• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.6
• /
• pp.473-476
• /
• 2018

Herein, a $2{\times}2$ subarray antenna is designed to implement a VHF band active electronically scanned array. The Yagi-Uda antenna is used as a radiating element. The bandwidth enhancement and miniaturization of the Yagi-Uda antenna are achieved by optimizing the diameter of a driven element and the length of a director. In addition, the grid reflector is utilized to improve the front-to-back ratio(FBR) and to reduce both the wind resistance and overall system weight. The fabricated $2{\times}2$ subarray antenna fully covers the VHF target band($0.98{\sim}1.02f_c$). The measured maximum gain is 10.61 dBi and the FBR is larger than 26 dB.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 1998.10a
• /
• pp.788-791
• /
• 1998

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.6
• /
• pp.438-444
• /
• 2019

In this paper, we proposed a 16-element array antenna design to improve signal detection performances. The array antenna characteristics, such as mutual coupling, pattern deviation, and half power beamwidth of the active element, were examined to obtain an optimal spacing between individual elements. The single element of the array antenna consists of an indirect feed using L-shaped feed and shorted radiating patch to achieve a broadband operation. Root mean square(RMS) errors based on the incident angle of the signal were calculated to verify the signal detection performance of the proposed antenna. The results demonstrate that the proposed array antenna with optimal spacing is suitable for detecting interference signals with low RMS error.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.94-102
• /
• 2013

We propose the mirror active element pattern (AEP) method for the radiation pattern computation of linear array antennas versus scan angles. The computation time for the radiation pattern of linear array antennas using the mirror AEP method is reduced by almost half compared to that using the AEP method because the number of AEPs of elements obtained by the full-wave simulation necessary for the radiation pattern computation of linear array antennas is reduced by almost half. The difference between the radiation patterns of linear array antennas obtained by the full-wave simulation and mirror AEP method is very small for wide scan angle range when the radiation pattern of an antenna element is symmetric.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.371-379
• /
• 2011

Active phased array antenna structure is used for modern multi-function radars. To search targets in high clutter environment, the radar receiver needs high dynamic range performance. Though active phased array antenna structure lead to increase of SNR, the SFDR is not increased. In this paper, high SFDR receiver of X-band active phased array radar was designed and manufactured. One channel digital receiver is connected to 32 T/R modules and one PCB assembly is composed to 2 channel digital receivers with RF part, ADC part, LO distribution part and digital down conversion part. A commercial FIFO board was used for digital receiver measurement about major performance in digital output signal condition. The measured digital receiver gain and SFDR is 33 dB and more than 81 dBc each.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.11
• /
• pp.857-867
• /
• 2018

Active array radar is evolving into digital active array radar. Digital active array radar has many advantages for making several simultaneous radar beams from the digital receive data of each element. A digital-type transceiver(TR) module is suitable for this goal in radar. In this work, the design results of an L-band digital TR module are presented to verify the possibility of fabrication for a digital active array antenna. This L-band digital TR module consists of a gallium-nitride-type HPA to achieve a more than 350-W peak output power and one-chip transceivers that include a digital waveform generator and analog digital converter. The receiving gain was 47 dB, the noise figure was less than 2 dB, and the final output type of the four channel receiving paths was one optic signal.

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.636-643
• /
• 2023

In this paper, a high-speed calibration method for phased array antennas in the far-field is presented A max calibration, which is a simplification of the rotating-element electric-field vector (REV) method that calibrates each antenna element only through received power, and a method of grouping calibrations by sub-array unit rather than each antenna element were proposed. Using the Proximal Policy Optimization (PPO) algorithm, we found a partitioning optimized for the distribution of phased array antennas and calibrated it on a subarray basis. An adaptive max calibration method that allows faster calibration than the conventional method was proposed and verified through simulation. Not only is the gain of the phased array antenna higher while calibration is being made to the target, but the beam pattern is closer to the ideal beam pattern than the conventional method.

• Journal of IKEEE
• /
• v.17 no.2
• /
• pp.135-139
• /
• 2013

This paper presents the 8-channel active module operated in Ka-band. The module is designed for the mobile satellite communication antenna systems, and the module structure has the merit to minimize the size and weight of the antenna systems by 30% compared with the conventional systems using the active module composed of single channel. This module was designed to be optimally operated by prohibiting the electrical interference among the individual channels. From the test results of the fabricated 8-channel active module, it can be confirmed that the maximum channel gain error is ${\pm}1.3dB$, the minimum channel output power is 21.5dBm, and the maximum gain variation by phase control is ${\pm}1.0dB$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1061-1070
• /
• 2009

In this paper, we have designed TDL(True-time Delay Line) for eliminating beam-squint occurring in active phased array antenna with large electrical size operated in wide bandwidth, and have tested its electrical performance. The proposed TDL device is composed of 4-bit microstrip delay line structure and MMIC amplifier for compensation of the delay-line loss. The measured results of gain and phase versus delay state satisfy the electrical requirements, also P1dB output power and noise figure meet the requirement. To verify the performance of fabricated TDL, we have simulated the beam patterns of wide-band active phased array antenna using the measured results and have certified the beam pattern compensation performance. As a result of simulated beam pattern compensation with respect to the 675.8 mm size antenna which is operated in X-band, 800 MHz bandwidth, we have reduced the beam squint error of ${\pm}1^{\circ}$ with ${\pm}0.1^{\circ}$. So this TDL module is able to be applied to active phase array antenna system.

• ETRI Journal
• /
• v.24 no.3
• /
• pp.197-204
• /
• 2002

This paper presents the results of the numerical simulation of a multibeam active phased array antenna for a High Altitude Platform Station (HAPS). The simulation takes into account the random errors caused by the non-identity of the array elements and the inaccuracy of the antenna calibration. The results of our statistical simulation show that the strict requirements on the sidelobe envelope for HAPSs can be met when the amplitude and phase distribution errors are minor, a condition which may be achieved by using digital beamforming.