• Title/Summary/Keyword: Active zone

Search Result 448, Processing Time 0.032 seconds

Active Sound Control Approach Using Virtual Microphones for Formation of Quiet Zones at a Chair (좌석의 정음공간 형성을 위한 가상마이크로폰 기반 능동음향제어 기법 연구)

  • Ryu, Seokhoon;Kim, Jeakwan;Lee, Young-Sup
    • Transactions of the Korean Society for Noise and Vibration Engineering
    • /
    • v.25 no.9
    • /
    • pp.628-636
    • /
    • 2015
  • In this study, theoretical and experimental analyses were performed for creating and moving the zone of quiet(ZoQ) to the ear location of a sitter by using active sound control technique. As the ZoQ is actively created at the location of the error microphone basically with an active sound control system using an algorithm such as the filtered-x least mean square(FxLMS), the virtual microphone control(VMC) method was considered to move the location of the ZoQ to around the sitter`s ear. A chair system with microphones and loudspeakers on both sides was manufactured for the experiment and thus an active headrest against the swept narrowband noise as the primary noise was implemented with a real-time controller in which the VMC algorithm was embedded. After the control experiment with and without the VMC method, the location variation of the ZoQ by analyzing the error signals measured by the error and the virtual microphones. Therefore, it is observed that the FxLMS with the VMC technique can provide the re-location of the ZoQ from the error microphone location to the virtual microphone location. Also it is found that the amount of the attenuation difference between the two locations was small.

Modified FxLMS Algorithm for Active Noise Control and Its Real-Time Implementation

  • Mu, Xiangbin;Ko, JinSeok;Rheem, JaeYeol
    • Journal of the Institute of Electronics and Information Engineers
    • /
    • v.50 no.9
    • /
    • pp.172-176
    • /
    • 2013
  • This paper presents a modified filtered-x least mean square (FxLMS) algorithm to improve the stability of active noise control (ANC) system in realistic environment. A real-time ANC system employing modified FxLMS is designed and implemented on digital signal processor (DSP) board. The ANC system is evaluated for cancelling various tonal frequency noises in the range from 100 to 500 Hz and the performance is measured in terms of sound pressure level (SPL) attenuation. Experiment results show that a quiet zone with maximum 20 dB SPL attenuation can be generated around the location of error microphone.

Study on active vibration control based on wave viewpoint using the longitudinal wave separation method (종파 분리 방법을 이용한 파동 관점의 능동 진동 제어)

  • Jung, Byung-Bo;Park, Young-Jin;Park, Youn-Sik
    • Proceedings of the Korean Society for Noise and Vibration Engineering Conference
    • /
    • 2007.05a
    • /
    • pp.928-933
    • /
    • 2007
  • In this research, we investigated active vibration control based on wave-viewpoint using the longitudinal wave separation method. The control strategy is the one of active vibration control technique for generating vibration reduced zone and uses wave information including the directivity as the cost function. In order to get the wave information from the measured values, we proposed and examined the time-domain longitudinal wave separation method proper to real time application like active vibration control. Using the proposed method, we examine the performance and feasibility of active vibration control based wave view-point through the simulation. The related experimental verification and application is going to be expected in a near future.

  • PDF

A study on the PAL according to thermal characteristic of building skin and perimeter zone depth (건물 외피의 열특성과 외주부 깊이에 따른 PAL에 관한 연구)

  • Kim, Ji-Hye;Kim, Hwan-Yong
    • Journal of the Korean Solar Energy Society
    • /
    • v.30 no.2
    • /
    • pp.33-38
    • /
    • 2010
  • The perimeter zone is space which receives a significant effect of ambient condition, it is necessary to improve the thermal performance in order to building energy saving. For this reason, a lot of study about the active approach is being performed, such as perimeter-less air conditioning system. But the performance of the perimeter zone is necessary to improve, through the passive approach. Therefore, the purpose of this study is to provide basic materials of energy-saving design of perimeter zone, based of the PAL that simulation changing the thickness of insulation and the rate of windows.

Loop Suture Technique for Flexor Digitorum Profundus Tendon Repair in the Insertion Site (고리 봉합법을 이용한 심부 수지 굴건 종지부에서의 건봉합)

  • Lee, Kyu-Cheol;Lee, Dong-Chul;Kim, Jin-Soo;Ki, Sae-Hwi;Roh, Si-Young;Yang, Jae-Won
    • Archives of Plastic Surgery
    • /
    • v.37 no.5
    • /
    • pp.650-658
    • /
    • 2010
  • Purpose: In the case of repair for far distal parts of FDP (Flexor digitorum profundus) division, the method of either pull-out suture or fixation of tendon to the distal phalanx is preferred. In this paper, the results of a modified loop suture technique used for the complete division of FDP from both zone 1a and distal parts of zone 1b in Moiemen classification are presented. Methods: From July 2006 to July 2009, the modified loop suture technique was used for the 10 cases of FDP in complete division from zone 1a and distal parts of zone 1b, especially where insertion sites were less than 1 cm apart from a tendon of a stump. In a suture technique, a loop is applied to each distal and proximal parts of tendon respectively. Core suture of 2-strand and epitendinous suture are done with PDS 4-0. Out of 10 patients, the study was done on 6 patients who were available for the followup. The average age of the patients was 49.1 years (in the range from 26 to 67). 5 males and 1 female patients were involved in this study. There were 3 cases with zone 1a and distal parts of zone 1b. The average distance to the distal tendon end was 0.6 cm. There were 5 cases underwent microsurgical repair where both artery and nerve divided. One case of only tendon displacement was presented. The dorsal protective splint was kept for 5 weeks on average. The results of the following tests were measured: active & passive range of motion, grip strength test, key pinch and pulp pinch test. Results: The follow-up period on average was 11 months, in the range from 2 to 20 months. There was no case of re-rupture, but tenolysis was performed in 1 cases. In all 6 cases, the average active range of motion of distal interphalangeal joint was 50.8 degree. The grip strength (ipsilateral/contralateral) was measured as 88.7% and the pulp pinch test was 79.2% as those of contralateral side. Flexion contracture was presented in 2 cases (15 degree on average) and there was no quadrigia effect found. Conclusion: Despite short length of tendon from the insertion site in FDS rupture in zone 1a and distal parts of zone 1b, sufficient functional recovery could be expected with the tendon to tendon repair using the modified loop suture technique.

Application of BIPV System Functioned as Solar Collector (태양열 집열기 기능을 갖는 BIPV 시스템의 응용)

  • Min, Sung-Hye;Suh, Seung-Jik
    • Proceedings of the SAREK Conference
    • /
    • 2006.06a
    • /
    • pp.953-958
    • /
    • 2006
  • Perimeter zone has been reinforced by active systems, such as fan-coil units, because it causes an increase in heating and cooling loads, dew condensation in winter, or discomfort with cold-draft to residents in buildings, through poor insulation by light-weighed skin due to progressing multi-storied buildings and skyscrapers. However, because these active systems raise Its capacity so that fossil fuel is used as much as they are added, and ultimately, greenhouse effect is urged, we proposed BIPV system functioned as solar collector which can substitute active system. As an early stage, heat balance equation in steady-state by Fortran was used not only for pre-heating effect and electric power capacity during the day in winter, but also for electric power capacity during day in slimmer and sky radiation effect during night in summer. Especially, we should have considered shading on PV, since even a little bit of it makes the efficiency too low for the PV to work. Still, when the flux of pre-heated air was increased to make air-barrier, its temperature was not enough to make it because the speed of heat exchange was too fast to warm up the air, thus the capacity to meet the condition was evaluated, and electric power from PV was made used for it.

  • PDF

A Study on Application & Evaluation of Riverbed Techniques for the Formation of Hyporheic Zone (하상간극수역의 형성을 위한 하상공법의 적용과 평가)

  • Choi, Jungkwon
    • Journal of the Korean Society of Environmental Restoration Technology
    • /
    • v.16 no.6
    • /
    • pp.119-133
    • /
    • 2013
  • The purpose of this study is to develop riverbed techniques to activating ecological function of hyporheic zone. Hyporheic zone maybe simply defined as an active eco-tone between surface water and groundwater, which facilitates to exchange water, nutrients and aquatic habitat occur in response to variation in discharge and bed geomorphology. The aim of this study is to evaluate the effectiveness of an applied riverbed technique for two years since its installation in the hyporheic zone. The experimental riverbed technique has been implemented on Anyang stream penetrating Anyang city in Gyunggi province. The dimension of the installed structure is 5.0 m in width, 46 m in length. Bottom layer is filled with rip-rap covered with gabion. After the implementation of the technique, the study conducts follow-up monitoring in two years of between 2011 and 2012. The results of follow-up monitoring for two years are as follows:1) In Hydro geomorphic process, the riverbed technique maintains hydraulic stability despite of several flood events in 2011, 2012. 2) After transformation to form pool-and-riffle habitat, for aquatic community composed of freshwater fish, macro invertebrate, and attached algae, the species diversity and population gradually increased. 3) The riverbed technique achieved desired effect on enhancement of ecological function in hyporheic zone.

A Study on the Attention Concentration Properties in Convergent Exploration Situations in Cafe Space - Focusing on Gaze and Brain wave Data Analysis - (카페공간에 대한 수렴적 탐색상황에서의 주의집중 특성의 분석 방법에 관한 연구 - 선택적 주시데이터에 의한 뇌파 데이터 분석을 중심으로 -)

  • Kim, Jong-Ha;Kim, Ju-Yeon;Kim, Sang-Hee
    • Korean Institute of Interior Design Journal
    • /
    • v.25 no.2
    • /
    • pp.30-40
    • /
    • 2016
  • This study analyzed the attention concentration tendencies of one(1) subject who showed convergent exploratory acts actively through the gaze-brainwave measurement experiment of cafe space images and our research findings are as follows. First, the areas of interest (AOIs) that the subject gazed visually by paying attention to it and concentrating on it at a cafe space include counter&menu area, sign area, partition area, image wall area, stairs area, and movable furniture area, and built-in furniture area: seven areas in total. Second, conscious gaze frequency appeared the highest in counter&menu area, and conscious gaze appeared more later than in initial times. Third, conscious gaze pattern was divided into the zone that explored various areas dispersely (distributed exploratory zone) and the zone that explored between particular areas concentratedly (intensive exploratory zone). Fourth, as a result of analyzing the brainwave attention concentration, it was found that the attention concentration in prefrontal lobe (Fp1, Fp2) and frontal lobe (F3, F4) rose to a higher level in the zone of 15 to 16 seconds and this time zone was considered to be a zone where gazing at counter&menu area was very active. In addition, the attention concentration appeared higher in the initial zone than in the later zone, among the entire experimental time zones. Finally, as a result of analyzing the changes in activation by brain portion of the SMR wave expressed when maintaining the arousal and attention concentration, it was found that the right prefrontal lobe and the frontal lobe became activated in the time zone when the intensive exploration of "counter&menu area" and "movable furniture${\leftrightarrow}$built-in furniture area" had occurred and the time zone when the intensive exploration of "image wall${\leftrightarrow}$partition area" and "counter&menu${\leftrightarrow}$sign area" had occurred.

Simulation of Non-Detection Zone using AFD Method applied to Utility-Connected Photovoltaic Systems for a Variety of Loads (다양한 부하에 따른 계통연계형 태양광발전 시스템에 적용된 AFD 기법의 단독운전 불검출영역 시뮬레이션)

  • Ko, Moon-Ju;Choy, Ick;Choi, Ju-Yeop;Won, Young-Jin
    • 전자공학회논문지 IE
    • /
    • v.43 no.2
    • /
    • pp.63-69
    • /
    • 2006
  • Islanding phenomenon of utility-connected PV power conditioning systems(PV PCS) can cause a variety of problems and must be prevented. If the real and reactive powers supplied by PV PCS are closely matched to those of load, islanding detection by passive methods becomes difficult. The active frequency drift(AFD) method, called the frequency bias method, enables islanding detection by forcing the frequency of the voltage in the islanding to drift up or down. In this paper, non-detection zone(NDZ) of AFD is analyzed for the islanding detection method of utility-connected PV PCS by simulation tool PSIM.

Analysis of Global Volcanic Activity During 2019 (2019년 지구에서 분화한 화산 활동 분석)

  • Yun, Sung-Hyo;Ban, Yong-Boo;Chang, Cheolwoo;Lee, Jeonghyun
    • Korean Journal of Mineralogy and Petrology
    • /
    • v.33 no.4
    • /
    • pp.451-462
    • /
    • 2020
  • There are 82 volcanoes active during the 48 weeks of 2019 (January 30 to December 31, 2019; USGS data) Approximately 80~90 volcanoes are active on the Earth for a year. More than 91% of these volcanoes are took place in the circum-Pacific volcanic belt, which is commonly called 'Ring of Fire'. This status coincides with the distribution maps of active volcanoes on the earth: about 80 percent on subduction zone of the convergent plate boundaries; 15 percent on divergent plate boundaries; 5 percent on intra-plate zone. Typically five volcanoes are most active during the survey period (48 weeks); Dukono (Halmahera, Indonesia) 48 times, Aira (Kyushu, Japan) 47 times, Ebeko (Paramushir Island, Russsia) 46 times, Merapi (Central Java, Indonesia) 37 times, Krakatau (Indonesia) 33 times. The comparison of volcanic activity between 2018 and 2019 showed no significant difference. It is assumed that volcanic activity remains stable.