• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.749-761
• /
• 2010

The switching frequency of a power device is a very important parameter in the design of a parallel active power filter (PAPF), but so far, very little discussion has been conducted on it in a quantitative manner in previous publications. In this paper, an extensive analysis on the effects of the switching frequency on the performance of a PAPF is made, and a specification of the switching frequency values with different compensation results is presented. A first-order inertia element and a second-order oscillation element are considered as approximate models of a PAPF, respectively. The compensation characteristic for each order of harmonic current is obtained at different switching frequencies. Then, the THDs of each model for the system loads of a rectifier with resistance and inductance loads are proposed. The compensation results of a PAPF controlled as a first-order inertia element are better than those of a PAPF controlled as a second-order oscillation element. With two types of system loads which are rectifier with resistance and inductance loads and rectifier with resistance, inductance and capacitance loads, the THDs of the source current after compensation are presented with different switching frequencies. The compensation characteristics for the most widely used digital control system are investigated. The situation with an analog control is the theoretical characteristic and it is the best situation. The compensation characteristic of the digital control is worse than the compensation characteristic of the theoretical characteristic. Based on these analyses, the specifications of compensation characteristics with different switching frequencies are quite straightforward. Finally, a practical design example is studied to verify the application.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.215-216
• /
• 2006

In this paper, the antenna the with linear active phased array of $1{\times}16$ operated in DBS band was designed. The antenna was composed of sixteen radiating elements, sixteen active channels and five Wilkinson power combiners with 4-channel inputs, a digital control board and a stabilizing DC bias board. The radiating element of the array has the structure of a microstrip stack patch with a left-hand circular polarization. And, each active channel consists of a low noise ampilifier, a 3-bit digital phase shifter and a variable analog attenuator. The breadboard of linear active phased array antenna was also fabricated to test the electrical performances. The radiation patterns of the antenna were measured after correcting initial phases of each active channel in aechoic chamber. And also, the beam scanning chracteristcs of $10^{\circ}$, $20^{\circ}$, $30^{\circ}$ were measured.

• 경영과학
• /
• 제9권1호
• /
• pp.87-92
• /
• 1992

The purpose of this paper is to study the sensitivity analysis in the matrix game. The third type sensitivity analysis is defined as finding the characteristic region of an element of the payoff matrix in which the set of current active strategies is preserved. First by using the relationship between matrix game and linear programming, we induce the conditions which must be satisfied for preserving the set of current active strategies. Second we show the characteristic regions of active and inactive strategy. It is found that the characteristic regions we suggests in this paper are same with that of the type one sensitivity analysis suggested by Sung[3] except only one case.

• 한국소음진동공학회논문집
• /
• 제11권7호
• /
• pp.261-266
• /
• 2001

The flexural vibration of laminated composite beams with active and passive constrained layer damping has been investigated to design a structure with maximum possible damping capacity. The equations of motion are derived fro flexural vibrations of symmetrical,. multi-layer laminated beams. The damping ratio and model damping of the first bending mode are calculated by means of iterative complex eigensolution method. The direct negative velocity feedback control is used for the active constrained layer damping. It is shown that the flexible laminated beam is more effective in the vibration control for both active and passive constrained layer damping. and this paper addresses a design strategy of laminated composite under flexural vibrations with constrained layer damping.

• 한국컴퓨터정보학회논문지
• /
• 제8권1호
• /
• pp.1-6
• /
• 2003

능동규칙의 조건부 평가는 사건이 발생할 때마다 수행되기 때문에 조건부 처리 방법에 따라 시스템의 성능에 중요한 영향을 미친다. 그래서 능동 데이터베이스의 성능 향상을 위해 능동규칙의 조건부에 관한 연구가 매우 중요한 요소가 되며. 조건부에서 발생되는 연산 처리시간을 최소화 시켜야만 시스템의 성능을 높일 수 있다. 본 논문에서는 조인연산과 선택연산을 효율적으로 처리할 수 있는 트리 처리 시스템을 제안한다. 실험 결과 본 논문에서 제안한 트리 처리 시스템은 기존의 조건부 평가 방법보다 능동규칙의 조건부 처리에 대한 평가비용이 적게 소요됨을 알 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.641-645
• /
• 2001

In this paper, it is discussed that active noise control in a circular duct using smart foam. Firstly, it is demonstrated that the potential of the conventional smart foam, proposed by Fuller, for active noise control in a duct. Conventional smart foam is not applicable to active noise control in a duct having flow. Thus, this paper presents a ring-type smart foam as an alternative. The ring-type smart foam consists of polyurethane acoustic foam of lining shape and PVDF film embedded in the foam. The embedded PVDF element acts as an actuator to reduce noise at lower frequencies and the foam absorbs noise at higher frequencies. A filtered-x LMS controller is used to minimize the signal from the error microphone. Experiments are executed to reduce broadband and tonal noise.

• 산업기술연구
• /
• 제11권
• /
• pp.43-53
• /
• 1991

Two kinds of simple active oscillators are proposed and analyzed assuming that operational amplifier has two-poles frequency characteristics. The first circuit is composed of one operational amplifier, one resistor and one grounded capacitor. The second oscillator is realized with one operational amplifier and three resitors. Proposed oscillators have the low sensitivity of the oscillation frequency for little variations of the passive element values. By the experimental results obtained with Op-Amp. ${\mu}A741$, the simple oscillators can be useful for the frequency range $1.25 KHz{\leq}f_{01}{\leq}40KHz$ for the active-RC type or $45.45 KHz{\leq}f_{02}{\leq}400KHz$ for the active-R oscillator, and it is shown to transform the active-R oscillator circuit into the voltage controlled type. Therefore, two kinds of oscillator circuit are attractive for the IC realization, because they have one operational amplifier, one resistor and one grounded capacitor, or three resistors.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.43-48
• /
• 2009

In this study, through case studies, solar energy systems were coordinated with architectural plan elements and the others in apartment complex, and the energy performance was evaluated quantitatively through computer simulation PVSYST and RETScreen. As a results, in plan process of the application of solar energy systems in apartment complex, solar energy system should be considered as not only energy reducing technical element but also part of architectural plan element. And it must be considered with architectural plan elements, composition methods, energy storage methods, technical elements from the early basic plan stage. Photovoltaic system was installed on the wall facing the south and rooftop. The energy ratio of electric load was shown to be 5.5%. The result showed 7.2% when adding it to shading device additionally, and 6.4% in case of putting extra translucent module on windows. Active solar collecting system was applied on roof with the angle of 45. Maximum number of solar collector was 10 in a row, and the total solar collecting area was $915.00m^2$. The energy ratio of domestic water heating load by active solar hot water system is shown to be 11.4%.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.192-195
• /
• 2005

In this study, dynamic characteristics of an end-capped hull structure with surface bonded piezoelectric actuators are studied. Finite element modeling is used to obtain practical governing equation of motion and boundary conditions of smart hull structure. Modal analysis is conducted to investigate the dynamic characteristics of the hull structure. Piezoelectric actuators are attached where the maximum control performance can be obtained. Active controller based on Linear Quadratic Gaussian (LQG) theory is designed to suppress vibration of smart hull structure. It is observed that closed loop damping can be improved with suitable weighting factors in the developed LQG controller.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.333-334
• /
• 1989

Electrically active part of the piezoelectric sound element is a ceramic thin circular disk cemented to a metal base plate (using a type of thermosetting epoxy). The active part is a thin lead zirconate titanate disk (PZT). The piezoelectric sound element is so dimensioned that its basic resonance frequency is approximately if the center of the audible frequency band: This frequency is mainly determined by the geometry and the sort of the metal base plate materials. In this study, four kinds of PZT ceramic and two classes of thin metal base plate were prepared. It is observed that dielectric and pizoelectric properties relate to acoustical properties (particularly sound pressure level).