• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.327-330
• /
• 2003

We present the fabrication and measured performance of a wavelength tunable Butt coupled DBR-LD. An average coupling efficiency between active layer and passive waveguide layer was measured over 85％per facet, and the average threshold current was 21 ㎃ for the waveguide integrated DBR laser. High output power of Butt coupled DBR-LD was obtained over 25 ㎽. As high as 25 ㎽ of output power was achieved by the butt coupled method. The maximum wavelength tuning range is about 7.4 nm, and the side mode suppression ratio was more than 40 ㏈ using 1.3 ${\mu}{\textrm}{m}$ InGaAsP waveguide layer.

• Current Optics and Photonics
• /
• v.3 no.2
• /
• pp.105-110
• /
• 2019

The visible-light communication (VLC) system is a promising candidate to fulfill the present and future demands for a high-speed, cost-effective, and larger-bandwidth communication system. VLC modulates the visible-light signals from solid-state LEDs to transmit data between transmitter and receiver, but the broadcasting and the line-of-sight propagation nature of visible-light signals make VLC a communication system with a limited operating range. We present a novel architecture to increase the operating range of VLC. In our proposed architecture, we guide the visible-light signals through the fiber and amplify the dissipated signals using visible-light fiber amplifiers (VLFAs), which are the most important and the novel devices needed for the proposed architecture of the VLC. Therefore, we design, analyze, and apply a VLFA to VLC, to overcome the inherent drawbacks of VLC. Numerical results show that under given constant conditions, the VLFA can amplify the signal up to 35.0 dB. We have analyzed the effects of fiber length, active ion concentration, pump power, and input signal power on the gain and the noise figure (NF).

• Korean Journal of Optics and Photonics
• /
• v.35 no.3
• /
• pp.95-106
• /
• 2024

In the 21st century, white light-emitting diodes (LEDs) are widely used as backlighting for liquid crystal displays and as a light source for general illumination. However, white LEDs used in lighting often use a single yellow phosphor on top of a blue LED chip, which lacks the ability to reproduce natural colors in objects under conventional illumination accurately. Recently, researchers have been actively working on realizing high color-rendering lighting by incorporating red quantum dots to improve the spectrum in the long-wavelength band, which is deficient in conventional white LEDs. In particular, how to develop and apply remote quantum dot components to ensure long-term reliability is currently under active research. This paper introduces recent research on remote quantum dot components and the current status of developing high color-rendering lightings with them. Especially, we focus on various factors that are important to consider in optimizing the optical structure of the quantum dot components and discuss the future directions and prospects of research for high color-rendering lighting technology.

• Journal of Korean Ophthalmic Optics Society
• /
• v.4 no.2
• /
• pp.129-133
• /
• 1999

For the myopia eyes of the people which are ametropia, the classified distribution has showed % for the simple myopic, 50% for the compound myopic astigmatism, 15% for the simple myopic astigmatism and 19% for the mixed astigmatism. The myopic ametropia for the both eyes has the distribution of 35% for -0.50D~-2.00Dptr, 54% for -2.00~6.00Dptr, and 11% for over -6.00Dptr. The classifying distribution for the age for the myopic ametropia was 54% for 15~20, 22% for 21~40, 14% for 41~60 and 10% for 61. The occupational distribution for the myopic ametropia has showed 61.5% for the student(Middle, High, College), 13.5% for the office worker, and 15% for the house wives as well as the small business. The hour affecting the refraction most for a day was after P.M. 7 which recorded 45% as the highest value. The reason is that the myopia degree decreases in the morning as the cornea flats and the situation is reversed in the afternoon so that there is a difference of Sph -0.50D and as getting darker the refraction degree of the light coming through the enlarged pupil refraction around the cornea is high. For the seasons the highest myopic degree has been recorded for 68% in the summer due to the shortage of nutrition and the climination inside the body by the exhaustion of sweat. In the blood types A and B are distributed closely as 34% and more active man with O has recorded higher myopic degree than woman. However woman showed higher accommodation power than man regardless the blood types. In the characteristic factors of myopic eye, the character feels fatigue easily has showed the distribution for 42% which is the highest and it could be classified largely by two the.

• Journal of Korean Ophthalmic Optics Society
• /
• v.20 no.1
• /
• pp.15-23
• /
• 2015

Purpose: This study was investigated consumers' and optometrists' perception about spectacle frame in Busan and Ulsan to find on the right progress direction for conversion of spectacle frame into medical devices. Methods: 137 consumers surveyed in Busan and Ulsan and 100 optometrist surveyed in 'Busan continuing education of optometrist' filled in a questionnaire, then we compared and analyzed the results. Results: The 79% (108 people) of consumers and 94% (94 people) of optometrists agreed to conversion into medical devices of spectacle frame. The reason was shown that the consumer expected to improve the optometrist reliability and the optometrist expected to improve the optometrist professionalism. While, the 21% (29 people) consumer and 6% (6 people) optometrist opposed to conversion of spectacle frame into medical devices. The reason was revealed that the consumers were concerned about increase of medical insurance cost and the optometrists were concerned about that the spectacle frames can also be sold by medical device stores, not only by optical shops. Conclusions: The result of the survey was shown that the most of consumers and optometrists in Busan and Ulsan agreed on perception toward a conversion of spectacle frame into medical devices. But, we are considered that consumers' and optometrists' active attention and support are needed, with sequential implementation reflecting the concerns for this.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.518-523
• /
• 1999

In thi, study, we made experiments to fonn a mesa shape by meltback method with various concentration of solutions and found that unsaturated (20%) InGaAsP (1.55 !-tm) solution at a growth temperature was the most suitable for the formation of a mesa ,hape on the wafer which has an InGaAsP active layer and an InP cap layer on an n-InP substrate. It was difficult to form a proper mesa shape for the fabrication of PBH-LDs only by the meltback method; therefore, we fabricated PBH-LDs by forming the mesa shape with the meltback method after wet etching and by growing a current-blocking layer successively. As the electrical and optical charaleri,tiecs of MQW-PBH-LDs fabricated by above methods, when the cavity length was $300{\mu}m$, the threshold current was about 10 mA, internal quantum efficiency 82%, internal loss $9.2cm^{-1}$, and characteristic temperature was 65 K at $25~45^{\circ}C$ and 42 K at $45~65^{\circ}C$. /TEX>.

• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.3
• /
• pp.475-483
• /
• 2015

We propose a numerical scheme to simulate the time-domain echo signals at tracking radar for a realistic scenario where an EAD (expendable active decoy) and an airborne target are both in dynamic states. On various scenarios where the target takes different maneuvers, the trajectories of the EAD ejected from the target are accurately calculated by solving 6-DOF (Degree-of-Freedom) equations of the motion for the EAD. At each sampling time of the echo signal, the locations of the EAD and the target are assumed to be fixed. Thus, the echo power from the EAD can be simply calculated by using the Friis transmission formula. The returned power from the target can be computed based on the pre-calculated scattering matrix of the target. In this paper, an IPO (iterative physical optics) method is used to construct the scattering matrix database of the target. The sinc function-interpolation formulation (sampling theorem) is applied to compute the scattering at any incidence angle from the database. A simulator is developed based on the proposed scheme to estimate the echo signals, which can consider the movement of the airborne target and EAD, also the scattering of the target and the RF specifications of the EAD. For applications, we consider the detection probability of the target in the presence of the EAD based on Monte Carlo simulation.

• Korean Journal of Optics and Photonics
• /
• v.20 no.4
• /
• pp.217-222
• /
• 2009

In this paper, a low-cost hybrid-integrated tunable laser is realized using a polymer-ring resonator-based add/drop filter reflector and a reflective semiconductor optical amplifier. The add/drop filter reflector, composed of a double-ring resonator with different radii, can have characteristics of selective wavelength reflection and wide wavelength tuning with an aid of vernier effect derived from the radii difference. By hybrid-integrating the reflective semiconductor optical amplifier with the add/drop filter reflector, a tunable laser can be realized through an active alignment method. The hybrid laser exhibited a single mode lasing with side mode suppression ratio of 26 dB and full width half maximum of 0.03 nm. In addition, applying a low current as small as 25 mA onto electrodes over add/drop filter reflector, a wavelength tuning range of 17 nm could be obtained.

• Korean Journal of Optics and Photonics
• /
• v.18 no.2
• /
• pp.155-161
• /
• 2007

A new and simple method of 3-dimensional circuit modeling and analysis is proposed and verified experimentally for the first time by determining 3-dimensional current flow and 2-dimensional light distribution in blue InGaN/GaN multi-quantum well (MQW) light emitting diode (LED) devices. Circuit parameters of the LED consist of the resistance of the metallic film and epitaxial layer, and the intrinsic diode which represents the active region emitting the light. The circuit parameters are extracted from the transmission line model (TLM) and current-voltage relation. We applied the >> proposed method and extracted circuit parameters to obtain the light emission pattern in a top-surface emitting-type LED. The current spreading effect is analyzed theoretically and quantitatively with a variation of the resistance of metallic and epitaxial layers. The emitting-light distribution of the fabricated blue LED showed a good agreement with the analyzed result, which shows the dark emission intensity at the corner of the p-electrode.

• Korean Journal of Optics and Photonics
• /
• v.21 no.2
• /
• pp.74-81
• /
• 2010

A modeling methodology for the analysis of injection-locked Fabry-Perot laser diodes (FP-LDs), promising for cost-effective WDM-PON sources, is proposed. The time-domain large-signal model that is used is found to provide quite similar results to some experimental ones. With our methodology, we model characteristics of FP-LDs, such as influence of reflectivity at a facet and detuning on injection-locking. The eye diagram characteristics are also investigated. It is observed that the facet reflectivity at the injection side should be lower than 1% to provide stable operation in terms of good side-mode suppression ratio and independence from detuning between narrow-band injection noise and LD modes. It is also observed that good eye opening can be obtained for 155 Mbps modulation while the parameters such as the active region thickness should be properly optimized to obtain reasonable eye opening at 1.25 Gbps.