• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.313-316
• /
• 2005

In this paper, an active antenna for terrestrial DMB(Digital Multimedia Broadcasting) repeater is designed. This active antenna is consist of receiving antenna and LNA(Low Noise Amplifier), A receiving antenna fed by using a microstrip line and radiation part is designed with rectangular spiral structure. An receiving antenna with frequency range of 162$\sim$212MHz, gain of -10dBi and LNA with gain of 20dBi, noise figure of 2.2 at frequency range for T-DMB are achieved.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.7
• /
• pp.625-634
• /
• 2016

A full digital receiving active phased array antenna generates final receiving beams by digital beam forming of received digital signals in element-level that makes difficult to use typical near-field measurement method. Thus in this paper, a modified near-field measurement method which is suitable for full digital receiving active phased array antenna is proposed. Also the measured results of receiving beam pattern and G/T using developed L-band full digital receiving active phased array antenna are shown for the verification of proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.5
• /
• pp.325-335
• /
• 2018

We herein present a study on the active phased array antenna for receiving satellite broadcasting that can electrically align its polarization to that of target transmitters in its moving condition or in the Skew angle arrangement of the broadcasting satellite receiver. Hence, we have developed an active phased array structure composed of the self-developed Vivaldi antenna and multifunction core (MFC) chip, receiving RF front end module, and control units. In particular, the new Vivaldi antenna designed in the Ku-band of 10.7 - 14.5 GHz to receive one desired polarization mode such as the horizontal or vertical by means of an MFC chip and other control units that can control the amplitude and phase of each antenna element. The test results verified that cross-polarization property is 20 dB or higher and the primary beam can be scanned clearly at approximately ${\pm}60^{\circ}$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.2
• /
• pp.175-180
• /
• 2015

In this paper, GPS / GLONASS receiving a small active antenna is proposed. A microstrip patch antenna which supports dual-band (GPS and GLONASS) was optimized. The antenna size is $13{\times}13{\times}3.6mm$. The jig was changed to confirm the proposed antenna characteristic size, was adjusted to feed gap of the patch antenna, it was confirmed by change in LNA shield case or not. The antenna jig size is $65.6{\times}13{\times}0.8mm$. The maximum gain of the GPS band is 3.78dBi, the maximum gain of the GLONASS bands is 4dBi. To amplify the Satellite reception signal level, one-stage low noise amplifier(LNA) was designed. The LNA chip was using the BGA715 N7, the LNA gain is 19.9dB. The utilization possibility of the GPS / GLONASS receiving a small active antenna could be confirmed according to compare and analyze the simulation and measurement data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.1
• /
• pp.23-32
• /
• 2008

In the VHF range, active antennas are widely used for wideband applications due to their small size. Active antenna consists of antenna elements and amplifiers, which are directly connected to each other. Gain and noise-figure characteristics are very important for good sensitivity performance, because it is located at the front end of a receiving system. In this study, we developed an active dipole antenna with 5:1 bandwidth(100${\sim}$500 MHz), which consists of a dipole antenna and a P-HEMT amplifier. To obtain required performances, the antenna and the amplifier should be designed simultaneously. In order for that, we introduced an equivalent port concept to model the 1-port dipole antenna as an equivalent 2-port system. Using the proposed equivalent port, the performance of the active dipole antenna was simulated by the ADS. In order to measure the gain and noise-figure characteristics of the antenna, we utilized the same concept of the two-port equivalent impedance model. The measurement results for typical gain, NF and VSWR in the required frequency band were 8dBi, 9dB and 1.7:1, respectively. The radiation patterns at the principal planes were same as the typical radiation pattern of a dipole antenna. By comparing the simulation results with measured ones, it is confirmed that the proposed methods works well.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.44-52
• /
• 2007

In this paper, An active antenna of T-DMB was developed to equip to handhold gadgets by using LNA and a parasitic element allowing to miniature. The size of the fabricated active antenna is $80{\times}6{\times}0.4\;mm$ and FR4 is used for the substrate. The size of the proposed antenna is reduced by 38.8% at the operating frequency compared to one without a parasitic element, and a short stub. The proposed antenna shows improved performance at the measurement especially in the ratio of S/N compared with conventional monopole of 300 mm. The proposed antenna is well able to adapt into handhold gadgets for receiving T-DMB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.4
• /
• pp.59-65
• /
• 2022

In this paper, a digital active phased array antenna is briefly introduced and beam forming method for a dual-channel side-lobe blanking applied to blank the side-lobe of the main beam is described. Next, the antenna performance was verified from results of design and antenna near-field measurement for the antenna main beam and side-lobe blanking beam. Then, a single-channel side-lobe blanking beam forming method was proposed to reduce the number of channels than the existing system operating dual-channel side-lobe blanking beam and weight distribution for each element of the side-lobe blanking antenna was designed with the proposed method. Finally, the designed single-channel side-lobe blanking beam pattern and blanking ability were verified and compared with the dual-channel side-lobe blanking beam. In addition, by comparing/verifying the conventional dual-channel and the proposed single-channel side-lobe blanking beam patterns measured through the receiving near-field test of the digital active phased array antenna and their ability to blank side-lobe of the main beam, validity of the proposed method for forming single-channel side-lobe blanking beam was confirmed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1193-1203
• /
• 2008

An active antenna(AA) can have wider bandwidth and more gain with small antenna size than those of passive antennas. However, AA inherently generates thermal noise and spurious signals from an active device. Moreover, the spurious performance of AA is very important in a highly sensitive receiving system since it is located at the front end of the receiving system. In this study, we developed an AA with $100{\sim}500\;MHz$, having the output P1dB higher than 3 dBm and little spurious signals in real environments. To achieve such performance, we designed an AA with 3-stage amplifier using CD(common drain) FET and 2 BJTs. Its electrical performances were simulated using ADS. The measurement results for typical gain, NF, OIP3, VSWR and P1dB in the required frequency band were 9.7 dBi, 10 dB, 14 dBm, 1.7:1 and 3 dBm respectively. They are in good agreement with simulation results. The unwanted spectrum level of the proposed AA is $10{\sim}30\;dB$ lower than that of the antenna with CS(common source) FET configuration at a west suburban area of Seoul, which shows that the proposed AA can be applicable to a highly sensitive receiving system for detecting unknown weak signals mixed with broadcasting and civilian communication signals.

• Proceedings of the KSR Conference
• /
• 2005.05a
• /
• pp.903-908
• /
• 2005

Existing ATC/ATO/TWC system has a ATC(Automatic Train Control) antenna for receiving the speed code, a ATO(Automatic Train Operation) antenna for obtaining the exact distance to go to platform and TWC(Train and Wayside Communication) antenna for communication between on-board and wayside system. This paper proposes the ATO/TWC antenna with tele-powering module, telegram transmitter/receiver module. This antenna communicates with a passive type tag(wayside Precision Stop Marker) for the information of distance from the stop position and a active type tag for the door command and status in the platform.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.330-338
• /
• 2024

In this paper, a Ka-band high-output active phased array antenna device applicable to small radars and seekers was designed, and the improved performance was studied. The radiation device assembly consists of 1x8 arrangements, and the step flared notch antenna type. It shows low active reflection loss characteristics in broadband, and low loss characteristics by applying the air-strip feeding structure, and is designed to enable beam steering up to 45 degrees. The TRM(transmit receive module) output power is more than 2.0W per channel using GaN HPA in the transmitting path, and satisfies more than 25.0 dB gain and less than 6.0 dB noise figure in the receiving path. Accordingly, the Effective Isotropically Radiated Power(EIRP) of the antenna unit shows the performance of 0.00 dB or more and the receive gain-to-noise temperature ratio(G/T) of 0.00 dB/k or more. For demonstration, we have designed aforementioned planar array antenna which consists of 64 radiating elements having a size within 130 mm x 130 mm x 300 mm and weight of less than 4.9 kg..