25-38
• /
• 1998

The developing agent is the materials which first acts on silver grain and make it into metallic silver by reducing reaction. There are several types in developing agent, and according to Lumiere-Andresen principle, substitution product which has amino or hydroxyl group in benzen nucleus has a developing power, but all reduing substances are not in used. In the developing effect, not only the role of developing agent but also that of assistant materials are important. But in this work, we have studied effect, change by lith developing agent which require high contrast image. We made an developing experiment after having manufactured developing solution used hydroquinone and another developing agents like chlorohydroquinone, pyrocatechol and pyrogallol as developing agent. And we added that did in addition of diethanolamine and ascorbic acid, and then we examined the possibility of use.

• Macromolecular Research
• /
• v.10 no.2
• /
• pp.127-134
• /
• 2002

Microporous polypropylene hollow fiber membrane was fabricated from isotactic polypropylene-soybean oil system by melt spinning process. Addition of nucleating agent accelerated the crystallization rate and elevated the crystallization temperature. Nucleating agent increased the number of nuclei and spherulites, which offered more inter-spherulitic amorphous sites for stretching. Benzoic acid, adipic acid, and dibenzylidene sorbitol were selected as nucleating agents, and their characteristics and effects were investigated by thermal and optical analyses. Spherulite growth and micropore formation characteristics were correlated with the kind of nucleating agent. Benzoic acid and adipic acid showed the remarkable nucleating effect, while dibenzylidene sorbitol was less effective than those. Nucleating agents also helped the sample have uniform microporous structure. Increase of nucleating agent composition enhanced the nucleation effect to some extent. Nucleating agents played very important roles in enhancing the membrane porosity and water flux.