• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.760-767
• /
• 2000

Recently, the protection of construction is demanded with environmental pollution. These protect modes are use of concrete admixture, coat of protective polymer and impregnate of surface with chemicals etc. The most widely used impregnation is economical and effective. The define of Impregnation for construction protect is reacted in and consolidated substrate after absorbed. The impregnation agents are Polyesters, Acrylic monomers, Epoxy and Silicone derivatives. Commonly, because the Silane has good water repellency and environmental advantages that it widely used to water proofing agents, dampproofing agents and absorption reducer for concrete of bridges. When application of Silane, it occurs pollution and harmfulness as included organic solvent. The manufactures have tired to emulsification of Silane for the reducing of the defects. The Silane emulsion is vary unstable and does not stored long periods, and it is diminished in good properties with internal reaction. In this study we tried to emulsification of Silane for effectiveness improvement and reduce pollution and hazard and discussed properties variation of emulsion. The Silane emulsions are achieved emulsifying with W/O and O/W type surfactants. It used 0.24% PVA as protective colloid and stable phase is creamy. The creamy Silane emulsion performance as the penetration depth and water absorption rate are above 4 mm and below 0.1. It stable about 6 month at room temperature.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.2
• /
• pp.131-136
• /
• 2002

As model waterborne acrylic coatings, mono-dispersed poly(butyl acrylate-methyl methacrylate) copolymer latexes of random copolymer and core/shell type graft copolymer were prepared by seeded multi-staged emulsion polymerization with particle size of $180{\sim}200$ nm using semi-batch type process. Sodium lauryl sulfate and potassium persulfate were used as an emulsifier and an initiator, respectively. The effect of particle texture including core/shell phase ratio, glass transition temperature and crosslinking density, and film forming temperature on the film formation and final properties of film was investigated using SEM, AFM, and UV in this study. The film formation behavior of model latex was traced simultaneously by the weight loss measurement and by the change of tensile properties and UV transmittance during the entire course of film formation. It was found that the increased glass transition temperature and higher crosslinking degree of latex resulted in the delay of the onset of coalescence of particles by interdiffusion during film forming process. This can be explained qualitatively in terms of diffusion rate of polymer chains. However, the change of weight loss during film formation was insensitive to discern each film forming stages-I, II and III.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.758-762
• /
• 1998

In preparing void latex particles by emulsion polymerization, the weight mean particle size of which is ranged $0.3{\mu}m{\sim}1.5{\mu}m$, reaction parameters were investigated in order to elucidate their effects on the size distribution and the solid content of emulsion polymer. Experimental results showed that the weight mean particle size of hydrophillic core polymer was reduced as the concentration of sodium dodecylbenzene sulfonate (SDS) increased. The size of void polymethyl-methacrylate-polystyrene composite latex particles became larger as the concentration of styrene monomer and the sodium persulfate increased. However, the size of void latex particles was reduced as the feeding rate of acrylic acid increased. The solid content of emulsion polymer was strongly dependent on the addition of stylene monomer. By increasing the concentration of styrene monomer the solid content of emulsion polymer increased linearly.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.225-230
• /
• 2001

Cast-in-place foamed concrete is a high porous material placed as base the layer of mortar screeds in the panel heating system, so the quality of mortar is affected by it. Therefore, this study is aims to investigate how the absorption characteristics of foamed concrete influences on mortar screeds according to the foamed ratio-62%, 67% and 72%- and the surface treatments of foamed concrete-water and acrylic emulsion primer spray, etc. The result of this study shows that water-spray in the surface of foamed concrete has a good effects to reduce mortar cracking.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.10a
• /
• pp.89-92
• /
• 1995

For the development of lilght weight cement concrete with high durability, this study used perlite and paper sludge ash by the light weight material, and polypropylene fiber by the reinforcment, and poly-acrylic ester emulsion by the matrix improvement. According to the increasing mixture ratio of fiber and use of polymer, the light weight polypropylene fiber reinforced polymer cement ratio of fiber and use of polymer, the light weight polypropylene fiber reinforced polymer cement concrete were showed high resistance for frost damage.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.459-470
• /
• 2018

Cellulose nitrates were used for folklore artifacts(ornamental beads and pipes in hatstrings, frames of eyeglasses, ornamental eyeglass cases, headband ornaments, and jeogori buttons) between the 19th and 20th centuries; however, they are susceptible to cracking, crazing, embrittlement, and crumbling due to deterioration. To consolidate and adhere deteriorated cellulose nitrate folklore artifacts, water-soluble acrylic emulsion adhesives were investigated. For consolidation, Plextol D 498, which has the lowest viscosity in low concentrations, was used. In adhesive films whose glass transition temperature(Tg) is lower than room temperature, the tensile stress and modulus decreased and the strain increased; therefore, the flexibility was high. The Plextol D 498 and Plextol D 498 and Dispersion K 52 films maintained their adhesiveness and flexibility after artificial-sunlight-accelerated ageing, and Plextol D 498 and Dispersion K 52 films hardly caused yellowing. Plextol D 498 was the most stable for accelerating ageing. A low concentration of Plextol D 498 emulsion resulted in the best permeability on the surface of cellulose nitrate, compared with other acrylic emulsions. To prevent ornamental hatstrings from cracking, crazing, embrittlement, and crumbling, a Plextol D 498 emulsion was used. After applying low concentrations(1%, 3%) of the emulsion to consolidate the fragments and high concentration to adhere the fragments, the ornamental hatstrings were protected from crumbling by deterioration, and their fragments were well-adhered. To preserve it from deterioration by oxygen and humidity, the treated ornament was sealed with an oxygen-barrier film using a low-humidity oxygen scavenger.

• Applied Chemistry for Engineering
• /
• v.28 no.4
• /
• pp.454-459
• /
• 2017

In this study, aqueous acrylic emulsion adhesives were prepared using various surfactants and their properties were also investigated. Solids content, conversion, particle size distribution and initial adhesion properties of the prepared adhesives were compared with each other. The solid content of the adhesives was evaluated 60% and the conversion rate of the emulsion polymerization was 97% at 2 wt% concentration of synthesized surfactants. The particle size distribution analysis revealed that the size distribution of adhesive particles was 290~470 nm when the synthesized cationic surfactant was added. The initial adhesion and adhesion time were also improved. The maximum adhesive strength was found to be 2.55 kgf when using a single surfactant (POE 23), and superior to that of using other surfactants. It was confirmed that the corrosion inhibition of the adhesive prepared by adding the cationic gemini surfactant was maintained for 48 hours.

• Polymer(Korea)
• /
• v.34 no.2
• /
• pp.89-96
• /
• 2010

Adhesive binders with core-shell structure of organic/organic pair were prepared by emulsion polymerization of acrylic monomers, such as methyl methacrylate(MMA), ethyl acrylate(EA), n-butyl acrylate(BA), and styrene(St). Ammonium persulfate (APS) was used as an water soluble initiator in the presence of an anionic surfactant, sodium dodecyl benzene sulfonate (SDBS). Non-woven fabric and leather were impregnated with the adhesive binder. The surface of the impregnated fabric and leather were treated with plasma technique and then kinetics analysis and mechanical properties were measured. The conversions of the polymerization of core-shell binder (MMA/EA, MMA/BA) were greater than 90%. When the core-shell binder was prepared at equimolar conditions, the increasing effect of the core-shell binder on the state peel strength of the impregnated and plasma-treated non-woven/non-woven fabric has the order of MMA/St, EA/BA, BA/MMA, EA/St, and EA/MMA. When the core-shell binder was prepared at non-equimolar conditions, the increasing effect of the core-shell binder on the state peel strength of the non-woven fabric/leather has the order of MMA/BA, BA/EA, MMA/EA, St/MMA, and EA/St.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.434-441
• /
• 2010

Sodium polyacrylate (PAANa) was synthesized by inverse emulsion polymerization method to absorb excess water in concrete. Liquid paraffin was used as a continuous phase. Acrylic acid (AA) was neutralized by aqueous sodium hydroxide solution (8 M). Different amount of N,N'-methylene bisacrylamide (MBA) was used as a crosslinking agent to change crosslinking density of the synthesized PAANa. The size distribution of synthesized particles was measured by particle size analyzer. Swelling ratio of crosslinked PAANa was evaluated from the equation in D. I. water, cement aqueous solution, and $Ca(OH)_2$ aqueous solution. The FTIR spectroscopy was used to characterize $Ca^{2+}$ ion interaction with PAANa. Incorporation of 1.0 wt% PAANa into cement increased compressive and flexural strength approximately 30% and 10%, respectively, compared with those of ordinary portland cement.

• Journal of Conservation Science
• /
• v.33 no.5
• /
• pp.345-354
• /
• 2017

A mural was discovered in the Ssanggyesa temple located in Jindo island, during repair of the Daeungjeon Hall. A study was conducted to determine the binding medium used for preparing the mural. Pyrolysis/GC/MS and IR spectrometry were used to analyze a painting specimen. Direct approach and on-line methylation approach were attempted for the pyrolysis/GC/MS. In IR analysis, the spectra of the specimen were found to be different from those of Asian lacquer, yellow lacquer, animal glue, and acrylic emulsion resin. They were also not identical to the standard IR spectra of drying oils such as linseed oil. Pyrolysis/GC/MS results of the specimen were different from those of Asian lacquer, yellow lacquer, animal glue, and acrylic emulsion resin. In the mean time, palmitic acid, octadecanoic acid, nonanedioic acid, and octadecenoic acid, which are characteristic pyrolysis products of dried drying oil, were detected. In addition, the pyrolysis/GC/MS chromatograms of the specimen and dried drying oil were also very similar. Therefore, it was concluded that the painting was prepared using drying oil as a binding medium.